We are trying to migrate from 1g to 10G, couldn't find any module on 6509-E which supports 10G on SFP+ ...I can see X2 and Xenpacks .. but not SFP + .what exactly this Xenpack means ?
View 3 Replies
I have a heck of a time finding this kind of information on the cisco site...Is the WS-SUP720-BASE line card a fully supported module in the 6509-E chassis?
View 4 Replies View RelatedI recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.
I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
Policy Map VOIP
Class IP PHONE
priority percent 75
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
I have a 6509 and a 6506- same IOS version and flavor, same hardware, etc. One supports rate limiting on the VLAN interfaces, the 6509 says "not supported due to hardware". What is the difference here? Im very confused on this since I was under the impression the chassis were the same- just in size.
View 1 Replies View RelatedI have a 10Mbps connection link which I will like to reduce to 5Mbps on a 6509 switch as indicated in the config below. [code] After applying the service policy on the vlan interface, i got this "match vlan is not supported for this interface". I actually tried the rate limit command but I cant see the effect using the speedtest.
View 2 Replies View RelatedDoes the FWSM for a 6506/6509 is supported in a VSS environment?Also, does the FWSM work with the 2T supervisor module?
View 1 Replies View RelatedIs 'mls qos' supported on Cisco 877? I want to implement bandwidth limiting on a specific IP using access-lists on a class-map.If yes, what version and software do I need (ip base, adv security, etc)?
View 2 Replies View RelatedWhy does my 3750x-12s switch say it's not supported in CNA??? I upgraded to CNA 5.7.1 and still says unsupported. This device is supported or I'm just missing something.I use CNA heavily to manage our MANY vlans.
View 1 Replies View RelatedOn googling I came across documents that say OTV (Overlay Transport Virtualization) is supported on Cat 6500. Any authentic information whether OTV is supported on Cat 6500, especially with Sup-720B? FYI, Cisco Feature Navigator does not mention it.
View 1 Replies View RelatedDoes VPC is supported with WLC 5508? I am running 5.1.(3).
View 6 Replies View RelatedMAC Support: 16000
Backplane: 18Gbps
Forward: 28Gbps
VLAN's: 4000 (q-in-q support)
Jumbo Frame Supported
Supported 8000 static routing
!Supporting Stack!
Cisco 4948 supporting stackable? which product do you recommend to these criteria?
Whether Cisco Catalyst 4500-E with SUP 6E Supported vss?
View 1 Replies View RelatedHere i have a customer who has 7609 router with modules
ws-+6748-ge-tx
ws-svc-wism-1-k9
ws-sup720-3b
ws-sup720-3b
ws-svc-wism-1-k9
ws-6724-sfp
ws-x6704=10ge
ws-x6724-sfp
will this modules will be supported to the new chaisis ios or in the chaisis 7609S
I know the white papers say that the RPS 2300 supports the 3750-E series and the 3750 series, but we have 3750-G and -X series. Wanted to make sure that these switches are supported and if we need anything special?
View 3 Replies View RelatedFrom what I have found the VPN (WS-IPSEC-3) port adapter (on a WS-SSC-600) is not supported if you decide to turn the 6509-E into a VSS system.
View 2 Replies View RelatedDoes GLC-GE-100FX SFP is supported on the Cisco Catalyst 4928? Have tried the below link but it doesn't mention the 4900 series switches. url...
View 1 Replies View RelatedDoes GLC-GE-100FX is supported on the WS-C2960S-24TD-L. I don't see this switch listed under the compatibility matrix.URL
But the datasheet for the 2960S says this:
"The Cisco Catalyst 2960-S with SFP+ does not support the GLC-FE-100BX, GLC-FE-100FX, or GLC-FE-100LX." But it provides no reference for the GLC-GE-100FX The easy answer is, no the 2960S-24TD doesn't support it, any clarification if possible.
i want to know of the IOS verstion of cisco switch which support STP,some one told me that this feature is activated by deafalut if it not activated,how to turn on this Feature.i am using cisco 2960 Switch.
View 2 Replies View RelatedI am working in an environment where i have to use more etherchannels, any way that how many etherchannels could we create on Cisco Switch 3750 e. do they can utilize high process resources of CPU.
View 4 Replies View RelatedMy book says there are two types of firewall supported on cisci ios routers:
Classic cisco ios firewall
Zone-based policy firewall.
zone-based policy firewall with configurations ?
What kind of firewall is supported on Cisco PIX 515E ? Is it Classic CIsco ios firewall or Zone-based policy firewall ?
Does the X2-10GB-T copper transceiver is supported on the WS-X45-SUP6L supervisor?
View 1 Replies View RelatedSFP-10G-ER are not supported on Catalyst 3750-X and on other switches ....
%PHY-4-SFP_NOT_SUPPORTED: The SFP in Gi1/1/1 is not supported
Why ?When will ER be supported ?
Cisco c4948e switch log is showing :
COMPACTFLASHNOTREADY: Compact flash is not ready
Feb 24 00:28:22.338 UTC: %C4K_FLASH-4-COMPACTFLASHNOTREADY: Compact flash is not ready
COMPACTFLASHNOTREADY: Compact flash is not readyFeb 24 00:28:22.338 UTC: %C4K_FLASH-4-COMPACTFLASHNOTREADY: Compact flash is not ready
Checked the data sheet and is not supported. Why we get this log from the switch? is it cosmetic?
AME: "Linecard(slot 1)", DESCR: "10/100/1000BaseT (RJ45), 10GE (SFP+) Supervisor with 48 10/100/1000BASET ports and 4 10GE SFP+ port"PID: WS-C4948E , VID: V01 , SN: CAT1425S0NZ
NAME: "TenGigabitEthernet1/49", DESCR: "SFP-10Gbase-SR"PID: SFP-10G-SR , VID: V02 , SN: AGD132134ER
NAME: "TenGigabitEthernet1/50", DESCR: "1000BaseLH"PID: Unspecified , VID: , SN: FNS141203YF
[code]...
I would like to know whether WOL is supported on a N7K with 6.x code and F2 line cards. I also would like a how to for this. If it is not supported will an ip helper address to the broadcast address of the destination vlan SVI will suffice to get it workinng. If so I can restricht the forwarded broadcast to only the wol traffic.
View 1 Replies View RelatedI have a Cisco 1921 Router, a Cisco Catalyst 2960 and a Cisco Catalyst 2970 and I want the router to be able to assign ip-addresses by what VLAN a device is active on.
VLAN1: 10.0.0.0/24
VLAN2: 10.0.1.0/24
The router is connected to the Catalyst 2960 and there on to the Catalyst 2970 so the VLAN1 and VLAN2 is active on the to switches and the Router.is it possible?
What features are supported in the image ipservces cisco 3750X-24T-S? Need NAT
View 1 Replies View RelatedI need a 10G support on 4503 chassi with SUP II plus TS.Is any of the 10G line cards i.e. 4712 or 4606 supported on SUP II plus TS on 4503?
View 4 Replies View RelatedI'm trying to configure a SPAN session on a Cisco 3725 router, but it won't let me complete the command. The router has two Fast Ethernet interfaces: 0/0 and 0/1. I'm trying to configure a SPAN session with Fa0/0 as the source interface and Fa0/1 as the destination interface. [code] But when I try to configure the session, it seems like it's giving me the option to configure the SPAN session, but in the end the router won't let me: [code] When I type "?", why would it give me the option of using the Fast Ethernet interface as source port, then when I try to execute the command, it doesn't like it?
View 7 Replies View Relatedhow to identify which modules are supported by cisco catalyst 6500. is there any OID which can give us the information
View 2 Replies View RelatedI have a 3750 switch (c3750-ipbasek9-mz.122-46.SE.bin) were i want to add bandwitdh limit pr. interface, doing the following:
ip access-list extended customer_A
permit ip any any
class-map match-all BW_10Mbps
[Code]....
When i trie to apply the "service-policy output 10 Mbps" to the interface, it says the service-policy output is not supported on the switch. Is this a software related isue ?
