What is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
View 1 RepliesI just recently (and very expensively) purchased a HWIC-1ADSL for my 1841 router.
Unfortunately, it doesn't display in the configuration - nor any lights appear on it for power/link.
My first guess is I need to upgrade my IOS. The current version on my 1841 is 12.4(17). Which appears to be pretty current.
Here is my current config build for a Cisco 2620 using a Wic-1ADSL to connect to a Qwest ADSL ISP:
interface FastEthernet0/0
ip address 172.16.0.1 255.255.0.0
ip nat inside
no ip mroute-cache
[code]...
For some reason, it won't connect at all. I've changed the callin requirement on the ppp authentication between "callin" to "callout" - even removed the line completely for a no-authentication scenario.The only responses that come back on a repetative nature when doing a debug are:
Vi2 PPP: Authorization NOT required
and
Vi2 PPP: No remote authorization for call-out
I’m testing a 1841 with 2 WIC-1ADSL cards, but the connections are dropping every 30-50mins. If I swap the cars out for HWIC-1ADSL’s then the lines are stable. I’ve had the profiles on the lines dropped the 4mb down and 512k up but I’m still getting the same issue.
I’ve tried a few 1841’s with various IOS’s and different WIC’s but still get the same result.
We have open a division in the UK and are using DSL as a back up to a T1-E1, so I was going to use a standard DSL Modem but thought the WiC-1ADSL-I-DG would be better. However I can seem to get the card up and running. Here is the interface config and sh int atm.
interface ATM0/1/0
ip address dhcp
ip access-group 102 in
ip inspect SDM_LOW out
[code]....
That's part of the sh int amt.
Is there any difference in performance between HEIC-2T & HWIC-4T
View 2 Replies View RelatedI have a Cisco ASA5505 with Frontier ADSL. I broke into their crappy little modem and obtained the settings needed to replace their modem with a 2621 router with a WIC-1ADSL module. I have a static IP from Frontier which is on my ASA5505 and the Dialer interface on the 2621 gets its address from Frontier via DHCP. There are devices behind the ASA which I need access while in the field, IP Cameras, Seed Treater, etc., so I have Anyconnect running on the ASA and can access everything from my laptop, iPhone and iPad from whereever. The issue arises when my laptop is in house and communicating with my parent company and I try to make a cell phone call off the network extender. The call is choppy since there is no QoS and the data is strangling the voice. Since I have control over the 2621, I added another network and NAT it into Frontier without them knowing. I have since placed the network extender on this network as well as a WAP200 that is wide open for my customers when they are in the office. Doesn't fix the problem but...
I have now added Evertek Wireless internet with a static IP also but they use a reservation based on the MAC Address of my interface of the ASA. This plugs directly intot the ASA via ethernet (I would assume their antenna is just a wireless bridge). I set route tracking on the Evertek side and use the Frontier as a backup and all devices on my NAT network still funcion on Frontier DSL and all my nornal data traffic is out Evertek. The issue is that the Evertek Wireless is not very fast or reliable (today in during a snow storm, it could barely keep an internet connection). And I had a problem with Anyconnect using either connection. I got that working. But think that the "ip address x.x.x.x y.y.y.y dhcp setroute" on the Evertek side messed things up from a routing standpoint when I would connect from the outside on the Frontier side. For testing, I switched the tracking around and now the connection on the Frontier side does not work but that is besides the point.
Frontier is going to try out an ADSL/2 connection next week which brings up another issue; all Frontier connections come into my buidling on a single 4-pair wire so if they go down, all my internet except the Evertek goes down. I have a Raven Slingshot coming for installation shortly that cannot go down; it will provide RTK (sub-inch accuracy GPS) to my customers that have auto-steer and auto-shutoff capabilities in their tractors via cellular data modem. So, while they are planting their crops in the field, if my connection goes down, their tractor will not function.
I also had a Cisco UC320W but it died a few days after it went off warranty so I replaced it with a Dell Server running 3CX IP PBX that supports Cisco SPA525G2 and SPA501G IP Phones. There is a 3CX iPhone app that allows me to receive calls while in the field, it uses a proprietary tunnel that I have open on the ASA. With 4-pair coming into my building, I will be left with a single 1-pair for phones so I am considering a SIP provider instead.
Can/should I move the Evertek ethernet to the third ethernet interface on the 2621 and track the Frontier DSL against the Evertek (backup) on the 2621 side and use the ASA to track the ADSL/2 against the 2621? Should I acquire an 1841 (or some other device that suppports the HWIC) with a ADSL/2 card and use HSRP between the 2621 and 1841? Is that even possible?
I have an existing C2821 router (2 onboard GE + 1 HWIC-2FE) currently. Like to add another 1 HWIC-2FE. Saw this doc on Cisco website which states Max of 2 HWIC-2FE for Cisco2821. Want to confirm this is indeed so as another link states max of 1 HWIC-2FE.
View 3 Replies View RelatedI am looking for a way to use a 3G connexion on ASR1000.Is it possible to install HWIC module of ISR2 in SPA slot or use an USB modem on the RP?
View 2 Replies View RelatedI want a low cost solution router with 16 10/100 routed ports...The idea is to club 16 different segments on ofc to this router via media convertor and there will be dynamic protocols such as EIGRP or higher running between these segments.
The router needs to be security enabled...the equipments needs to be a router by defination (not a layer 3 switch)..As per my understanding there is limitation on number of HWIC-2 FE that can be put in ISR G2 series due to which I cannot reach that figure...
Kindly let me know if i can use SM-ES3-16-P in the place of HWIC-2FE for this kind of requirement.
Does the ASR-1000 accept an HWIC module, or must one go to a SIP/SPA for all modules?
View 1 Replies View Relatedif the card HWIC-1SER is the equivalent card HWIC-1T for 1861 router?
View 3 Replies View RelatedI have cisco 3845 router with 4 HWIC-2FE card none of them is detected the message displayed is [code]
View 7 Replies View Relatedmeaning slap an HWIC-4ESW into a router, say, an 1841, create an ether channel out of them to connect to my switch?
View 6 Replies View RelatedIs there an ethernet WIC/HWIC that supports NAT for the 2811. I have one 4 port 10/100 card but it doesn't support NAT overload.
View 5 Replies View RelatedI just added an HWIC-16A to a Cisco 2911 router for use as a Terminal Server.[URL]I've installed and configured the card properly. However, I receive the following error message:Attempt from Cisco CLI
View 2 Replies View RelatedI have a Cisco 2811 router with c2800nm-adventerprisek9_sna-mz.124-2.T6.bin as IOS and i wsh to install this HWIC 4port to increase available ports on my router. Wish to know if this is going to work,that is, if i installed it the IOS available will recognise this card
View 4 Replies View RelatedI have cisco router 3925 and i add install HWIC-4ESW, as i sew on cisco documents you can hot swap the hwic without reload the router but i it's not working at all. How to do it ?
View 1 Replies View RelatedI'm trying to backup my primary WAN with secondary backup connection - 3G WAN through Cellular 0/0/0.Point is that I need to track some external IP address on my primary interface, for examle 8.8.8.8. If it is not reacheable, then router brings up backup connection - 3G. This can be done by using dialer-watcher.Simple.But unfortunately my primary WAN interface is an FastEthernet, which is the coonected to a switch, switch to WAN . There is no dialer-watch commands on it. Thats sad .
One more time :
WAN -> SWITCH -> ROUTER(WITH 3G HWIC and Fa 0/0 connected to switch).
I have a scenario where multiple branches are connected to Head Office via DSL links. The branches are located in differenct exchanges, everyone once in a while ALL branches go down at the exact same time except 3 branches and those 3 branches don't have ATM interface on the router, rather they have external DSL modem, all other branches that face the disconnection (for couple of minutes) have either HWIC-1ADSL-M or HWIC-2SHDSL and the DSL line is directly plugged into the card. [code]
I tried so many solutions like adding "operating-mode auto" command under the subinterface, IOS upgrade, changed dynamic routing protocol from EIGRP to OSPF... Nothing worked, on the logs of the router it just shows "EIGRP neighbor down", at the time of the problem I can't ping any of the affected branches on their WAN ATM interface although it stays physically "up up".Could the problem be a missing command that I need to add under the subinterface? Something maybe related to clocking or timeout or..?Note that hte problem occurs randomly, every few days, sometimes every 10 days, and all branches with ATM interface go down at the exact same time.
I' ve come across an weird ospf issue between my router connected via layer 2 service provider link, details as below.We have a base station router for satelite termination at service provider end connected via Layer 2 vlan link to a head end C3945, current interface for head end is a layer 2 vlan and layer 3 ip address lives under sub interface, config as below
-Head End router
-Cisco 33945
i have some issue with Hwic-4ESW, if i install one card(Hwich-4ESW) is working all port then i install one more card ( Hwic-4ESW) it not working.interface and vlan is up but from my PC to port Hwic-4esw not working. what is problem on this ?
View 9 Replies View RelatedIn our Environmet we have 3845 Edge Router Current Ios Version is Version 12.4(1a),(c3845-advipservicesk9-mz.124-1a.bin)As management got another fiber leased line(Single Mode) for which i have install SFP slot part number HWIC-1GE-SFP,after installation of HWIC-1GE-SFP in router the follwing slot is showing
GigabitEthernet0/1/0
%HWIC_1GE_SFP-6-SFP_IN: Interface GigabitEthernet0/1/0 1000BaseLX SFP has been inserted
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/1/0 xx.xx.xx.xx. YES manual up down
for testing purpose i tried the same procedure into the switch and its working fine where as in Router the link is not coming up ,
According to specifications fo Cisco ISR G2 2911, it has got 4 EHWIC slots. But in [URL] appears that Cisco2911 supports only 2 HWIC-2FE or only 2 EHWIC-1GE-SFP-CU.
View 1 Replies View RelatedI am trying to configure multiple dsl-groups on a HWIC-4SDHSL-E module and the option does not exist. According to the Cisco documentation I should be able to do this, but I only get pairs as an option.
1921(config-controller)#dsl-group ? pairs Link number <cr>
[URL]
This is what I am trying to do which I have done before on the 1841.
dsl-group 0 pairs 0, 1
shdsl annex A-B
shdsl rate 4096
[Code].....
is there any known issue in configuring multilink ppp using an old WIC-1T and a newer HWIC-1T on the same Cisco 1841 router ?
View 2 Replies View RelatedI have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Replies View RelatedI was looking an HWIC card for CISCO2901-SEC/K9. We have one internet connection (ADSL) current.Now we want to backup internet connection from cable service provider. I will implement IPSec on this HWIC.
What HWIC cards can I choose for this router?
I have got 3845/3945, I would like to increase HWIC slot density for HWIC 4 PORT ISDN BRI S/T ports through the NM/NME/NMX slots, Is there any measns to do that?
View 2 Replies View RelatedI have Cisco 2801 router with IP Base image, i have upgraded its image into advance Ip services for using IP SLA features but after upgradation HWIC card not showing in configuration.
When i recall IP base image then configuration show presence of HWIC card but with advance IP services HWIC card not showing.
We have configured new 2911 router with HWIC-2T with it.However we are seeing serial interfaces up, but can hardly ping other end. Again we are seeing a lot of CRC errors on serial interface.
But if we connected same cable, with other old router 2811, it works fine. Confiuration is same on both the routers. [code]
I have two HWIC-4T1/E1 in two 2821's I can not for the life of me find software so I can configure them in the routers. I see them in the inventory but don't see them in show ver. I'm assuming that the software is not recognizing them. I've tried a bunch of releases that software advisor says they are supported and am wondering if I'm just doing something wrong.
NAME: "4 port clear channel T1/E1 HWIC on Slot 0 SubSlot 0", DESCR: "4 port clear channel T1/E1 HWIC"PID: HWIC-4T1/E1 , VID: V02 , SN: xxxxxxxxxx
NAME: "Two port T1 voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "Two port T1 voice interface daughtercard"PID: VWIC-2MFT-T1= , VID: 1.0, SN: xxxxxxxxxx
Cisco 2821 (revision 53.51) with 245760K/16384K bytes of memory.Processor board ID xxxxxxxx2 Gigabit Ethernet interfaces2 Channelized/Clear T1/PRI ports1 Virtual Private Network (VPN) ModuleDRAM configuration is 64 bits wide with parity enabled.239K bytes of non-volatile configuration memory.62720K bytes of ATA CompactFlash (Read/Write)
I would like to ask if a cisco 2811 running on an ios c2800nm-adventerprisek9-mz.124-25a.bin should be able to make an HWIC-1FE card work? I am also not detecting the card on any show commands. Plus i am seeing that all the LEDs (FDX/COL,100 and LINK/ACT) are lit steadily even though there is no cable attached to it, is it safe to say that the card could be defective?
View 6 Replies View Related