I have a Cisco 1921 Router, a Cisco Catalyst 2960 and a Cisco Catalyst 2970 and I want the router to be able to assign ip-addresses by what VLAN a device is active on.
VLAN1: 10.0.0.0/24
VLAN2: 10.0.1.0/24
The router is connected to the Catalyst 2960 and there on to the Catalyst 2970 so the VLAN1 and VLAN2 is active on the to switches and the Router.is it possible?
I will be installing two Cisco 1921 Routers to connnect a T1 between two offices. We are changing out our current AdTran routers as we would like to bridge three VLAN's across the T1 link. I followed the instructions at (URL) shtml to the best of my ability and my two Gigabit Ethernet ports are tied into a bridged virtual interface (BVI1). I then assigned a IP to BVI1 and another to my Serial0/0/0 then made a route to get to the other side of the T1 and a defualt route out our proxy. What I want to do now is setup QoS to make sure my voice data gets priority.
I setup a QoS ACL called "Voice" with the TCP and UDP source and destination ports that our phone system uses. I then setup a QoS policy on the Serial0/0/0 outgoing interface called "VoiceTraffic" and under the "match" list I match DSCP 46 or my "Voice" access rule. For the action I turned on "Queuing" and set it up for LLQ at 50%. Does this sound about right? Is there anything els eI can setup? I tried ot setup something else on the ethernet side but because they have the BVI I can't. I read some article sin this forum that said I could still apply QoS to the GigabitEthernet ports even if they are in the bridge group but it doens't let me do that.
I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies View RelatedWe have two Cisco 5505 firewalls connecting to two ISP's . The two internal LAN's on the firewalls are 192.168.184.0/24 & 192.168.186.0/24. We also have a Cisco C3560x layer3 switch with vlan interfaces 184.3 & 186.3. We have two DGS-3100 Dlink layer 2 switches connecting our users to the Layer 3. Ip routing is enabled for intervlan communication & I can reach the Switch interfaces & firewall gateways from machines on both on the vlans.We have pbr enabled on the 3560 & users only on the .186 network can get to the internet. The switch is running the ipservices license & the sdm template is "desktop routing" .
Users on the .184 cannot access the internet but we can ping the layer3 interface & the firewall gateway. [code]
Using Cisco 2960 series switches (Have 8 . 2 stacks of 4) to replace 6 old switches. 4 old switches had IP ranges of 192.168.6.*** and all new switches have 10.1.*.* addresses. Core switch has 10.1. as well as 192.168 ip addresses but i need to configure one vlan (5?) to route to 192.168 address. PC's on 10. address taking a long time to access 192 range.
View 2 Replies View RelatedI have a Cisco 2901 with the 4port gigabit ethernet switch module that I'm trying to get configured to have a seperate subnet for each port. So far I have it set up so each subnet is a vlan, then on each port I use the switchport access vlan command to tell it which subnet I want that port to be on. However, there is one port that I need to have 2 subnets on. The way I found to do that was to use switchport trunking on that port, but it doesn't seem to be working properly. how they would configure this? Right now I have vlan 101 as x.x.x.17/28 and vlan 103 as x.x.x.53/30. I think where I'm getting hung up is the proper association between the physical port and the vlan subnets.
View 5 Replies View RelatedWe're going to be switching some of our gear from Foundry to Cisco, and were looking at the WS-C2960S-48TS-L. We currently have 3 different VLAN's, and I wanted to have 1 uplink back to our firewall (ASA 5550) and then let the firewall do the routing between the subnets. I realize that 1 link will carry the traffic twice then, but is that possibly with those switches to have all three vlans assigned to one port and then just let the firewall do the routing between the vlans or would I need to have 3 uplink ports back to the 5550?
View 1 Replies View RelatedI would like to know if it is possible to assign a 3rd IP address to my end user vlan. Basically the 45xx acts as my end user gateway and has been confirgured as below
interface VlanXX
description Main Vlan
ip address 2.X.X.X 255.255.255.0 secondary
ip address 1.X.X.X 255.255.252.0
[Code].....
Here, due to IP address exhaustion in my end-user network, i want to add one more subnet X.X.X.X/22 to my network and assign one IP more from this range to the above vlan to act as the gateway IP.
We bought a pair of ASR 1004 to be installed at Primar & Secondary data center and one thing is to run OTV over it, but to do that, I have to extend multiple VLANs from my Core (Pair of Nexus 7010s) connected directly to the ASR is Primary Data center, I looked at some documents but didn't get a good idea about it, extend multiple VLANs from Nexus switch to an ASR.
View 2 Replies View RelatedI recently bought SG-300 28P to create the VLAN. My network hs 3 subnet 192.168.1.0, 192.168.2.0 and 192.168.3.0.My main net work is 192.168.1.0. I want to divide it to VLAN to eliminate the boardcast storm; especially from the domain 192.168.3.0
But I want all the devices from 192.168.1.0 to access other subnet.
We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability
delay down 1 up 1
!
track 20 rtr 2 reachability
delay down 1 up 1
ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
The field engineer has a stand alone 24 port 2900 series switch that he has different equipment connected to and are segmented using VLANs. So for example, he's got ports 1-4 assigned to VLAN 10, 5-12 assigned to VLAN 20, 13-19 assigned to VLAN 30 and 20-24 assigned to VLAN 40. He would like all the gear on VLAN 30 to have the ablity to talk to all of the other VLANS, but VLAN 40 should not be allowed to talk with any other VLAN. Trunking would do no good here since the switch isn't connected to anything and you can only assign one VLAN per port.
Is there a way to do this within the stand alone switch? The only possible way I could think of would be to ensure that each VLAN has an assigned IP number (subnet) and doing this through access lists.
I have a Cisco SG200 26 Port Switch, 2 Cisco WAP4410N Access points, and a VLAN aware Router. I have created 4 VLAN's. For the sake of this conversation lets call them.
98 - Intel Vpro
99 - Management
100 - General
101 - Guest
The Access points are capable of doing V LAN tagging so I plan on having them tag a guest network as V LAN 101. That can get sent to the V LAN aware router and out. No problem. I have some devices, or management pages that I don't want accessible from the general network. (Intel V pro KVM, Remote Management Cards, AP Config Menus, Switch config menu...) . I need to be able to take a V LAN unaware device, plug it into port 1, and have it communicate with V LAN 98, 99 and 100.
I asked this in the LAN forum but I don't think people understood what I was asking. I want to know if I can route VLAN's across my T1 point to point connection using 1921 routers. I currently have AdTran 3205's and although I found info on the internet saying you can make them do this I could not after many hours of trying. I also found this article: [URL] that also seems to say I can do what I want but I just want to verify.
We have two main locations currently connected by a point to point T1 (1.54Mbps) through the AdTran 3205's. We are running out of IP addresses as we just have a single subnet on each end. I want to move to a VLAN setup for a couple reasons including security and QoS for our voice system. Each location has it's own dedicated internet and proxy server. Here is my planned layout:
ISP 1 ISP 2 | | | | | | | 10.0.0.0/30 | Layer-3 Switch 1 -- 1921-1 ---------- 1921-2 -- Layer-3 Switch 2 | | | .1 .2 | | | | VLAN 20 | | VLAN 20 | | 10.1.20.0/24 | | 10.2.20.0/24 | | | | | VLAN 10 VLAN 30 VLAN 10 VLAN 3010.1.10.0/24 10.1.30.0/24 10.2.10.0/24 10.2.30.0/24 Building #1 Building #2
Can I do this with the 1921s? Is there a better design for what I want to accomplish (seperate our users, servers, and phones onto seperate VLAN's)?
I'm new to networking and was looking for some assistance. First off im using packet tracer to diagram my senario as I will be receiving my equipment next week to deploy.
Hardware to be used:
1. 2 catalyst 3560 switches
2. all connect to a sonic wall router
I have two companies that work in the same office space. I need to keep these companies seperate on their own vlan. They will however need to share the phone system.(Packet tracer file uploaded to give those who have the time to see what I put together.) [code]
how many SSL VPN Users are supported in Cisco1921-SEC/K9 routers? Or do i need to separately purchase SSL-VPN User license- FL-SSLVPN25-K9 (Cisco SSLVPN Feature License-25 Users) separately?
My client requires 25 Users SSL VPN.
I make qos on VPN Tunnel, but i make command service-policy output name, it show the error below Traffic Shaping feature is not supported in user defined class of parent level policy.My cisco router 1921, IOS : c1900-universalk9-mz.SPA.150-1.M5.bin
View 1 Replies View RelatedIs it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies View RelatedI have the following config using a Cisco 1921. I am trying to get devices on the the native VLAN to get internet access via the gateway x.x.x.73.Any thing being routed from the other Vlans 15/20/30 can get access, but nothing from an internal IP address. Is there something I am missing.
The Xs replace the same 3 octets for each interface.I am trying to route from VLANs 15/20/30 to see VLAN 5. I have tried a few things, in terms of adding extra ip routes, but can't get anything to work. Each of those Vlans have another router on the other side of them, which I have also tried adding ip routes too, but nothing. One of the routers (Vlan15 is a Draytek 2830). [code]
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
Is 'mls qos' supported on Cisco 877? I want to implement bandwidth limiting on a specific IP using access-lists on a class-map.If yes, what version and software do I need (ip base, adv security, etc)?
View 2 Replies View RelatedHow do I set a password? new Cisco 2911 router, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4 ?
View 6 Replies View RelatedI am setting up a new 1921 for a public library and I am running into a problem and I bet I am missing something simple. All the internal stuff works and I can ping the outside IP on the 1921 but can't go any further to the internet. The 1921 has the 2 gig ethernet ports, 0/0 is connected to a DSL getting DHCP settings fine from the DSL modem. The other gig ethernet port 0/1 is running the inside network and its function fine, I have a server on it and other clients and they can ping and get dhcp settings etc.I've pasted the config output below and IP addresses of the main actors. [code]
View 1 Replies View RelatedHow I can upgrade the iOS from CISCO 1921 ISR? Without losing my configurations.
View 3 Replies View RelatedI have already ordered a Cisco ISR 1921/K9. but as i read on Cisco website, it is written that Cisco 1921/K9 only support (IP SLA Responder) feature.
I don't know actually what is sla- responder. but our requirement is we will connect that Router 1921/K9 into 2-ISP links and i want to enable IP- SLA probes on that router so that it can track both the routes into those isp links. so my question is does CISCO 1921/K9 have the support for what i need ?How about Cisco 1921-SEC/K9 ?
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedI have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
I am looking to transfer 3 VLANS (10, 20, and 30) over a T1 point to point using Cisco 1921 routers. I do not want to "Bridge" the connection, one location has a 10.1.0.0/16 subnet and the other location has a 10.2.0.0/16 subnet because we don't want to saturate the already slow link.
I tried the instructions here: [URL] With these routers couldn't I create the three VLAN's then tell the GigabitEthernet0/0 interface it's a trunk port? Or do I setup sub interfaces (.10, .20, and .30) for each vlan? I've tried all of the above and I can't get it to work. I can directly plug into the router and ping the other router on the other side of the T1 but I can get the info coming from my Dell PowerConnect 6248 (plugged into a trunk port) to go through to the router which is why I think it's a vlan issue.
Why does my 3750x-12s switch say it's not supported in CNA??? I upgraded to CNA 5.7.1 and still says unsupported. This device is supported or I'm just missing something.I use CNA heavily to manage our MANY vlans.
View 1 Replies View RelatedWe are trying to migrate from 1g to 10G, couldn't find any module on 6509-E which supports 10G on SFP+ ...I can see X2 and Xenpacks .. but not SFP + .what exactly this Xenpack means ?
View 3 Replies View RelatedOn googling I came across documents that say OTV (Overlay Transport Virtualization) is supported on Cat 6500. Any authentic information whether OTV is supported on Cat 6500, especially with Sup-720B? FYI, Cisco Feature Navigator does not mention it.
View 1 Replies View RelatedDoes VPC is supported with WLC 5508? I am running 5.1.(3).
View 6 Replies View Related