I have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Repliesi have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedThe setup is a S2S VPN with failover to 3G HWIC in a Cisco 1941 however the IPSEC tunnel needs to remain up through 3G if ADSL fails.The failover works ok, however when plugging ADSL back in, the - "sh crypto session" shows both dialer 0, and dialer 1 with the crypto map session to the other side of the VPN and either side is now not pingable.The NoIP DDNS updater client runs on a server in the network and all IP resolution to host1,host2 works ok (other side of VPN is Cisco 1921 with ADSL HWIC and 3G HWIC). [code]
View 5 Replies View RelatedI just added an HWIC-16A to a Cisco 2911 router for use as a Terminal Server.[URL]I've installed and configured the card properly. However, I receive the following error message:Attempt from Cisco CLI
View 2 Replies View RelatedI am trying to configure multiple dsl-groups on a HWIC-4SDHSL-E module and the option does not exist. According to the Cisco documentation I should be able to do this, but I only get pairs as an option.
1921(config-controller)#dsl-group ? pairs Link number <cr>
[URL]
This is what I am trying to do which I have done before on the 1841.
dsl-group 0 pairs 0, 1
shdsl annex A-B
shdsl rate 4096
[Code].....
I had purchased a HWIC-8A in an effort to provide terminal server capabilities into multiple routers. I had found a document that I thought would take me through the configuration but it doesn't appear that the command syntax is the same on the 2911's as it is in the document. Does any know how I would need to get this configured on the 2911 router?
Here is the document I was referencing
[URL]
I'm trying to backup my primary WAN with secondary backup connection - 3G WAN through Cellular 0/0/0.Point is that I need to track some external IP address on my primary interface, for examle 8.8.8.8. If it is not reacheable, then router brings up backup connection - 3G. This can be done by using dialer-watcher.Simple.But unfortunately my primary WAN interface is an FastEthernet, which is the coonected to a switch, switch to WAN . There is no dialer-watch commands on it. Thats sad .
One more time :
WAN -> SWITCH -> ROUTER(WITH 3G HWIC and Fa 0/0 connected to switch).
is there any known issue in configuring multilink ppp using an old WIC-1T and a newer HWIC-1T on the same Cisco 1841 router ?
View 2 Replies View RelatedI'm trying to learn a little about Cisco router setup, since I'm fairly well versed in configuration. I have an 1841 w/ K9 that I'd like to set up as a WAN Router to hot swap if one of ours goes down. I installed a VWIC2-1MFT-T1/E1 MultiFlex card in Slot 1 of the router.
Currently, if I run a "show diag", the VWIC2-1MFT-T1/E1 shows up in Slot 1 but in the configuration I can't see it or configure it. Am I missing an enable or something? I thought I had to declare card type but I can only do that on the existing card, the router doesn't seem to recognize that the card is there in any place other than "show diag".
I've been given an 1841 with a 3G HWIC card installed to test with. I need to set up some sort of VPN to our ASA, the problem is though these 3G cards get a random public IP, so what options do I have to create a VPN tunnel from this router to the ASA without the 1841 getting a static public IP?
View 3 Replies View RelatedI am trying tu update the firnmware of a HWIC 3G-GSM within an 1841. What is the correct firmware?
I have tried
K2_0_7_35 and K1_0_2_18 from [URL]
[Code]......
I just recently (and very expensively) purchased a HWIC-1ADSL for my 1841 router.
Unfortunately, it doesn't display in the configuration - nor any lights appear on it for power/link.
My first guess is I need to upgrade my IOS. The current version on my 1841 is 12.4(17). Which appears to be pretty current.
I am trying to configure a shdsl port on a 2911 router for CO mode of operation.The dsl-group auto command does not seem to change the port to operate in CO mode and the link will not come up to a remote router that has a card installed operating in CPE mode.The configuration I have applied for the shdsl controller is.
controller SHDSL 0/1/0
dsl-group auto
!
!
Do I need to use a HWIC-4SHDSL card for the CO mode operation?
I have not yet completed my CCNA, however I have managed to configure a 1841 router with 1 x HWIC-ADSL1 and it also has 1 x HWIC-AG-AP-A which is the only part I am unable to get working.
The Wi-Fi (Dot11Radio) config has enabled me to see the SSID from wireless devices, but they never get an IP address. I need them to get the same IP range as the DHCP service I have in there 203.35.10.xxx, there is no option for "IP ADDRESS DHCP" only "IP ADDRESS POOL LAN" Lan is of course my DHCP pool name. however I cannot have the same DHCP pool on both Dot11Radio interfaces.
I know I'm missing one very simple command, but as I've never worked with Radio on Cisco equipment, I am unsure how to fix it.
Then once I get that worked out, I need changing the access from OPEN to WPA or WPA2, etc..
IOS Software on Router is C1841-ADVSECURITYK9-M - Version 12.4(9) T
I can upgrade to a better version of software if needed, I only have a 32mb Flash and 128Mb Ram.
The current Radio Config is:
!
interface Dot11Radio0/1/0
no ip address
no ip redirects
[Code]....
my office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies View RelatedI am configuring a 1841 router for use in small out office. I will use the s0/0/0 for main WAN T1 connection. I then wanted to use the ATM0/1/0 WIC-1-ADSL card as a failover. I am using weighted static routes for failover. Fe0/0 is LAN interface. When I go into SDM and look at the ATM interface it says this configuration is unsupported?
1. Can't I just get a DSL modem and connect it to fe0/1 and not use ATM WIC and use below for failover?
2. If I have to use ATM WIC what needs to be configured for it to work with Att aDSL?
I have a Cisco 1841 router with an HWIC-ADSL module installed. My ADSL connection is PPPoA with a dialer interface and I have been provided 6 ip's from my provider to use on this service. Previously I have connected Fa0/0 on the 1841 straight onto my network and used NAT and ACL's on the 1841, I would now like to change this and have Fa0/0 connected to a Palo Alto firewall and use the Palo Alto to provide NAT, Firewall & site to site VPN functions. What config would I require on the 1841 to allow me to use one of my ISP IP addresses on the Palo Alto to allow it to be a VPN endpoint? Do I need to configure the 1841 in bridge mode?
View 3 Replies View RelatedI have a cisco 1841 router in place. I also have a ADSL module which fits into the cisco router. My understanding is that if configured correctly, If the primary circuit were to fail (Ethernet Circuit MPLS), the ADSL would take over services until such time the ethernet link becomes available.
Therefore the ADSL circuit is used as a resilient link. If this is possible, can the Cisco 1841 be setup to automatically switch over to the ADSL? Would there be some sort of heart beat between the ethernet circuit and adsl circuit?Also from the other end of the Cisco router, the connection goes into a firewall. If the Cisco handles the failover, I assume I would not need to configure anything on the firewall.
The end users beyond the firewall, should be able to continue, however the performace would be degraded?
I am trying to configure a Cisco 1841 to allow the users to access the internet. This is my first step with ppp. All the rest of the configuration is ok but I don't know how to setup the interfaces Dialer0 and ATM0/0/0.
Need very basic configuration that I can analyze and use on my device?
We have an ADSL2+ line from a WIC in a 1841, everything has been fine for the last few years and then the last few months the connection going down. When checking the interfaces the ATM0/0/0 is up up and the same for the dialer interface we are using, they are both up/up, but this still needs a reload of the router to be functional again, shutting the interfaces does not bring the connection back up.
I am not an expert on ADSL lines, I have never really had a problem with anything previously. The router was running Netflow to a network monitor wondering if this or logging was causing an issue with entries in the buffer??
Here is an output of show dsl int, would change the firmware, it has been fine all this time before though we are running IOS 12.4(24)T1 advseck9-m, as far as I can seen from our ISP the config for ADSL is all correct. [Code]
We have 2 router cisco 2621XM and want to configure a VPN between them, but first we want to configure ADSL in both with the card installed.
View 2 Replies View RelatedI need to configure configuring pppoe ADSL on cisco 887VG
View 5 Replies View RelatedBasically I have a simple LAN of 30 users and 2 servers that sit on a private address range (192.168.1.1 - 254). I have a Cisco 1921 router with 2 Gigabit Ethnet interfaces and have installed a 2 port Ethernet module to expand interfaces,I have Two Internet providers that provide me an Optic connection to a converter and then a CAT 5 cable. On both of these connections have private public assigned IP addresses.I have a email server and webserver on the LAN (192.168.2 and 192.168.1.3) and with to port forward various ports to these servers - 25, 80, 443 3389, and 2222.
In my external DNS I have two MX records for the mail server (mail.globalhomegroup.com) that point to 2 A records - one record for the publicly assigned IP address of one ISP and another IP address for the other ISP. Ideally what i would like is for mail to be delivered to the first ISP Ip address - the one with the lower MX weighting and then if that line goes down, through the IP address of the second MX record - the backup ISP we are using.
So I guess I am port forwarding to the inetrnal server IP addresses via one of the two external interfaces.At the same time I need to allow internal users to access HTTP, HTTPS etc.So I have managed somehow to configure the external interfaces of the routers to connect to the ISPs and have managed to assign IP info to intenral LAN interface. I can telnet to the router from the Internet via Dialer0 or Dialer1. Other than that I am totally stuck - I have tried to configure and debug NAT etc but cant see wood for the trees now. Basically the port forwarding is not working and i am not sure if the config I have done is in anyway correct.
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies View RelatedI've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
We have a cisco 1941 with line t1 Symmetric, (Also have Cisco 1841 unused, but works) I would like to connect the Cisco 1841 to four Adsl Backup lines in case the T1 or the Main cisco 1941 go down I know a BGP is needed on our ISP site,
How can i connect four Adsl lines to The cisco 1841 (Backup) and make them work in a Load Balancing way.
I only know a little about programming a CISCO router but I know the config I setup is not working...
Here is what I want to do...
The ISP provides us with IP Addresses via DHCP. Our public address is NOT static so the interface on the DSL Module needs to be provisioned to get a DHCP address with a CLASS C License.The IP address of the Router should be 10.0.0.10 subnet=255.255.255.0The LAN Clients need receive their IP address via DHCP EXCEPT for a range of 100 addresses. The lan Clients only need about 40 DHCP addresses.ONE of the Lan Clients (10.0.0.3) needs to have ports 25, 1723, and others forwarded to it.
Below is the config I am trying to use but I can't even ping the router from the LAN.
We upgrade our Internet service in our India office which required a new router. The local vendor suggested an 1841, so that is what we have. It has two fastethernet ports on it.
The ISP (Airtel) provided the following IP address information:
Public WAN IP : 122.181.23.200/30
WAN IP : 122.181.23.202SUBNET MASK : 255.255.255.252GATEWAY : 122.181.23.201Pri DNS : 125.22.47.125Sec DNS : 202.56.250.5
[Code]......
What is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
View 1 Replies View RelatedI have an existing C2821 router (2 onboard GE + 1 HWIC-2FE) currently. Like to add another 1 HWIC-2FE. Saw this doc on Cisco website which states Max of 2 HWIC-2FE for Cisco2821. Want to confirm this is indeed so as another link states max of 1 HWIC-2FE.
View 3 Replies View RelatedI am looking for a way to use a 3G connexion on ASR1000.Is it possible to install HWIC module of ISR2 in SPA slot or use an USB modem on the RP?
View 2 Replies View RelatedI want a low cost solution router with 16 10/100 routed ports...The idea is to club 16 different segments on ofc to this router via media convertor and there will be dynamic protocols such as EIGRP or higher running between these segments.
The router needs to be security enabled...the equipments needs to be a router by defination (not a layer 3 switch)..As per my understanding there is limitation on number of HWIC-2 FE that can be put in ISR G2 series due to which I cannot reach that figure...
Kindly let me know if i can use SM-ES3-16-P in the place of HWIC-2FE for this kind of requirement.
Does the ASR-1000 accept an HWIC module, or must one go to a SIP/SPA for all modules?
View 1 Replies View Related