Cisco Switching/Routing :: 4510R L3 / Make Active Sup6 In Slot 6 Which Is Currently Standby Sup In Chassis
Mar 25, 2013
I have cisco 4510R L3 switch with installed 2 Sup on slot 5 and 6. the current active Sup is in Slot5 i want to make active Sup6 in slot 6 which is currently standby sup in chassis. Is there any way to make standby Sup to ACTIVE without reloading any of the Supervisor. however there is two way as per my understanding -
1. we can reload the active Sup so that standby Sup will take charge. - (redundancy reload shelf)
2. we can focefully switchover the state of Sup's by (redundancy forcefully swithover) but in above both cases reload will be performed by one of the supervisor. which i don't want.
View 2 Replies
ADVERTISEMENT
Jan 15, 2012
A customer wants to get the back-plane load of a cat4506-e chassis with a sup6-E supervisory card.A would like to check how many bus are used on the backplane and if the command "sh envi chassis" is the good and only command to be used ?I'm not sur that there is only one bus on the cat4506-E as with a sup7 card the backbone speed can change.
View 2 Replies
View Related
Dec 31, 2011
Every one i want to know ws-c4503E series 3 -slot chassis . I have compatibility issues with MEM-C4K-FLD64M AND S45EIPBK9-12240SG will work.
View 2 Replies
View Related
Feb 7, 2012
The 6509 Series Switches support the scenario VSS Active-Active Chassis, I would like to setup both switch's as one virtual switch but working at the same time, not with Active - Stand By Chassis.
My plans it to create PortChannel accross both Switches 6509 in order to have 2 links one connected to one slot/switch and the other connected to slot/switch in the second 6509 for servers redundancy.
View 1 Replies
View Related
Dec 9, 2012
I have multiple 6509 vss switch. and i notice when the standby chassis reboot I didn't get any snmp trap, but I got when the active one reboot. my question is is there any mib out there for detecting and got a trap when standby reboot?
View 2 Replies
View Related
Sep 25, 2012
Any have experience on triggered failover on VSS deployment with 1 VS-720-10G-3C in each chassis? I tried using "redundancy force-switchover" but after that the 20G VSL is flapping up & down and cannot be up normally, we got 1 FWSM in each chassis, any configuration need to fit in this kind deployment? BTW, if I shutdown the power source of VSS active chassis, both FWSM & VSS can failover normally.
View 3 Replies
View Related
Mar 4, 2013
I am running HSRP on three 4506 switches..S1(active) S2( standby) and S3(listen)..S1 is active for all the vlansRight now, I wanted to make S3 active for two vlans: vlan 10 and 19What would be the impact to the end hosts?Also, can you tell me why the arp is not syncing for all the three devices? [code]
View 4 Replies
View Related
Dec 16, 2011
I am working on two Nexus 7010 with 5.1.5 NX-OS version. I configure HSRP traditionnaly, Nexus 1 with a priority of 200 and Nexus 2 with a priority of 100 for all vlan.
When I change the priority of a vlan to 200 to 50 for example, Nexus 2 become active and Nexus 1 standby. The problem is that when I do a traceroute from a PC the packet take the Nexus 1 as defaut gateway all the time.....
For information I have a peer link between the 2 Nexus for vPC.
View 9 Replies
View Related
Sep 30, 2012
I have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.
View 1 Replies
View Related
Apr 22, 2012
I went through the configuration guide for 4500 series switches for NSF/SSO for failover between Sup's. I just wanted to know that that are we supposed to run the SSO command on both of the supervisors? Secondly, are we only supposed to run the nsf process under EIGRP on the secondary supervisor and routing peers and not on the primary supervisor?
View 2 Replies
View Related
Oct 19, 2012
We are expanding out LAN network with more 2960 access switches. All the access switches are suppose to be connected to core switch (4507R) but i have less port on the core switch.
On the core switch we have two supervisor engines (WS-X4515 ---description : "Supervisor IV with 2 1000BaseX GBIC ports"). I can see that on each supervisor engine i have two 1 GB SFP ports available and if i calculate for two supervioser engine i will have 4 1GB ports.
But at particular time only one supervisor engine is active and other is in standby mode (redundancy mode used is SSO between two SUP engines).
Can i used all 4 SFP ports for connecting 4 uplinks to the 4 access switch?Will all the 4 SFP ports active at one time or only 2 SFP ports will be active that is for only active supervisor engine.
View 10 Replies
View Related
Jun 4, 2012
I was upgrading IOS on 4507 R with dual supervisor.I download the IOS on Active supervisior and did reboot.After reboot i login to switch then i got switch standby prompt.I found that after reboot active supervisior became standby supervisior.
Now new IOS is on standby supervisior.Need to confirm below..So this means that IOS does not syn within the supervisiors as compared to config right ?
-Which command i can use that will copy IOS from standby supe to Active supe??
-Which command i can use that will show both active and standby supe with new IOS?
-Is there any command that i can use to switchover from active to standby supe??
View 3 Replies
View Related
Oct 30, 2012
After rebooting a pair of 6504's configured for vss, both switches show active on the sup modules. A show switch virtual redundancy however shows the pair working in an active/standby mode. We have 6509's in vss pairs and they show active on switch1 and standby on switch2 led's. For the 6504's switch 1 was booted first and then the second switch about 30 seconds later. Is there something different with the 6504's? [code]
View 4 Replies
View Related
Nov 20, 2012
Normally when we do HSRP with vPC on N7K the device will be Active/Standby in control plane but it will be Active/Active in data plane. In this case any traffic reach to standby device it can forward traffic directly to uplink which is not my desire. My goal is all traffic should pass through active (control plane) device in every case unless active device totally dead. So Is it possible for Nexus 7000 to be HSRP Active/Standby in Data Plane ?
View 4 Replies
View Related
Jul 17, 2012
I have a pair of ASA 5520s operating in failover pair as active/standby, having two contexts on them. I am planning to share the load and make it active/active making first context active on the primary unit and second context active on the secondary unit. My question is if this will disrupt any connectivity thru these firewalls when I do "no failover" on the active/standby and assign the contexts to different failover groups and enable the failover back.
View 6 Replies
View Related
May 15, 2012
we need to install a line cards (WS-X4548-GB-RJ45, chassis WS-C4510R-E), on a chassis Ws-6504-E.where I can find information about compatibility?
View 2 Replies
View Related
Apr 10, 2011
I faced one problem in our core switch 4507 R . Active sup lost connection and standby came active. We got lot of errors/alerts on console shown below. [Code] Also when I reloaded the switch with reload command only both sups got reloaded but I want to reload all the modules but reload command do not gives any options for that.
View 2 Replies
View Related
Feb 15, 2012
We are facing issue of having minor error for SUP module details below,SUP: WS-X45-SUP6-E see the minor error coming while troubleshooting this SUP 6-E error as below,
module 3: SerialNo :
Overall diagnostic result: MINOR ERROR#
Test results: (. = Pass, F = Fail, U = Untested)
1) supervisor-bootup ---------------> U
2) linecard-online-diag ------------> F
View 5 Replies
View Related
Nov 15, 2011
A client asked this question. Below is how I responded:
Q: Will the NFFC for the 4500 series work with a SUP6-E/SUP6-LE?
A: NO.
I have never attempted to install one on a SUP6-E, but there is no documented capability of that SUP to do netflow, either natively or with a daughter card. I can NOT however find any explicit documentation stating it will not work – only lack of documentation stating it will.
Specifically, it will or will not work? I suspect "no" based on how difficult it is to find either component on the same page, but I simply don't know.
View 1 Replies
View Related
Aug 30, 2012
Can 2 Cisco 4507E switches with redundant SUP6-E modules be connected togther using the the standard 10GB CX4 modules and CX4 copper cables? Are there any special modules or cables required.
View 1 Replies
View Related
Apr 8, 2012
I have a 4506-E with the following supervisor module:WS-X45-SUP6-E
It currently has 2 TwinGig converter modules installed. I want to upgrade the 2 1Gb connections to 2 10Gb connections. First I took out the converter modules and installed 2 X2-10Gb-SR's, but it didnt recognize ("No X2 GBIC")???
Then, I put the converter module back in and put two SFP-10GB-SR's in them, but they don't recognize either...???? I"m running IOS
12.2(54)SG1.
According to the 10Gb matrix, they should work:
Catalyst 4500 series
#(continued)
#WS-X45-SUP6-EWS-X4606-X2-E
##X2-10GB-CX4X2-10GB-LX4
#X2-10GB-LRX2-10GB-SRX2-10GB-ERX2-10GB-LRM
[Code]....
View 2 Replies
View Related
Dec 22, 2012
I notice that NAT is not possible Cisco Catalyst 4500e series. Is there any other ways to configure NAT? Currently we have 2x Catalyst 6509 and we're migrating to the 4510e and there's NAT in the 6509s. I was thinking of re-using the 6509s and connect to the 2 new 4510e in a meshed trunking layout with MST (Layer 2) and OSPF/EIGRP (Layer 3) protocols turned on.
View 1 Replies
View Related
Feb 11, 2012
I am trying to figure out the Flexible Net-flow on Cat 4510R+E Switch running IOS-XE code. My Neflow flow software is manageengine 7.X. I am able to see the netflow interfaces but the traffic itself is not displayed. On the Switch I can see the netflow exporter statistics counter being incremented thereby confirming as being exported.
View 2 Replies
View Related
Mar 13, 2013
we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 Replies
View Related
Jan 21, 2008
We have a new building, and I told the cable company run OM3 cable from second floor to 1st FL data closet because we have 4510R SupV-10G at each floor.However, the cable company ran a regular fiber cable instead of OM3 mistakenly. My questions, can I still use OM3 patch cable?? Second questions, can I still have the 10Gig performance??
View 3 Replies
View Related
Jan 28, 2013
I have a two Cisco 4510R each with two sup V-10GE redundant. The code on these sup modules are 12.2(31r)SG3. I need some assistance in getting this setup worked out. I have all four of the 10GE populated with appropriate optics. I setup a link from one 4510R to the other using these interfaces. From the documentation I found I had to use Tengi1/1 and Tengi2/2 as the redundant pair. I plugged the up link into these ports. The Tengi1/1 (active supervisor) links up and works fine. But when I look at the ports port Tengi2/2 it isn't showing link or active. Now port 2/1 (nothing plugged into it) is showing as active.
Now is the redundancy supposed to be 1/1 and 2/1? If so, the switch is in production, when I move the connection over from 2/2 to 2/1 will it cause a outage? The reason for this is I now have a system with a 10G port and would like to utilize one of the other 10G ports. Is that possible? Or does it have to be a lag/redundant up link to work (say to another switch)?
View 2 Replies
View Related
Sep 22, 2011
I'm working on deploying a new 4510R+E for our organization. This is my first experience with a modular switch. I'm trying to enable SSO, however in the redundancy configuration mode, the sso command is not available. Is SSO only available with certain software images / licensing levels? [code]
View 2 Replies
View Related
Jun 10, 2012
I am working on a network which has two ISP connections (Active/Active) terminating on router (ASR1000). From the LAN side (6500 switch) all the traffic need to be route on ISP1 but some of the specific subnets like 10.250.0.0/16 need to be route on ISP2 connection.
I am planning to use PBR and NAT with route maps. any documents or refrences are provided.
(access switches)---------(core switch)----------(routers)----------------(ISP1)
----------------------(ISP2)
View 1 Replies
View Related
Dec 13, 2011
We have cisco 4510R+E switch with IOS-XE Software Version 03.01.01.SG RELEASE SOFTWARE (fc1).Our this switch is having two core & one core is always going to about 90% to 98% cpu utilization while other core is showing normal (about 5% to 10%),we check with-This switch is gateway of our LAN.
View 6 Replies
View Related
Sep 10, 2012
We have recently purchased Catalyst 4510R-E with two PoE line cards. When we connected Cisco Wireless APs to Cat4510 PoE ports it did not come up. These WAPs are working fine on other Cisco switch with PoE ports so there is no issue with WAP. We have received two CAT4510 and on both two slots are populated with PoE line cards and on both switches WAPs are not coming up. PC/desktops are working fine on these ports.Is there any configuration required on Cat4510 to enable PoE feature.
View 15 Replies
View Related
Apr 2, 2013
We need to move some line cards around on our 4510. The top slots have a 24Gbps backplane while the lower slots are limited to 6Gbps. Poor planning on our part has left us with installing a 10Gb line card in one of the bottom slots. I'd like to move a couple of the cards up top, to the bottom.
My question is simply will the switch magically preserve the configuration for those cards and change the slot number for me or will I need to reconfigure the interfaces for those cards I move?
View 2 Replies
View Related
Sep 23, 2012
We have CORE switch model : Cisco WS-C4510R-E with dual SUP 5 - 2 10GE. [code] Now We want to upgrade this IOS to the upgraded version.
View 3 Replies
View Related
Feb 4, 2013
I have a requirement to upgrade some line cards in our 4510R-E chassis to ease some oversubscription due to the 6Gbps limit.
At the moment my plan is to upgrade three cards from WS-X4548-GB-RJ45 to X4648 to get the 24Gbps per card.
Supervisors are 6-E
1. Is this a viable plan?
2. If so can the cards be hot-swapped?
3. Would the new cards retain the existing interface settings of the previous cards?
4. Any gotchas to look out for?
View 4 Replies
View Related
