I just recently (and very expensively) purchased a HWIC-1ADSL for my 1841 router.
Unfortunately, it doesn't display in the configuration - nor any lights appear on it for power/link.
My first guess is I need to upgrade my IOS. The current version on my 1841 is 12.4(17). Which appears to be pretty current.
What is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
View 1 Replies View RelatedI have not yet completed my CCNA, however I have managed to configure a 1841 router with 1 x HWIC-ADSL1 and it also has 1 x HWIC-AG-AP-A which is the only part I am unable to get working.
The Wi-Fi (Dot11Radio) config has enabled me to see the SSID from wireless devices, but they never get an IP address. I need them to get the same IP range as the DHCP service I have in there 203.35.10.xxx, there is no option for "IP ADDRESS DHCP" only "IP ADDRESS POOL LAN" Lan is of course my DHCP pool name. however I cannot have the same DHCP pool on both Dot11Radio interfaces.
I know I'm missing one very simple command, but as I've never worked with Radio on Cisco equipment, I am unsure how to fix it.
Then once I get that worked out, I need changing the access from OPEN to WPA or WPA2, etc..
IOS Software on Router is C1841-ADVSECURITYK9-M - Version 12.4(9) T
I can upgrade to a better version of software if needed, I only have a 32mb Flash and 128Mb Ram.
The current Radio Config is:
!
interface Dot11Radio0/1/0
no ip address
no ip redirects
[Code]....
[URL]The Cisco 2811 does not support the HWIC-4T1/E1 module. But, I installed HWIC-4T1/E1 on the 2811 running 124-24.T2.
View 3 Replies View RelatedI’m testing a 1841 with 2 WIC-1ADSL cards, but the connections are dropping every 30-50mins. If I swap the cars out for HWIC-1ADSL’s then the lines are stable. I’ve had the profiles on the lines dropped the 4mb down and 512k up but I’m still getting the same issue.
I’ve tried a few 1841’s with various IOS’s and different WIC’s but still get the same result.
I need to know the Cisco 1841 Router FE Maximum Bandwidth Support and the Cisco 3825 Router GE Maximum Bandwidth Support. I cannot find this information in Cisco for these old devices.I would like to have the platform capability for all situation (only IP base, with QoS, with ACL, with encryption, etc.)
View 1 Replies View RelatedI'm trying to backup my primary WAN with secondary backup connection - 3G WAN through Cellular 0/0/0.Point is that I need to track some external IP address on my primary interface, for examle 8.8.8.8. If it is not reacheable, then router brings up backup connection - 3G. This can be done by using dialer-watcher.Simple.But unfortunately my primary WAN interface is an FastEthernet, which is the coonected to a switch, switch to WAN . There is no dialer-watch commands on it. Thats sad .
One more time :
WAN -> SWITCH -> ROUTER(WITH 3G HWIC and Fa 0/0 connected to switch).
is there any known issue in configuring multilink ppp using an old WIC-1T and a newer HWIC-1T on the same Cisco 1841 router ?
View 2 Replies View RelatedI have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Replies View RelatedI'm trying to learn a little about Cisco router setup, since I'm fairly well versed in configuration. I have an 1841 w/ K9 that I'd like to set up as a WAN Router to hot swap if one of ours goes down. I installed a VWIC2-1MFT-T1/E1 MultiFlex card in Slot 1 of the router.
Currently, if I run a "show diag", the VWIC2-1MFT-T1/E1 shows up in Slot 1 but in the configuration I can't see it or configure it. Am I missing an enable or something? I thought I had to declare card type but I can only do that on the existing card, the router doesn't seem to recognize that the card is there in any place other than "show diag".
I've been given an 1841 with a 3G HWIC card installed to test with. I need to set up some sort of VPN to our ASA, the problem is though these 3G cards get a random public IP, so what options do I have to create a VPN tunnel from this router to the ASA without the 1841 getting a static public IP?
View 3 Replies View RelatedI am trying tu update the firnmware of a HWIC 3G-GSM within an 1841. What is the correct firmware?
I have tried
K2_0_7_35 and K1_0_2_18 from [URL]
[Code]......
my office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies View RelatedI'm looking for a HWIC card that will support SC fiber connections for a 2811. I know of the HWIC-1GE-SFP but this one only support the LC connections.
View 2 Replies View RelatedI have a 2811 ISR, a lab unit with almost nothing yet configured other than some IP networks on serial and FE interfaces to ping to other lab routers. And I have one HWIC-4ESW installed, and I amrunning IOS 15.2.I want to set the card as a single routable interface and just have the ports act like switch ports, which I imagine is the default design of these cardsI work a lot with Cisco 891 ISRs so figured it's the same here, assign an IP to interface Vlan1 and all is well. That was wrong, obviously more config is required.It seems there are a lot of differing answers out there, so far none what worked for me. The best looking one I could find said to assign an IP to the Vlan 1 interface, then go to each of the four FE interfaces on the switch module.
View 3 Replies View RelatedJust double-confirm that 2811 is compatible with HWIC-2FE based on your experience? Which IOS is compatible with HWIC-2FE? [URL]
View 3 Replies View RelatedJust need to verify if HWIC-2T is compatible with the Cisco2800 routers?
View 4 Replies View RelatedMaybe this was listed in the release notes for the product and I missed it, but can this item support Etherchannel in a 2801 router? I installed the module into the router and the router recognizes the module. I can configure the ports as access or trunk ports, but I am unable to configure the channel-protocol or the channel-group for the Etherchannel. The IOS on the router is 15.1 M with the upgraded Bootloader version 12.3.
View 1 Replies View RelatedI Have installed HWIC-2T card in my cisco 1921 router but it is not able to detected in router. find the ver of router
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Tue 20-Mar-12
[Code]......
I have cisco2811 and HWIC-1CE1T1-PRI in the main office are using to connect 10 branches ( 10 ISDN lines) for Data.
I have available channels in the used E1 so I can use them for voice using PVDM2-64 ?
We have been facing a problem at my company ! We have a Cisco Router 1921 with one HWIC-4ESW in trunking with a RuggedCom switch RSG2100.When I use the GigabitEthernet port to make a trunk, I create 2 sub-interfaces (one for each Vlan) and configure the Port on Switch as Trunk, the inter-VLan routing works with no problem.But now I need to use this configuration using the HWIC-4ESW on Router, and I can't do this work. I try creat interface Vlan for each vlan, and try creating the VLans at Router Vlans database, but no way. At router I enter in interface and try to do the switchport trunk command to add a Vlan, but doesn't work.
View 4 Replies View RelatedDoes Cisco 1921-SEC/K9 support HWIC-4ESW ? I require 4 x 10/100 Ethernet ports
If yes how many ? are there any drawbacks if i use this module instead of a switch?
We have two cards HWIC-4ESW on router 3845 but we need that the two cards 8 ports conected betwen, if a pc on port 1 can ping a pc conected on port 8 on second card. tis comunication can,t doing a pc on port 1 can,t conected a pc on port 8.
the configuration is the folowing
interface FastEthernet0/0/0
switchport access vlan 100
speed 100
[Code].....
I am working on a backup system for my WAN. Verizon quoted the HWIC-3G-CDMA-V to work with my Cisco 1721 router. I have a bunch on these routers on a shelf and thought I would use them for the 3G network. Looking at the Cisco web site it does not list the 1721 as being able to work with this HWIC. I thought it might not be listed as the 1700 series are End of life. Whether it will work?
View 3 Replies View RelatedI have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies View Relatedwould Cisco 1841 model router with IOS version 12.4(15)T10 support vpnclient-winx64-msi-5.0.07.0440-k9.exe client software?
View 1 Replies View RelatedI'm just getting started with cisco kit so you will have to bare with me.I have a cisco 1841.i have a very wierd issue of routing...i cannot ping and browse through this.
View 3 Replies View RelatedI have a problem accessing my wireless router through VLAN sub-interface on my Cisco 1841 router. My hardware:
Cisco Catalyst 2960 switch (192.168.100.4 /24)
Cisco Catalyst 3550 switch (192.168.100.6 /24)
Cisco 1841 router (192.168.100.7 /24)
Asus RT N66U wireless router (192.168.100.2 /24)
Here's my network topology:
I have two VLANs - 10 and 20. 2 DHCP pools are configured on 2 1841's interfaces - 192.168.1.0 /25 and 192.168.1.128/26 with default router sitting on 192.168.1.1 and 192.168.1.129 respectively. No issues with obtaining IP address from any of those pools.Laptop connects to L3 3550 switch (switchport access vlan 10), which, in turn, connects to 1841 router through trunk (with VLANs 10 and 20 allowed).3550 is connected to 2960 through trunk with VLANs 10 and 20 allowed.Wireless router is connected to 2960.I can successfully ping my wireless router and outside world from 1841 from fa0/1 interface, but not from fa0/1.10 or fa0/1.20 sub-interfaces - all packets got dropped. My laptop can obtain IP from both pools (depending on port I connect it to), but can't ping my wireless router and anything beyond it.
I attach my configs:Cisco Catalyst 3550:interface FastEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk switchport port-security mac-address sticky speed 100!interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk!interface FastEthernet0/3 switchport access vlan 10 switchport mode access!interface FastEthernet0/4 switchport access vlan 20 switchport mode access!Cisco 1841:
ip dhcp pool Vlan10DHCP network 192.168.1.0 255.255.255.128 default-router 192.168.1.1 dns-server 208.67.220.220 domain-name home.local
!ip dhcp pool Vlan20DHCP network 192.168.1.128 255.255.255.192 default-router 192.168.1.129 dns-server 208.67.220.220 lease 0 12
interface FastEthernet0/1 ip address 192.168.100.7 255.255.255.0 duplex auto speed auto!interface FastEthernet0/1.10 description VLAN10 Sub Interface encapsulation dot1Q 10 ip address 192.168.1.1 255.255.255.128!interface FastEthernet0/1.20 description VLAN20 Sub Interface encapsulation dot1Q 20 ip address 192.168.1.129 255.255.255.192!
Routing table on 1841:
[code]....
why pppoe support has been dropped from 12.4 for the 1841's? (1801's 12.4 still supports pppoe)
View 6 Replies View RelatedWhat cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?
View 1 Replies View RelatedI have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?
View 1 Replies View RelatedI have a Cisco 1841 router at home with version 12.4(13r)T advanced ip services. The setup is extremely simple:
1) PPPOE dialer to my service provider over ADSL
2) Nat overload on the dialer interface.
3) 2 V LAN s one for home network (wired) and one for wireless both v LAN's are connected through interface v LAN s respectively.
My problem is when I configure static NAT to map RDP or any other protocol to inside hosts this does n`t work.
"
ip nat source static tcp 192.168.20.3 2222 interface Dialer1 2222
ip nat source static tcp 192.168.20.3 3389 xx.xx.xx.xx 3389 extendable
ip nat inside source list 20 interface Dialer1 overload
"
When I open wire shark and sniff the traffic on home computer which is the one I`m trying to reach I can't see any traffic. And While performing Nat debugging I am also not able to see traffic going to that port (for example 3389).