A customer wants to get the back-plane load of a cat4506-e chassis with a sup6-E supervisory card.A would like to check how many bus are used on the backplane and if the command "sh envi chassis" is the good and only command to be used ?I'm not sur that there is only one bus on the cat4506-E as with a sup7 card the backbone speed can change.
View 2 RepliesCurrently I have a Cat4506 chassis with a Sup II+ engine and one WS-X4232-RJ-XX linecard with the WS-U4504-FX-MT daughtercard to provide uplinks to four Cat2955 switches. I chose the Cat2955 because the switches are in an industrial facility and they fit the envrionment very well. Each of them has a multimode fiber uplink.
The issue I have now is that I need to add at least 4 more Cat2955 switches to the topology and find that the x4232 is EOL. I can always find a used one somewhere, but is there another currently shipping linecard that will do the trick? I see there is WS-X4248-FE-SFP with the 100BaseX interfaces, but don't really need 48 ports, just 8.
Is there another linecard that can downswitch a 1000BASE-X port to 100Base-X, or can I use a 100Base-X SPF in a switch like the WS-X4448-GB-SFP?
What are my options, aside from buying another X4232?
I have cisco 4510R L3 switch with installed 2 Sup on slot 5 and 6. the current active Sup is in Slot5 i want to make active Sup6 in slot 6 which is currently standby sup in chassis. Is there any way to make standby Sup to ACTIVE without reloading any of the Supervisor. however there is two way as per my understanding -
1. we can reload the active Sup so that standby Sup will take charge. - (redundancy reload shelf)
2. we can focefully switchover the state of Sup's by (redundancy forcefully swithover) but in above both cases reload will be performed by one of the supervisor. which i don't want.
What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?
View 1 Replies View RelatedHow can i get information about the back plane utilization. is there any command for the SB-switches (sg300).
View 2 Replies View RelatedWe currently have a WS-C6506 chassis with a line-card WS-X6408A-GBIC. Currently we need to replace the chassis by a Ws-6504-E and also the line-card. My question is: What must buy line-card and meets the same specifications of WS-X6408A-GBIC?.
View 4 Replies View RelatedI need to pull a WS-X4712-SFP+E line card from an online 4507 chassis, can this be done, or does it need to be offline?
View 2 Replies View Relatedwe need to install a line cards (WS-X4548-GB-RJ45, chassis WS-C4510R-E), on a chassis Ws-6504-E.where I can find information about compatibility?
View 2 Replies View RelatedWe are facing issue of having minor error for SUP module details below,SUP: WS-X45-SUP6-E see the minor error coming while troubleshooting this SUP 6-E error as below,
module 3: SerialNo :
Overall diagnostic result: MINOR ERROR#
Test results: (. = Pass, F = Fail, U = Untested)
1) supervisor-bootup ---------------> U
2) linecard-online-diag ------------> F
i need to upgrade my cat4506 with sup7L-E engine to latest ipservices software. link of suitable software and upgrade methode?
View 2 Replies View RelatedA client asked this question. Below is how I responded:
Q: Will the NFFC for the 4500 series work with a SUP6-E/SUP6-LE?
A: NO.
I have never attempted to install one on a SUP6-E, but there is no documented capability of that SUP to do netflow, either natively or with a daughter card. I can NOT however find any explicit documentation stating it will not work – only lack of documentation stating it will.
Specifically, it will or will not work? I suspect "no" based on how difficult it is to find either component on the same page, but I simply don't know.
Can 2 Cisco 4507E switches with redundant SUP6-E modules be connected togther using the the standard 10GB CX4 modules and CX4 copper cables? Are there any special modules or cables required.
View 1 Replies View RelatedI have a 4506-E with the following supervisor module:WS-X45-SUP6-E
It currently has 2 TwinGig converter modules installed. I want to upgrade the 2 1Gb connections to 2 10Gb connections. First I took out the converter modules and installed 2 X2-10Gb-SR's, but it didnt recognize ("No X2 GBIC")???
Then, I put the converter module back in and put two SFP-10GB-SR's in them, but they don't recognize either...???? I"m running IOS
12.2(54)SG1.
According to the 10Gb matrix, they should work:
Catalyst 4500 series
#(continued)
#WS-X45-SUP6-EWS-X4606-X2-E
##X2-10GB-CX4X2-10GB-LX4
#X2-10GB-LRX2-10GB-SRX2-10GB-ERX2-10GB-LRM
[Code]....
I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-
kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled: AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712 <====
I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-
atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?
I have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?
View 1 Replies View RelatedI have 2650XM router and 2620 Router Both routers have built in WIC T1 CSU/DSU cards
2620Router --
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: DTE side
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
[code]....
My question is that cisco website says there are two type of cable connections for this type of config --which are --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable it did not work.So for this type of connection i know i need T1 cross over cable-- which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over -- will this cable work in my router to router connection.
I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .
View 1 Replies View RelatedCurrently have a pair of 6509 chassis setup with VSS. Only have the Sup and two line cards in each chassis. Would like to replace with a new pair of 6504E chassis. Is it possible to fail one chassis at a time and migrate to the new 6504E?
View 3 Replies View RelatedI have PAT set up successfully on 6506 chassis - My outside address range is 78.24.112.114 255.255.255.240.Relevant parts of the config below: [code] This works fine but of course is only using the one IP address 78.24.112.114.how I can utilize the other outside addresses available or is this not really necessary? I've browsed through loads of Cisco docs.
View 2 Replies View Relatedwhy is not possible to put a WS-X4712-SFP+E - module into an R-E chassis?The module has the same connection to backplane as the WS-X4748-UPOE+E and this one works in a R-E chassis.I know the restriction of Cisco that the 4712 is only supported in 4503-E, 4506-E,4507+E and 4510+E, but why?Are there hardware-restrictions, is the backplane different?
View 2 Replies View RelatedWe are preparing to install a new switching Infrastructure at one of our sites. We have decided that we want to have two separate chassis as a core. My original idea was to purchase 2 - 4500 chassis and install 10Gb and 1GB line cards in each and use STP and HSRP to load balance between the two cores.
We had also contacted a vendor for thier recommendations and they came back with 2 6500 Chassis running VSS. I reviewed what VSS was as I had never heard of it and it looks to me basically to be real close to the same thing as Stacking. I didn't really want to have stacked Cores because I would like to have the flexibility to be able to take one core out and update the software or image, reboot, and such without effecting anything on the network. I can do that with the non-VSS approach but it looks like that would be more of a problem with VSS.
My question is, how to use VSS with the 6500's? How to take one of the VSS pairs off line and not effect normal network operations?
Configuring a 4507R classic chassis with redundant Sup 6L-E? TAC told me the Supervisor 6LE was only supported on the 4507R+E or 4507R-E chassis but I have found in Cisco documentation several places that indicate that the Sup 6LE is supported in the classic chassis.
View 1 Replies View RelatedI have 4506 chassis whose sup engine is WS-X45-SUP6L-E and recently brought line card WS-X4648-RJ45E. When i inserted very same line card on chassis is not support.
View 3 Replies View RelatedEvery one i want to know ws-c4503E series 3 -slot chassis . I have compatibility issues with MEM-C4K-FLD64M AND S45EIPBK9-12240SG will work.
View 2 Replies View RelatedWe have a backup sup 720 which has a 2 gigabit ethernet though port channel, to another chassis. Suddenly UDLD detected an error and got into err disable, then this err disable didn't let the interface set to DOWN, and created a switch loop, then our Supervisor reloaded. I'd like to know what could have caused this reload. In my opinion could have a been the switch loop, but also I've been checking from the output interpreter the show tech and might have been a bug, the only one that could match in IOS version 12.2(33)SXH, is this one: url...
We're going to disable err-disable next time I guess and recover the link manually, apart from that what could have made the sup for crash and reload?
Can any share some useful links on how this works and how to configure it? Do you still need to configure FHRP or does configuring redundancy take care of active/standby relationship between the ASR's?
View 2 Replies View RelatedI have an alert from monitoring system about: “ fan for this system is not in the NORMAL state”. In the switch I found that the problem is with fex 3, see below:
Nexus5020# sh env fex 3 fan
Fan Fex: 3:
------------------------------------------------------
Fan Model Hw Status
------------------------------------------------------
Chassis N2K-C2148-FAN -- failure
PS-1 N2K-PAC-200W -- OK
PS-2 N2K-PAC-200W -- OK
Technician said: fans appear to be operational, BUT the only thing that appears abnormal is STAT light is amber (not sure what it means).
Also, if I compare the temperature from module 3 with module 2 (which doesn’t have an alert) is almost the same, this is why I think the fan is working fine, since module 3 is not hotter that module 2.
What I can do to reset this fan (chassis)?
swapping out a failed supervisor card on a 6509 chassis?
View 6 Replies View RelatedI have 4x 3110x switches in a Bladecenter H chassis and the stack cables are connected so that they are in a circle (IE, SW1 connects to SW2, SW2 connects to SW3, SW3 to SW4 and SW4 to SW1). Each of the switches physical 10GE port is trunked to a 6509. If I pull a 3110x switch out, does this network connectivity? Theoretically it should not?
TK2EWRBC4SW01#sh switch neigh
Switch # Port 1 Port 2
-------- ------ ------
1 4 2
2 1 3
3 2 4
4 3 1
we have some pairs of 6509-VSS, which partially have old (no more officially supported) 6509-Chassis.All linecards in the VSS are the same (Sup 720-10GE-3C, 67XX).
We now bought some new 6509-E-Chassis and want to change the old chassis by the new ones in a ISSU manner, that means:
1. putting the partner, which chassis changes, in redundancy mode, switch it off, exchange chassis (old "Catalyst 6509", new "Catalyst 6509-E")
2. inserting the line-cards exactly in the same slots and connecting all cables
3. switch on the new chassis, witing to come up in VSS
I'm not sure of having to set the switch number for VSS (is that in the Sup?; configuration? or part of the chassis-memory?)
I've looked up cisco for some hints, but don't found anything.
Are there any physical characteristic differences between the 6509 and 6509-E chassis?
View 4 Replies View RelatedI have multiple 6509 vss switch. and i notice when the standby chassis reboot I didn't get any snmp trap, but I got when the active one reboot. my question is is there any mib out there for detecting and got a trap when standby reboot?
View 2 Replies View RelatedClient has Cisco 4507R+E chasis with SUP- 7L-E and he has WS-X4418-GB line card in stock can this line card work with E series chassis
View 2 Replies View Related