Cisco Switching/Routing :: Command To Check Memory Slot In 3800 Routers?
Nov 13, 2011
I remember there is one command which can tell you which memory slot has how much big memory in Cisco 2800 or 3800. But at this moment, I just couldn't recall this command. I checked "show diag" but didn't see any information about memory.
View 9 Replies
ADVERTISEMENT
Aug 22, 2012
I got trouble when tried to save configuration by 'write memory' command.
cisco WS-C2960-48PST-L (PowerPC405) processor (revision G0) with 65536K bytes of memory. Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(52)SE,RELEASE SOFTWARE (fc3)
Cat2960#wr
Building configuration...
% Warning: Saving this config to nvram may corrupt any network management or security files stored at the end of nvram.
Continue? [no]: no % Configuration buffer full, can't add command:
After this message continue typing "yes" sometime that switch reload all times. The service compress-config command is not available anymore.
View 3 Replies
View Related
Apr 25, 2013
I am on a call right now troubleshooting some latency issue. The CPU usage on the sup card is low. Don't see any drops or input errors. I am aware that the switch and its modules have capability limits. Is there command I can run which will tell me if any module is overloaded or if the fabric/backplane is over utilized?My chassis is WS-C6513 and sup card is WS-SUP720-3B.
View 3 Replies
View Related
Jul 17, 2012
how can i check the memory chips in the DIMM slots on a Cisco 2800 router ,my intention is I need to upgrade the IOS on the router for which I need to upgrade the DRAM and flash. Any CLI command available for the same ,as it is not very feasible to open the remote routers to check the DIMM configuration.
View 1 Replies
View Related
Mar 13, 2013
we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 Replies
View Related
Dec 31, 2011
Every one i want to know ws-c4503E series 3 -slot chassis . I have compatibility issues with MEM-C4K-FLD64M AND S45EIPBK9-12240SG will work.
View 2 Replies
View Related
Jan 15, 2013
I've got this syslog alarm from nexus 7018. I am wondering what the slot 19 is here.
2013 Jan 15 23:59:22 r1 %PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 19 has changed, Top Ejector is OPEN, Bottom Ejector is CLOSE
2013 Jan 15 23:59:24 r2 %PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 19 has changed, Top Ejector is CLOSE, Bottom Ejector is CLOSE
View 5 Replies
View Related
Jan 17, 2013
I have a question about ACLs on Cisco 3800 router. I tried to configure extended IP access-list. However, I couldn't add more rules into some of the ACLs when the number of rules increase to about 120 rules. These extended IP access-lists are assigned to gigabit ethernet interface and sub-interface (VLAN interface).
Is this caused by some kind of maximum number of rules supported?
View 3 Replies
View Related
Mar 25, 2013
I have cisco 4510R L3 switch with installed 2 Sup on slot 5 and 6. the current active Sup is in Slot5 i want to make active Sup6 in slot 6 which is currently standby sup in chassis. Is there any way to make standby Sup to ACTIVE without reloading any of the Supervisor. however there is two way as per my understanding -
1. we can reload the active Sup so that standby Sup will take charge. - (redundancy reload shelf)
2. we can focefully switchover the state of Sup's by (redundancy forcefully swithover) but in above both cases reload will be performed by one of the supervisor. which i don't want.
View 2 Replies
View Related
Apr 27, 2013
There is a cisco ws-c6509,recently it appear error log “%FABRIC-SP-6-TIMEOUT_ERR: Fabric in slot 5 reported timeout error for channel 11 (Module 3, fabric connection 1)”. When I reload the device,the error log disappear.But a few days later,it appears again.I try to replace the slot 3 (WS-X6704-10GE),the error log continues.The IOS version is 's72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF8"
View 1 Replies
View Related
Oct 15, 2004
I'm trying to connect my new Dell Dimension 8400 (3.0Ghz/512Mb/XPsp1) to my home wireless network. I installed two diiferent PCI adapter cards in my one available PCI slot -- an older D-Link (11b) and a brand new Netgear (11g) (which Dell Sales assured me is compatible). Both cards detected my Netgear wireless router and provided an excellent internet connection, so I'm assuming they were seated properly. The problem is that every time I shut down the system I get the blue screen of death with the following message:
-Hardware Malfunction
-NMI: Parity Check/Memory Parity Error
-The System has halted
The system runs and shuts down perfectly when the PCI cards are removed. D-Link and Netgear Support technicians told me I have to contact Dell, but Dell Support doesn't seem to have an answer for me. Which wireless PCI adapter cards are truly compatible with Dell hardware?
View 9 Replies
View Related
Mar 17, 2011
I am using cisco ASA 5540, Is there any command to check the tunnel uptime?
View 2 Replies
View Related
Jun 27, 2011
I am using ASA5500 series box which has a site to site tunnel terminated on it.Is there any command by which we can check the up time of the tunnel.
ASA# sh isakmp sa
Active SA: 1 Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)Total IKE SA: 1
1 IKE Peer: x.x.x.x Type : L2L Role : responder Rekey : no State : MM_ACTIVE
View 2 Replies
View Related
May 14, 2012
how can i check that ASA is passing traffic? Also what command we can use to make sure VPN is working fine.
View 2 Replies
View Related
Jan 7, 2013
Need to check how many tunnels IPSEC are running over ASA 5520.Tried commands which we use on Routers no luck?
View 6 Replies
View Related
Oct 4, 2011
is there a cisco command to check the list of incoming vlans on a catalyst 4640 or at least that will give you the same output?we're having an issue with an ethernet circuit, links are up but ping won't go through(no ACLs) and I want to see if the vlan tag from the the other side(side B) is properly reaching side A.
View 1 Replies
View Related
Nov 2, 2011
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies
View Related
May 29, 2012
According to my boss every 3 to 4 months he has to restart our 2821 with a 16-esw module installed because of a low memory issue dealing with CEF. Here is the exact error message.
%% Low on memory; try again laterJun 8 11:18:51.777: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:19:51.823: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" %%
Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
Jun 8 11:20:51.868: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:21:51.914: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed
View 4 Replies
View Related
Nov 22, 2011
Today, one of our Cisco 3750 got unmanaged from NOC, we were able to ping the switch, also, traffic was flowing fine but not able to telnet or local login.On trying to login through console following messages were coming:
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
[code].....
We given power on reset, after which we were able to login switch again. I wanted to know the actual reason behind it and if there is any other way to recover switch other than power reset.?
View 17 Replies
View Related
Nov 29, 2012
on the asr 1004 , how test and check if the SFP receive power or signal from the MUX? any command to do that?
View 3 Replies
View Related
Jan 11, 2012
I wonder whethere it is possible to check the the IOS version on the standby sup720 of a 6500? if yes, what command would you use?
View 5 Replies
View Related
Dec 25, 2011
We have configured a Fex port as acces port but the port no up becouse appear in suspended state, i think the problem is a vlan mistmach as appear in the consistence-parameter information but i not found in what part allow the correct vlan, the N2K are connected to 2 N5K, and 5K are connected to2 N7K
%ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 41 on Interface Ethernet101/1/48 are being susp ended. (Reason: Vlan is not configured on remote vPC interface) [code]
View 4 Replies
View Related
Dec 17, 2012
I bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
View 3 Replies
View Related
Sep 5, 2012
ISRG2 (c2951-universalk9-mz.SPA.152-4.M1.bin) has 512 MB of DRAM. Periodically it runs out of memory: [code]
1. Why "show process mean" command shows less memory than 512 MB? Processor Pool (248 MB) + I/O Pool (58 MB) ~ 310 MB only?
2. *Init* process holds more memory than normal (202 MB). What may cause this?
View 2 Replies
View Related
Jul 25, 2012
have 3 Catalyst 3750 in same stack, the IOS version is 12.2(53)SE2. Today we can not telnet/ssh to this switch, but ping is ok, and switch function is ok. I try to access the console port, it show "low on memory, try again later". After I reboot the master switch in the stack, the master switch change to another switch, then I can telnet/ssh to this switch. I check the Ciscoworks server syslog report, there are many MAC address flapping error message, and I beleive the MAC address flapping occured before several weeks. ( the G2/0/15 & G3/0/15 is connect to a VMware ESX server and the EtherChannel config mismatch with this Catalyst 3750 switch ) How to mention the root cause of the "low on memory" problem and what is the abnormal memory usage ( free memory percentage below ?% )?
View 5 Replies
View Related
Nov 3, 2011
i have a Ws-C3550-24-Emi switch and i need to upgrade its flash memory to 32Mb. I couldn't find any documents in cisco website about the memory upgrade guideline. Possible to upgrade this switch to 32Mb? If so, what's the max of memory i can upgrade? and the part number for this type of memory?
View 4 Replies
View Related
Dec 28, 2011
I have a bootflash in 4507R with the size of 60MB. I upgraded the ios from cat4500-ipbasek9-mz.122-37.SG1.bin (12.8MB Size) to cat4500-entservices-mz.122-37.SG1.bin (13.8 MB SIZE) and deleted the previous IOS.But previous IOS is still getting shown in sh bootflash: command. Furthermore, dir bootflash: commands shows there is only one IOS , which is running. How I can free the space from bootflash , as I again have to upgrade the another new IOS ( of 16MB), which I tried through solarwinds tftp and couldn't upload successfully because of its limitation. Now, If I try to upload the new IOS through FTP, it gives me memory space error. How I can free the space captured by old IOS and also how I can delete the 3rd unknown entry of IOS (shown below output of commands)?
View 4 Replies
View Related
Jul 15, 2009
I have a 3560 connected to an edge device and I keep etting this error. I have turned off proxy arp and turned off ip cef under the interface, however I lot connectivity to the internet when I did that. I can't seem to find any documentation on this error. I understand what it means, I just don't know how to resolve the problem.
View 3 Replies
View Related
Dec 9, 2012
I am noticing high memory used on my 2960-S I am running 15.0(2)SE. I am concerned that there is a problem with this model and IOS.
View 2 Replies
View Related
Jun 7, 2013
I have a 3560 connected to an edge device and I keep etting this error. I have turned off proxy arp and turned off ip cef under the interface, however I lot connectivity to the internet when I did that. I can't seem to find any documentation on this error. [code]
View 5 Replies
View Related
Oct 26, 2011
1. How to check the history alarms in Router 7609?
2. How to check whether an Interface was down?
View 1 Replies
View Related
Oct 28, 2012
how I can check the qos counters and stats for interfaces on my cat 6509 ?
View 1 Replies
View Related
Jan 17, 2013
Cisco... Have two new 3750X switches (24P-L, and 48PF) trying to stack. Brought them up together a few weeks ago with the 24P using LANBase and the 48 IPBase. The expected happened. They saw each other in the stack ring, and the 24 port was excluded due to license miss match. This was corrected. Now both are IPBase.Now I have the two switches stacked, and boot the 48 and 24 at the same time. Monitoring the 48 I get a check message "FIPS: Flash key check: End, Not found. FIPS: Stacking Not Found". The 48 does confirm the stack cable is connected. This happens early in the boot process, before master election.OK.... Now looking at the 24 Port. After applying the new license, and actually booting successfully and few times. It will no longer load the boot file. Wants an environment variable. Going to have to dig into ancient history for that. Had to deal with that one about 8 years ago. Do not feel that is part of the stack disable issue though.
View 2 Replies
View Related