Adding HWIC To Slot 1 Of Cisco 1841?
Jan 2, 2012
I'm trying to learn a little about Cisco router setup, since I'm fairly well versed in configuration. I have an 1841 w/ K9 that I'd like to set up as a WAN Router to hot swap if one of ours goes down. I installed a VWIC2-1MFT-T1/E1 MultiFlex card in Slot 1 of the router.
Currently, if I run a "show diag", the VWIC2-1MFT-T1/E1 shows up in Slot 1 but in the configuration I can't see it or configure it. Am I missing an enable or something? I thought I had to declare card type but I can only do that on the existing card, the router doesn't seem to recognize that the card is there in any place other than "show diag".
View 7 Replies
ADVERTISEMENT
Jun 12, 2011
I have a Cisco 2811 router with c2800nm-adventerprisek9_sna-mz.124-2.T6.bin as IOS and i wsh to install this HWIC 4port to increase available ports on my router. Wish to know if this is going to work,that is, if i installed it the IOS available will recognise this card
View 4 Replies
View Related
May 19, 2011
I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?
View 1 Replies
View Related
Jul 3, 2011
I'm trying to backup my primary WAN with secondary backup connection - 3G WAN through Cellular 0/0/0.Point is that I need to track some external IP address on my primary interface, for examle 8.8.8.8. If it is not reacheable, then router brings up backup connection - 3G. This can be done by using dialer-watcher.Simple.But unfortunately my primary WAN interface is an FastEthernet, which is the coonected to a switch, switch to WAN . There is no dialer-watch commands on it. Thats sad .
One more time :
WAN -> SWITCH -> ROUTER(WITH 3G HWIC and Fa 0/0 connected to switch).
View 4 Replies
View Related
Feb 19, 2012
is there any known issue in configuring multilink ppp using an old WIC-1T and a newer HWIC-1T on the same Cisco 1841 router ?
View 2 Replies
View Related
May 10, 2011
I have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Replies
View Related
Aug 19, 2012
I've been given an 1841 with a 3G HWIC card installed to test with. I need to set up some sort of VPN to our ASA, the problem is though these 3G cards get a random public IP, so what options do I have to create a VPN tunnel from this router to the ASA without the 1841 getting a static public IP?
View 3 Replies
View Related
Sep 30, 2010
I am trying tu update the firnmware of a HWIC 3G-GSM within an 1841. What is the correct firmware?
I have tried
K2_0_7_35 and K1_0_2_18 from [URL]
[Code]......
View 6 Replies
View Related
May 14, 2008
I just recently (and very expensively) purchased a HWIC-1ADSL for my 1841 router.
Unfortunately, it doesn't display in the configuration - nor any lights appear on it for power/link.
My first guess is I need to upgrade my IOS. The current version on my 1841 is 12.4(17). Which appears to be pretty current.
View 9 Replies
View Related
Dec 5, 2012
I have not yet completed my CCNA, however I have managed to configure a 1841 router with 1 x HWIC-ADSL1 and it also has 1 x HWIC-AG-AP-A which is the only part I am unable to get working.
The Wi-Fi (Dot11Radio) config has enabled me to see the SSID from wireless devices, but they never get an IP address. I need them to get the same IP range as the DHCP service I have in there 203.35.10.xxx, there is no option for "IP ADDRESS DHCP" only "IP ADDRESS POOL LAN" Lan is of course my DHCP pool name. however I cannot have the same DHCP pool on both Dot11Radio interfaces.
I know I'm missing one very simple command, but as I've never worked with Radio on Cisco equipment, I am unsure how to fix it.
Then once I get that worked out, I need changing the access from OPEN to WPA or WPA2, etc..
IOS Software on Router is C1841-ADVSECURITYK9-M - Version 12.4(9) T
I can upgrade to a better version of software if needed, I only have a 32mb Flash and 128Mb Ram.
The current Radio Config is:
!
interface Dot11Radio0/1/0
no ip address
no ip redirects
[Code]....
View 1 Replies
View Related
Jun 5, 2011
my office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies
View Related
Aug 28, 2011
We currently have out T1 attached to a 5505. We have IPsec site to site tunnels that also terminate on the outside interface of the 5505.
We are getting rid of the T1 and bringing in a manged MPLS circuit which will run off of a 1841 ISR. I would like the 5505 to pretty much work as is with little change. Whats the easiest way to accomplish this? Of course the MPLS will come with new external IP.
Current Design ---> T1<------>[asa5505]<------->[LAN]
New design---------> Mpls<------->[1841]<------>[asa 5505]<------->[LAN]
Questions:
1. Whats the easiest way to drop in the 1841 without having to change all my ASA acl's.
2. How would I terminate my ipsec site to site tunnels on asa outside interface. Now that the WAN interface is on 1841 and not ASA how would I terminate the other side of tunnel? Can I leave my tunnel end points on ASA or do they now have to terminate on 1841?
3. How would I configue outside interface on ASA to communicate out 1841 MPLS?
View 2 Replies
View Related
May 9, 2012
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies
View Related
Jan 24, 2011
My onboard eithernet quit working so I got PCI slot 1 and it doesnt work either I have 3 slots and none work. The pc won't even acknowledge that they are pluged in, but the lights on the card are flashing. Had it working once but when I moved it to my desk and booted it up nothing worked again. The PC will boot and run fine but no web. Clean install of XP and all is the same!
View 1 Replies
View Related
Jan 17, 2012
internet on tv which has no Ethernet slot
View 3 Replies
View Related
Jul 17, 2012
how can i check the memory chips in the DIMM slots on a Cisco 2800 router ,my intention is I need to upgrade the IOS on the router for which I need to upgrade the DRAM and flash. Any CLI command available for the same ,as it is not very feasible to open the remote routers to check the DIMM configuration.
View 1 Replies
View Related
Jun 12, 2013
What is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
View 1 Replies
View Related
Mar 13, 2013
we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 Replies
View Related
Jan 9, 2012
Currently using a CSS1506 for our reverse proxy SSL.I have a couple of questions
1 - Does the 11506 use an internal disk as well as the one in slot 0 ?
2 - I have a spare mem card in slot1, how can I copy all of the required boot files etc to slot 1 in case of a card failure in slot 0?
View 2 Replies
View Related
Jun 12, 2011
My laptop does not have a standard telepone line connecting socket. Is it possible to use a converter plug to use the boardband socket instaed?
View 2 Replies
View Related
Feb 10, 2012
Just finished my first build and everything went pretty smoothly but my wireless network card wasn't working. I noticed after I opened it back up that in order for my to screw the card in place it made the right side of the card tilt up.
So I just set it in the PCI slot correctly but there's no way for me to screw the card in place. I know my MOBO is set properly. My graphics card fits perfectly.
View 3 Replies
View Related
Jun 21, 2010
i have a brand new dell studio 1558
on my old computer i used an external PCMCIA modem from my cellular company , the modem uses a sim card to connect to the internet..
can i place the sim card inside the computer and use it as i used the previous modem ?
[URL]
View 13 Replies
View Related
Dec 31, 2011
Every one i want to know ws-c4503E series 3 -slot chassis . I have compatibility issues with MEM-C4K-FLD64M AND S45EIPBK9-12240SG will work.
View 2 Replies
View Related
Dec 26, 2011
I have a large quantity of ASA5520's and ASA5540's that need to be quickly assessed and RTV'd (if need be) if they are found to be upgraded ASA5510's.
My concern is because of this recent release-note by Cisco: [URL]
Is there a way to check the amount of DIMM slots on a unit through console or do I have to physically check each and every one?
View 2 Replies
View Related
Jan 15, 2013
I've got this syslog alarm from nexus 7018. I am wondering what the slot 19 is here.
2013 Jan 15 23:59:22 r1 %PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 19 has changed, Top Ejector is OPEN, Bottom Ejector is CLOSE
2013 Jan 15 23:59:24 r2 %PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 19 has changed, Top Ejector is CLOSE, Bottom Ejector is CLOSE
View 5 Replies
View Related
Sep 23, 2012
Is it possible to connect directional antenna on slot 1 5Ghz radio on the 1522SB and use it for client access ? As per the deployment guide there is a note that Omni antenna is required on slot1. If i connect directional antenna on slot 1(how will the AP know if its omni or dierctional antenna which is connected anyway) , will it work ?
View 3 Replies
View Related
Nov 14, 2011
Cisco 1900 , 2900 and 3900 have Interface Slots and Service Module Slots , My question is which type of card is support this slot.
View 6 Replies
View Related
Nov 13, 2011
I remember there is one command which can tell you which memory slot has how much big memory in Cisco 2800 or 3800. But at this moment, I just couldn't recall this command. I checked "show diag" but didn't see any information about memory.
View 9 Replies
View Related
Dec 17, 2012
I bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
View 3 Replies
View Related
Mar 25, 2013
I have cisco 4510R L3 switch with installed 2 Sup on slot 5 and 6. the current active Sup is in Slot5 i want to make active Sup6 in slot 6 which is currently standby sup in chassis. Is there any way to make standby Sup to ACTIVE without reloading any of the Supervisor. however there is two way as per my understanding -
1. we can reload the active Sup so that standby Sup will take charge. - (redundancy reload shelf)
2. we can focefully switchover the state of Sup's by (redundancy forcefully swithover) but in above both cases reload will be performed by one of the supervisor. which i don't want.
View 2 Replies
View Related
Apr 27, 2013
There is a cisco ws-c6509,recently it appear error log “%FABRIC-SP-6-TIMEOUT_ERR: Fabric in slot 5 reported timeout error for channel 11 (Module 3, fabric connection 1)”. When I reload the device,the error log disappear.But a few days later,it appears again.I try to replace the slot 3 (WS-X6704-10GE),the error log continues.The IOS version is 's72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF8"
View 1 Replies
View Related
Mar 27, 2013
I have an existing C2821 router (2 onboard GE + 1 HWIC-2FE) currently. Like to add another 1 HWIC-2FE. Saw this doc on Cisco website which states Max of 2 HWIC-2FE for Cisco2821. Want to confirm this is indeed so as another link states max of 1 HWIC-2FE.
View 3 Replies
View Related
Jun 24, 2012
I am looking for a way to use a 3G connexion on ASR1000.Is it possible to install HWIC module of ISR2 in SPA slot or use an USB modem on the RP?
View 2 Replies
View Related
