I have a heck of a time finding this kind of information on the cisco site...Is the WS-SUP720-BASE line card a fully supported module in the 6509-E chassis?
View 4 RepliesWe've just invested in a pair of Sup2Ts to upgrade a Sup720 6509 chassis but I'm unsure exactly how the management port(s), aka the Connectivity Management Processor (CMP), should be configured (and patched) in a dual supervisor system?Is each CMP an independent entity or is the management interface configuration (IP address, gateway, etc) replicated between supervisors?If it's the latter then do both management ports need to be physically connected at the same time?
View 1 Replies View RelatedWe recently purchased 2 Cisco 6500 series switches (with Sup 2T). These switches will be replacing our old 2 6500 series switches (with Sup 720).
We have 70 vlans and 90+ closet switches (2900) connecting the core switches We have 2 WLC connected to the core switch. We also have a 1 x 1 connection to a VSS switch which in turn connects to our Server Co-Location data center utilizing IPSec & GRE tunnel to connect to our Server Co-Location data center.
Our routing protocol is EIGRP. Our VTP domain at Server Co-Location is separate from our location “A” campus. I was wondering what is the best way to migrate our Core switches at location “A” campus.
The requirement is we would like to replace these switches with minimum downtime.
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
Currently have a pair of 6509 chassis setup with VSS. Only have the Sup and two line cards in each chassis. Would like to replace with a new pair of 6504E chassis. Is it possible to fail one chassis at a time and migrate to the new 6504E?
View 3 Replies View RelatedJust a very quick one. Is there any physical limitation to how many ARP entries a 6509 and sup720 can have?
View 4 Replies View RelatedWe have a backup sup 720 which has a 2 gigabit ethernet though port channel, to another chassis. Suddenly UDLD detected an error and got into err disable, then this err disable didn't let the interface set to DOWN, and created a switch loop, then our Supervisor reloaded. I'd like to know what could have caused this reload. In my opinion could have a been the switch loop, but also I've been checking from the output interpreter the show tech and might have been a bug, the only one that could match in IOS version 12.2(33)SXH, is this one: url...
We're going to disable err-disable next time I guess and recover the link manually, apart from that what could have made the sup for crash and reload?
swapping out a failed supervisor card on a 6509 chassis?
View 6 Replies View Relatedwe have some pairs of 6509-VSS, which partially have old (no more officially supported) 6509-Chassis.All linecards in the VSS are the same (Sup 720-10GE-3C, 67XX).
We now bought some new 6509-E-Chassis and want to change the old chassis by the new ones in a ISSU manner, that means:
1. putting the partner, which chassis changes, in redundancy mode, switch it off, exchange chassis (old "Catalyst 6509", new "Catalyst 6509-E")
2. inserting the line-cards exactly in the same slots and connecting all cables
3. switch on the new chassis, witing to come up in VSS
I'm not sure of having to set the switch number for VSS (is that in the Sup?; configuration? or part of the chassis-memory?)
I've looked up cisco for some hints, but don't found anything.
I support an active VSS cluster using 2 x 6509E chassis with single Supervisor 3C modules in each chassis. I want to replace these with Supervisor 2T modules. All my service modules and line cards are supported with the Sup2Ts (I will also be implementing 6908 modules). Is there a document on the Cisco site for this? I haven't found one though I can find plenty that describe how to do a software upgrade.
(Note, I have a 3rd (non VSS) 6509E chassis that is also part of this core network and that will maintain VTP/V LAN's etc).
Are there any physical characteristic differences between the 6509 and 6509-E chassis?
View 4 Replies View RelatedI have multiple 6509 vss switch. and i notice when the standby chassis reboot I didn't get any snmp trap, but I got when the active one reboot. my question is is there any mib out there for detecting and got a trap when standby reboot?
View 2 Replies View RelatedAny have experience on triggered failover on VSS deployment with 1 VS-720-10G-3C in each chassis? I tried using "redundancy force-switchover" but after that the 20G VSL is flapping up & down and cannot be up normally, we got 1 FWSM in each chassis, any configuration need to fit in this kind deployment? BTW, if I shutdown the power source of VSS active chassis, both FWSM & VSS can failover normally.
View 3 Replies View RelatedI'm fairly new to networking and need to migrate an old core to a new core. I have a 6509-e Switch that I had an RMA on one of my 720 sup cards. After receiving the sup card I swapped my slave out with the new one, expecting it to boot into ios. It booted into Roman. I tried to boot the image manually and it did the same thing. I also tried to boot from my flash and, again, booted into ROMmon.
Question: If i configure and change the boot to boot from image it tells me i need to reset or power cycle first. Will this reset the entire switch? As this is production I'd rather not.
I am at home now, but I can supply any logs/hardware model/configs tomorrow. I thought I would see if this is an easy fix.
I have a two fiber connection from our Central Office(6513) to Remote office (6509). I have a requirement that on the remote office if one of the fiber goes down, the second fiber should work as a failover. I am planning to use SUP720-3B SFP to connect to the CO.
Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G5/2? or Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G6/2? I am running EIGRP between sites. Any sample config.
sup-bootflash:s72033-pk9sv-mz.122-18.SXD7b.bin"
setting up VRF-lite on redundant 6509-E chassis to account for chassis failure? Let's say I have 2x 6509-Es configured with HSRP for 2 vlans, ServerA and ServerB. So
6509-A#
!
interface Vlan10
description ServerA VLAN
ip address 10.10.10.2 255.255.255.0
ip flow ingress
standby 1 ip 10.10.10.1
standby 1 priority 105
[code].....
I now need to create an environment where the Server VLANs can be provided for two customers and they need to be wholly separate. On 6509-A, I make VRF CustomerA and VRF CustomerB and I assign Vlan10 to VRF CustomerA and Vlan20 to CustomerB. Do I create the SAME VRFs on 6509-B with the same logic?
We are trying to migrate from 1g to 10G, couldn't find any module on 6509-E which supports 10G on SFP+ ...I can see X2 and Xenpacks .. but not SFP + .what exactly this Xenpack means ?
View 3 Replies View RelatedI recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.
The 6509 Series Switches support the scenario VSS Active-Active Chassis, I would like to setup both switch's as one virtual switch but working at the same time, not with Active - Stand By Chassis.
My plans it to create PortChannel accross both Switches 6509 in order to have 2 links one connected to one slot/switch and the other connected to slot/switch in the second 6509 for servers redundancy.
we need to install a line cards (WS-X4548-GB-RJ45, chassis WS-C4510R-E), on a chassis Ws-6504-E.where I can find information about compatibility?
View 2 Replies View RelatedI have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
Policy Map VOIP
Class IP PHONE
priority percent 75
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..
1)For 3650X I found some contradiction in the Q&A about feature set LAN Base vs IP Base:
LAN Base: Can I do static IP routing ?
LAN Base: SVI => is this for intervlan routing ?
2)For 2960, there are 2 flavors (LAN lite and LAN BASE) Q: Can I do static routing on one of these flavors ?
I have a WS-C3750X-12S-S (IP Services) that I THINK I'd like to downgrade to LAN Base so I can stack it with a WS-C3750X-48T-L that is already LAN Base..
View 4 Replies View Relatedcan we upgrade 2960 switch from Lanbase IOS to IPbase
View 4 Replies View Relatedto the above question. I see the specs for the WS-SUP720-3B and 3BXL but not the WS-SUP720-BASE with the MSFC3 and PFC3A daughter cards.The 3B can handle 256,000 routes using IPv4 and the 3BXL can do 1,000,000.
View 4 Replies View RelatedCan the sup720b be used in any other slot on a 6513 besides 7 and 8?
View 1 Replies View RelatedThe table referenced in the new 1.1 ISE guide show 12.2(33)SXI6 is the minimum version for support. Does this mean this version or above? Does ISE is tested in newer SXJ streams? We have a massive rollout of SUP720s to do and need to know the most stable version to load in preparation for ISE.
View 1 Replies View RelatedI have 4506 chassis whose sup engine is WS-X45-SUP6L-E and recently brought line card WS-X4648-RJ45E. When i inserted very same line card on chassis is not support.
View 3 Replies View RelatedWe are looking into replacing our current Windows NLB configuration with a SLB solution as NLB creates some nasty multicast traffic.
We are currently curious about the limitations for running SLB without a dedicated ACE Module, will it handle line-rate speed (1 and 10 gbit) with SLB?
Does VSS introduce any limitations for SLB? Any other pitfalls/limitations we should be aware of?
Hardware info: 2x WS-C6509-E in VSS with VS-S720-10G (VS-F6K-PFC3C) running s72033-ipservicesk9_wan-mz.122-33.SXI7
Currently we do not have multicat routing enabled on either of our 2x Sup720-10G 6509 Switches. We have no intention of doing so either. I am looking for clarification on how mutlicasting operates within a Vlan.
IOS: s72033-ipservicesk9_wan-mz.122-33.SXH2a.bin
Our Vlan has IGMP snooping enabled. Here is the output.
6509Switch#sh ip igmp inter vlan 25
Vlan25 is up, line protocol is up
Internet address is 10.1.1.254/24
IGMP is disabled on interface
we do not want to disable IGMP due to this one concern that I can't find documented. If we disable IGMP snooping on the vlan, what happens to multicast packets with a TTL > 1. Do they get flooded to the entire switch and all Vlans? Or does it stay within the Vlan?
Need to remove the IPSec VPN SPA module from the 6509 chassis. Does the module is hot swappable or does the 6509 need to be turned off prior to removal.
View 2 Replies View RelatedI will be installing a secondary SUP720 in a 6509-E and will be upgrading the IOS on the existing SUP which is on 122-18.SXF6. I've read that this release has passed End of Critical Maintenance earlier this you. I thinking of upgrading the IOS to 12.2.33-SXJ1(ED) or 12.2.33-SXI8(ED) (possible more stable), but i'm not sure if i need any step upgrades from the current version. The SUP meets the required hardware specs and I will also be upgrading the ROMMON to 12.2(17r)SX7 first.
I have alot of experience upgrading IOS on routers and switches, but i just need to now if there are any gotchas that i need to know for the upgrade on the SUP.
The other issue is i don't believe the current IOS has been installed, are there any issue running on an IOS not installed. Patching is not available since the system is not running from an installed image. To install please use the "install file" command.