Cisco Switching/Routing :: Connecting 2650XM - 2620 Router Back To Back WIC - T1?
Nov 25, 2011
I have 2650XM router and 2620 Router Both routers have built in WIC T1 CSU/DSU cards
2620Router --
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: DTE side
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
[code]....
My question is that cisco website says there are two type of cable connections for this type of config --which are --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable it did not work.So for this type of connection i know i need T1 cross over cable-- which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over -- will this cable work in my router to router connection.
View 5 Replies
ADVERTISEMENT
Dec 4, 2011
What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?
View 1 Replies
View Related
Apr 11, 2013
I have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?
View 1 Replies
View Related
Jan 27, 2013
I have a lab setup to take my CCNA and CCNP and I'm having issues trying to get WAN connectivity back to a switch at the end of my network. My lab environment consists of 1 - 2950 switch, 1 - 2620 and 1 - 2621XM. I have 1 Ethernet connection from each router to the switch and 1 serial connection from the 2620 to the 2621XM. I have the serial interfaces in a shutdown state right now so there is no loop since I do not have Spanning tree setup on the ports on the switch yet.
Right now using the fast ethernet ports on the routers and I have no issues its when I shut down those Ethernet ports and try using the serial interfaces when I start having issues. So my network layout is Ethernet from switch port f0/4 to port f0/0 on 2620 and serial from s0/1 on the 2620 to s0/2 on the 2621XM. My 2621XM f0/1 is whats connected to the WAN and I have no issues getting to the WAN from my 2621Xm or my 2620 but when I try pinging any website or even my WAN default gateway from my switch I get nothing!
Ive also noticed that when I do a IP NAT translation (after accessing the WAN from my 2620) on my 2621XM the source IP is of my serial connection not the ip of my 2620 router? I have my default gateway on the 2620 as the the IP of my serial interface on the 2621XM and vice versa because my LAN network is 172.16.1.0 and my WAN is 172.16.9.0. I have a /31 setup between my serial connections 172.16.11.0 (s0/1) is on the 2620 and 172.16.11.1(s0/2) is on the 2621XM. I used the SDM (ver 2.5) to setup NAT to have f0/1 with Nat outside and s0/2 as Nat inside. Encapsulation is HDLC between the serial links. Ive attached the running configs of the switch and routers.
View 2 Replies
View Related
Nov 25, 2012
I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-
kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled: AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712 <====
I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-
atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?
View 4 Replies
View Related
Oct 19, 2012
I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .
View 1 Replies
View Related
Nov 10, 2011
Need to know if i can add 1 FE card to 2650XM or 2620 Routers.i know we can add Ethernet card but it is only 10MB .
View 2 Replies
View Related
Jan 7, 2013
I'm looking for instructions on how to setup and connect two RV082 routers together with a crossover cable between their WAN ports. This is to connect two separate LANS together via an ethernet connection. For staging we are setting everything up with a crossover cable in our shop. Ultimately the crossover cable will be replaced by a microwave link between the two LANS several miles apart. There will be no internet connection.
View 7 Replies
View Related
Apr 7, 2013
I searched a lot but couldnt find a clear document about connecting 2 G.SHDSL routers back to back.First of all I am not sure which type of cable (RJ11) is used for connecting two 878 routers. Does it have to be cross or straight cable.
Which RJ11 pairs will be connected each other [code]
According the configuration samples One router must be CPE and the other must be CO for simulating DSLAM.
View 2 Replies
View Related
Jan 8, 2013
I would like configure two router (e.g. 1921) back to back via a 2 pin copper wire. Can I use HWIC-4SHDSL-E card to do it? What is the configuration I can use?
View 7 Replies
View Related
Apr 14, 2013
I have two site that has a copper wire (2 wire) connection between each router ( No Telco in between )Now I want to use 1921 router with HWIC-4SH DSL-E card to connect these two ste together.Can I use attach configuration to make the connection reference from the diagram?
View 2 Replies
View Related
Feb 29, 2012
Just to get this clear as having issues with a E1 link with CRC's at one.Router A,Network-Clock-Participate WIC 1,Should router B have clock participate for WIC 1? We currently have controllers set as UNFRAMED but guess we can set to NO-CRC4 both ends and telco will pass this.
View 1 Replies
View Related
Aug 28, 2012
securing a back-toback connection using E1.The connection is between two cities, using 2x CISCO 1841 router + VWIC-1MFT-E1 interface at each city.
The E1 connections has been provided by our local telco, and they are completely private. The customer is a bank, and they asking me if this is a secure connection or not. If possible, we need to guarantee that no body can get access to the bank network even if they brought E1 modem at one of the ends (telco PoP).
View 11 Replies
View Related
Dec 15, 2011
I'm having some trouble getting two Cisco 888's to work correctly back to back.. The two routers will ultimately be used in conjunction with a BT EPS8 circuit which is effectively four wires short distance between customer sites. We have configured lots of these using the older Cisco 878's.
Anyway, as i've been struggling to get line sync on site I've gone back to basics and connected the two 888's back to back. However, I've found that no matter what I do I can only get the routers to sync at 384kbps!? And that's with a one meter RJ11-RJ11 cable.. Very strange. When we've used the 878's we get much more bandwidth. I have tried statically assigning the line rate at both ends but it still only works at 384kbps.
View 3 Replies
View Related
May 26, 2013
I am setting up my lab using two 2901 routers which is running on 15.2 IOS.I am trying to simulate a back to back BRI.BRI Module: WIC-1B-S/T-V3 (x2) one of each router.
I followed this amazing document to understand the concept of BRI and configuration. url..but it never says if i can use the module that i have mentioned.
Q1. What cabling i need to use to setup back to back BRI using 2x 2901 routers with these modules?
Q2. What cabling do i need to use.
Q3. Is it actually possible to use these 2 modules alone to simulate a back to back BRI..?
View 6 Replies
View Related
Jul 15, 2012
What the little green/red light is on the back upper left corner of the switch is? It inside a little mesh and I belive it says vt_fail next to it.
Had water get on our switch over the weekend and this guy goes red when I fire off on demand diagnostic, but not relevant errors in any of the logs. Haven't gotten to the point where I am putting data back on the switch yet.
View 1 Replies
View Related
Jan 16, 2012
I have a cisco 800 that needs to be reset back to factory defaults. I tried typing in "config factory-default 10.10.10.1 255.255.255.0" at the conf t prompt, but I got an error Invaild input detected at ^ (the ^ is just under the word factory). So after a bit of reserch I came across this command "write erase" that seemed to do something but now I can't get any ip addreses. Here is the running config:
Using 1104 out of 131072 bytes
!
version 12.4
service config
[Code].....
View 13 Replies
View Related
Feb 12, 2012
On a 6500 switch running ios 12.2, is there a way of clearing all config settings for a specified interface? I want to avoid going through and having to type "no blah blah etc" for each line.
View 2 Replies
View Related
Mar 2, 2012
I have been having a weird connection issue for a week or so.The problem is at the first time i boot up my modem it simply cant connect.DSL Line LED keeps blinking- handshaking and training as it says in modem config page.After maybe 5 minutes or 2 hours, totally random.It picks up the connection, i can use it for hours until it randomly drops down once again.Ive contacted my ISP and they came over two times, they state the line quality is not suitable for my connection speed and it will be solved if i drop down my connection speed.Doing that is a painful process cause there is no other speed/quota package suitable for me, so i wanted to ask you people about it before i take action.
My modem is a Dynalink RTA1320 and i tried with another modem, tried mine in a friends house.Plus i went to the place where the cable enters my house and tried over there too, it didnt work as it should pick up in about 20 seconds.Here are stats my modem shows in the config page.[CODE]
View 4 Replies
View Related
Mar 4, 2013
I have a ASA 5505 configured with three VLANs: Inside, Outside, and DMZ.I am running an exchange server on the Inside network and have configured NAT to allow connections to it from outside. This works fine. I can also happily connect to it using it's internal address from the inside. In the DMZ I have setup a linksys router to work as a guest wifi network. I configured the ASA to block any traffic from the DMZ to the internal network.This has been working fine for the last few weeks.Wireless users cannot access any internal resoureces, but can browse the internet etc.. etc..
My problem is that I want users to be able to connect to the wireless with smartphones, tablets etc..., if they do so, they can access the internet, but not get their email. From my (limited) understanding, the problem is that the ip address I am trying to connect to is the same ip that I am transmitting from. Is there any way to send the packets to the outside network and then loop them back to the exchange server?
View 3 Replies
View Related
Jun 7, 2012
I have a bunch of 3750x switches that each have a 10 gig routed link back to a central 4507 (loopback = 172.30.255.255).We carved up a /24 (of course, the /24 doesn't really exist except in our address tracking spreadsheet) into a bunch of /30's for routed WAN links and /32's for loopback addresses.We started on the low end for /30 subnets (ie 172.30.255.0/30, 172.30.255.4/30, etc.).We started at the high end for the /32 loopbacks (ie 172.30.255.255/32, 172.30.255.254/32, etc.)
Well, when I try pinging 172.30.255.255 from the access layer 3750x switches, the 3750x seems to be treating it as a broadcast ping where it lists each member that responds instead of the regular !!!!! response (this makes think something is odd with the 3750x). Of course, only one member responds (the core). But even the core seems to respond with the other end of the /30 instead of the actual /32 loopback (which makes me think something is odd in the core). I could have sworn that I've setup similar topologies without problems (ie, using 10.0.0.0/32, 10.255.255.255/32, etc as loopbacks) and as long as the mask is a /32, it should work.Also, I can ping/ssh to that loopback if my laptop is on a directly connected subnet. But I can't do it from any of the 3750x switches (which are also directly connected).I've double checked for overlapping subnets, but nope. I don't see any. Routing looks fine. The actual /32 is being propagated everywhere properly.
View 3 Replies
View Related
Aug 28, 2012
I have a network that has a pair of 6500 switches on either end, running HSRP. In between each 6500 are two to three ruggedcom switches. They are connected to each other and the 6500's by trunk ports in a straight line. The 6500's see each other as CDP neighbors, and the 6500's can see the rugged- com as LLDP neighbors (ruggedcom only supports LLDP).
The issue is that randomly devices on the ruggedcoms will drop offline and then come back. The problem is that the devices that drop offline are all in the same VLAN, so it appears like a virus - i.e. one device drops off, then multiple. Eventually the HSRP starts flapping between the two 6500s and this causes havoc on the network.I'm almost to the point of taking a laptop and plugging it into one of the ruggedcom's to see traffic, but the issue is that the ruggedcoms are outside in cabinets that laptops shouldnt be exposed to.
View 2 Replies
View Related
Aug 18, 2012
The following error was seen on the switch and the Diagnostic Test Loop back failed following a new WS-6748-SFP module installation.Fabric in slot 5 detected excessive flow-control on channel 3 (Module 4, fabric connection 1)
Tried Hard reset of the module and still the error persist.
View 4 Replies
View Related
Mar 28, 2013
We recently extended our access layer using a pair of 5ks with extenders. We have a pair of 6509s at our core and they handle the intra-VLAN routing with SVIs. I recently noticed that access hosts connected to the extenders cannot pass traffic between each other if they are in different VLANs. The strange thing is these same hosts can ping devices in other VLANs as long as the other devices are not connected to the 5k environment.
For example, consider the following hosts. Each host has their gateway set to the appropriate SVI on our core.
HostA - VLAN100 - connected to 5k extender
HostB - VLAN200 - connected to 5k extender
HostC - VLAN100 - connected to 2960 off our core
HostD - VLAN200 - connected to 2960 off our core
Each host can ping each other with the exception of HostA and HostB. As for specifics, we use HSRP (no VSS) between our cores.
When I ping between hostA and hostB, I see the egress packets on either 5k1 or 5k2. I then see ingress AND egress on Core1. There are no ingress packets on 5k1 or 5k2.The egress packets from Core1 show the correct destination MAC address of the target host. The mac address table shows the mac address on po31.
View 16 Replies
View Related
Jul 17, 2012
I'm having with VSS Failover. Currently I have two 6504's setup for VSS with one connection to the sup engine (10Gig__Connection) and the other connection on the Module 3 10Gig Blade and the same setup on the other 6504.My question is: If the active 6504 has a power outage or the link on the sup engine goes down, and the standby 6504 becomes active, what happens when the Failed 6504 comes back online with a higher priority and preempt set? What happens with the 6504 that took over as Active and now eeds to go back to Standby, what's required?
What I'm seeing is once the Standby took over and became Active in order for him to go back to Standby mode it's asking for a reload to take place is this NORMAL?
View 2 Replies
View Related
Apr 6, 2012
Here is my Lab Setup: 2691 is BGP nei to R4 router and they are not directly connected. 2691 and R4 are in same AS 6500. 2691 Config---router ospf 1 network 3.3.3.3 0.0.0.0 area 0 . Its advertising its loop back IP to OSPF domain.
router bgp 6500
no synchronization
bgp log-neighbor-changes
neighbor 6.6.6.6 remote-as 6500
neighbor 6.6.6.6 update-source Loopback3
[code]...
R4 Router
router ospf 11
log-adjacency-changes
network 6.6.6.6 0.0.0.0 area 0
[ code].....
We can see that 2691 and R4 are BGP neis and 2691 has 200.1.x.x routes in its route table. My question is why from 2691 router i am unable to ping any route learned by BGP from R4?
2691Router# ping 50.1.1.0 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 50.1.1.0, timeout is 2 seconds:.....Success rate is 0 percent (0/5)2691Router#ping 200.1.2.0 [ code]...
View 12 Replies
View Related
Jun 15, 2012
We have multiple cisco cat 2900 switches. all switches don't have cascade cable port in back panel. i want some sort of solution to manage those switch remotely.
View 9 Replies
View Related
Jan 15, 2012
A customer wants to get the back-plane load of a cat4506-e chassis with a sup6-E supervisory card.A would like to check how many bus are used on the backplane and if the command "sh envi chassis" is the good and only command to be used ?I'm not sur that there is only one bus on the cat4506-E as with a sup7 card the backbone speed can change.
View 2 Replies
View Related
Sep 14, 2012
I am trying to configure a loop back interface like so: [URL], on the following device:
C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(50)SE, RELEASE SOFTWARE (fc1on port gig0/1 which is using a 1000Base-SX adapter. This is for troubleshooting purposes and it does not appear to be a feasible option. Is there another way to accomplish in the IOS?
View 1 Replies
View Related
Jun 20, 2010
I have configured 887 Router. ADSL with 3g(backup) everything is fine but the routing seems not working.interface ATM0 backup delay 120 60 backup interface Cellular0 no ip address no atm ilmi-keepalive dsl bitswap both [code] Tha nat is working but the routing seems not working. When I run remove "ip route 0.0.0.0 0.0.0.0 Dialer0" command I can connect internet. but it did not work. When I disconnect adsl line and run sh route, I see dialer 0 is the default route for 0.0.0.0. I need to configure backup route for 0.0.0.0 network
View 12 Replies
View Related
Nov 9, 2011
I have an iPad that uses an app to control the house. I create a dyndns url to maintain connection to the house from the outside world. When I bring the iPad onto the internal network, the url routing fails. Externally, it works fine. I think it's some sort of protection that is configured within the router.
Proper configuration to allow the URL to kind of loop back onto itself, when it's in the house? Where, in the configuration, this is set to prevent this kind of routing?
View 1 Replies
View Related
Jun 30, 2012
I have set up port forwarding for my WD Network HDD, which runs a Media Server (Twonky). Now, I have tested the ports and accessed it through the internet and it works fine, until... I click a link to open a folder and suddenly I get a "No such page" error thing. I have however identified this problem, it seems that when I go off the main page it re-routes to the original network address, not my IP forward address. For Example if my IP was 82.9.12.456 and the port was 800 i would go to "82.9.12.456:800" and it would load but once I navigate i go to "192.168.0.*:800/*****" and does not load the page. If i then copy and past my IP into the URL it works, but this is annoying.
View 3 Replies
View Related
Sep 19, 2012
cannot find wep supposed to be on back of router
View 1 Replies
View Related
