I have 4506 chassis whose sup engine is WS-X45-SUP6L-E and recently brought line card WS-X4648-RJ45E. When i inserted very same line card on chassis is not support.
View 3 Replies
We bought a Cisco line card WS-X4648-RJ45-E for Cisco 4507 R-E. Later on I found that this module is not working with the chassis becuase supervisor engine 4 we are using. Supervisor Engine 6 is required for WS-X4648-RJ45-E. Now I want to go for WS-X4548-RJ45. Is it possible to return the line card? Is there any possible way to exchange?
View 6 Replies View Relatedwe need to install a line cards (WS-X4548-GB-RJ45, chassis WS-C4510R-E), on a chassis Ws-6504-E.where I can find information about compatibility?
View 2 Replies View RelatedWe currently have a WS-C6506 chassis with a line-card WS-X6408A-GBIC. Currently we need to replace the chassis by a Ws-6504-E and also the line-card. My question is: What must buy line-card and meets the same specifications of WS-X6408A-GBIC?.
View 4 Replies View RelatedI need to pull a WS-X4712-SFP+E line card from an online 4507 chassis, can this be done, or does it need to be offline?
View 2 Replies View RelatedI have cat4500 with subject module. There is strange behaviour over module installed in 3rd slot only, some ports are connected, UP & working fine. But If I am connecting new ports over same module, are not coming UP.Duplex/speed settings already checked & are fine. If i connect same machine to any other module, it perfectly comes up & operation is fine.
View 3 Replies View RelatedI want to enable jumbo frame con a Catalyst 4500, specifically in the WS-X4648-RJ45-E card. (running this IOS version Version 12.2(53)SG1).
For what I checked, this are the only needed commands:
vlan xxx
mtu 9000
interface port 4
mtu 9000
exit
I want to be sure that these are the only needed comands and that they won t generate any disruption.
I have a heck of a time finding this kind of information on the cisco site...Is the WS-SUP720-BASE line card a fully supported module in the 6509-E chassis?
View 4 Replies View RelatedI just got a DSL Modem router (DSL 2750U) which has DSL input for internetconnectivity.My internet service provider provides RJ45 Cable which needs LAN input socket on a router for internet connectivity. How do I connect?
View 4 Replies View RelatedI have internet line came from my neighbor throught his hub directly connected to my laptop.. My problem is, i buy wireless ADSL model router but when i check the DSL line port its rj14 which i can not connect my RJ45 internet line. Addtional information, my wireless router have another 4 port LAN. Can i connect my internet line to LAN port,if it so how will i configure the router..
View 1 Replies View RelatedClient has Cisco 4507R+E chasis with SUP- 7L-E and he has WS-X4418-GB line card in stock can this line card work with E series chassis
View 2 Replies View RelatedI have a number of existing 4506 chassis type switches (the older non -E version) that I would like to roll out IP phones to. Instead of replacing the entire chassis, I would like to just replace the line cards in the switches with WS-X4548-GB-RJ45V. What or how much power supplies should I have in each switch to be able to power the 5 poe line cards (each port per line card will power an ip phone)?
View 6 Replies View Relatedhow much difference does it makes if i install a NIC PCIe card instead of using the MotherBoard LAN RJ45 for DSL PPPOe internet access?how much does a NIC lowers the latency?
View 3 Replies View Relatedi am getting internet from someone by a LAN cable. the lan Cable is connected to my LAN Card (RJ45).i bought a IPAD. and i want to browse using IPAD. IPAD needs Wifi connectivity. can i convert this existing setting to browse internet from my IPAD?
View 1 Replies View RelatedI would like to know whether WOL is supported on a N7K with 6.x code and F2 line cards. I also would like a how to for this. If it is not supported will an ip helper address to the broadcast address of the destination vlan SVI will suffice to get it workinng. If so I can restricht the forwarded broadcast to only the wol traffic.
View 1 Replies View RelatedI need a 10G support on 4503 chassi with SUP II plus TS.Is any of the 10G line cards i.e. 4712 or 4606 supported on SUP II plus TS on 4503?
View 4 Replies View RelatedIf you hot swap a 100M card with a Gig module in a live 4500 switch, what happens to the running-config? Don't have the module versions to hand.
View 2 Replies View RelatedI wonder are 4500-E series line cards (i.e. WS-X4648-GB-RJ45, WS-X4748-UPOE+E and WS-X4606-X2-E) supported on 4507R chassis? Datasheet says "Classic line cards may be deployed in both classic and E-Series chassis with either classic Cisco Catalyst 4500 Series supervisor engines or with the Cisco Catalyst 4500E Series Supervisor Engine." But it says nothing about E-Series line-cards being (or not) supported on classic chassis (like 4507R).
View 3 Replies View RelatedA customer wants to get the back-plane load of a cat4506-e chassis with a sup6-E supervisory card.A would like to check how many bus are used on the backplane and if the command "sh envi chassis" is the good and only command to be used ?I'm not sur that there is only one bus on the cat4506-E as with a sup7 card the backbone speed can change.
View 2 Replies View RelatedIf it is, can you point me to the correct drivers page as I cannot find it.
View 1 Replies View RelatedI would like to know if WS-x4612-SFP-E card is support in ciscoview ? If not, when it will be support ?
View 4 Replies View RelatedLaptop Fujitsu with Wifi adapter : Atheros AR9285 , lastest driver v10.0.0.52 April 2012
Win 7 32bit pro WLC 6.0.196.0 and AP 1142 , associated in 802.11G or N WPA 2 preshared key.
WLC Roaming parameter : minimum RRSI -80dbm, roaming hysteresis 2dB, adaptive scan threshold -70dBm, transition time 5sec.
The laptops are supposed to be compatible with CCXv5 program, but in WLC (and two controllers CT-5508) the client is not seen as CCX client compatible !
So roaming is bad. Even with a very good and dense wifi coverage (no coverage hole detected), because the laptop still stay associated with a far AP (until -90dbm), instead of roaming with the nearests APs (-40dbm !!)
Im looking for MIB for monitoring 6500 line card from availability prespective;
View 1 Replies View RelatedI see differrent voltage in line card ws-6704. Iam afraid of something went wrong with my 6500 switch. two 6500 switch is redundant.
View 3 Replies View Related[code]...
Primary clock is CSC 1 Board State is Waiting to retry download after persistent failures (RTRY WAIT) Insertion time: 00:00:16 (13:54:07 ago)
Im wondering if the Adaptive Security Services Module has some of the same function as a ASA 5500.Can we configure a IPSec VPN tunnel, SSL VPN tunnel or IPS on a C6500 with ASA-SM or do we need a specific line card for those tasks?
View 1 Replies View Relatedmy office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies View RelatedI urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?
View 1 Replies View RelatedCisco Catalyst 6509 Chassis.We have moved a line card from slot 8 to slot 6, but config remains for the line card in slot 8 and nothing is seen in slot 6.
We are running on IOS Verison 12.2 (33SXH2A) i.e. VSS.Blade model number is WS-X6748.
when replacing a line card on a 6500, i gather there is no config stored on the card, its all held on the sup, so when i put in another card the config will be the same?
View 2 Replies View RelatedI am trying to configure traffic policing on a 7609 with ES20 line card - however it doesn't appear to be working. The customer is randomly getting DoS attacked, and the policy doesn't appear to be dropping any exceed/violate traffic.This is an egress policy on a sub-interface.
View 5 Replies View Relateddirect me to a document detailing the order that line cards are supposed to boot in a 6500? I'm noticing random boot sequences in some of my chassis,?Note: We currently run Sup720 3CXL for the most part.
View 6 Replies View RelatedThe WS-X68xx series line card has a fabric of 40Gbps and a 16 Port 10GE has a 4:1 oversubscription rate. The WS-X6908-10G has a fabric speed of 80Gbps and has a 1:1 oversubscription rate.
If I mixed the 68xx and 69xx series line card, do I get 80Gbps for the 6900x and 40gbps for the 68xx line card? Or would the 69xx series line card be downgraded to 40Gbps?
From my understanding, the 68xx series has a DFC card and thus the fabric speed operates independently.
