Cisco Switching/Routing :: 2691 / 6500 - Unable To Ping IP Of IBGP Nei Loop Back
Apr 6, 2012
Here is my Lab Setup: 2691 is BGP nei to R4 router and they are not directly connected. 2691 and R4 are in same AS 6500. 2691 Config---router ospf 1 network 3.3.3.3 0.0.0.0 area 0 . Its advertising its loop back IP to OSPF domain.
router bgp 6500
no synchronization
bgp log-neighbor-changes
neighbor 6.6.6.6 remote-as 6500
neighbor 6.6.6.6 update-source Loopback3
[code]...
R4 Router
router ospf 11
log-adjacency-changes
network 6.6.6.6 0.0.0.0 area 0
[ code].....
We can see that 2691 and R4 are BGP neis and 2691 has 200.1.x.x routes in its route table. My question is why from 2691 router i am unable to ping any route learned by BGP from R4?
2691Router# ping 50.1.1.0 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 50.1.1.0, timeout is 2 seconds:.....Success rate is 0 percent (0/5)2691Router#ping 200.1.2.0 [ code]...
View 12 Replies
ADVERTISEMENT
Jun 7, 2012
I have a bunch of 3750x switches that each have a 10 gig routed link back to a central 4507 (loopback = 172.30.255.255).We carved up a /24 (of course, the /24 doesn't really exist except in our address tracking spreadsheet) into a bunch of /30's for routed WAN links and /32's for loopback addresses.We started on the low end for /30 subnets (ie 172.30.255.0/30, 172.30.255.4/30, etc.).We started at the high end for the /32 loopbacks (ie 172.30.255.255/32, 172.30.255.254/32, etc.)
Well, when I try pinging 172.30.255.255 from the access layer 3750x switches, the 3750x seems to be treating it as a broadcast ping where it lists each member that responds instead of the regular !!!!! response (this makes think something is odd with the 3750x). Of course, only one member responds (the core). But even the core seems to respond with the other end of the /30 instead of the actual /32 loopback (which makes me think something is odd in the core). I could have sworn that I've setup similar topologies without problems (ie, using 10.0.0.0/32, 10.255.255.255/32, etc as loopbacks) and as long as the mask is a /32, it should work.Also, I can ping/ssh to that loopback if my laptop is on a directly connected subnet. But I can't do it from any of the 3750x switches (which are also directly connected).I've double checked for overlapping subnets, but nope. I don't see any. Routing looks fine. The actual /32 is being propagated everywhere properly.
View 3 Replies
View Related
Aug 18, 2012
The following error was seen on the switch and the Diagnostic Test Loop back failed following a new WS-6748-SFP module installation.Fabric in slot 5 detected excessive flow-control on channel 3 (Module 4, fabric connection 1)
Tried Hard reset of the module and still the error persist.
View 4 Replies
View Related
Sep 14, 2012
I am trying to configure a loop back interface like so: [URL], on the following device:
C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(50)SE, RELEASE SOFTWARE (fc1on port gig0/1 which is using a 1000Base-SX adapter. This is for troubleshooting purposes and it does not appear to be a feasible option. Is there another way to accomplish in the IOS?
View 1 Replies
View Related
May 10, 2012
I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
View 3 Replies
View Related
Feb 12, 2012
On a 6500 switch running ios 12.2, is there a way of clearing all config settings for a specified interface? I want to avoid going through and having to type "no blah blah etc" for each line.
View 2 Replies
View Related
Aug 28, 2012
I have a network that has a pair of 6500 switches on either end, running HSRP. In between each 6500 are two to three ruggedcom switches. They are connected to each other and the 6500's by trunk ports in a straight line. The 6500's see each other as CDP neighbors, and the 6500's can see the rugged- com as LLDP neighbors (ruggedcom only supports LLDP).
The issue is that randomly devices on the ruggedcoms will drop offline and then come back. The problem is that the devices that drop offline are all in the same VLAN, so it appears like a virus - i.e. one device drops off, then multiple. Eventually the HSRP starts flapping between the two 6500s and this causes havoc on the network.I'm almost to the point of taking a laptop and plugging it into one of the ruggedcom's to see traffic, but the issue is that the ruggedcoms are outside in cabinets that laptops shouldnt be exposed to.
View 2 Replies
View Related
Jan 18, 2013
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies
View Related
Aug 21, 2012
We have an OSPF network with four 6500 Distribution Switches. They are fully meshed and see each other as peers and are sharing routes. Off of one pair (Border) there is a setup of 3750G siwtches that go off to another network and they do not run OSPF. Between the Border Dist and the 3750G Switches we run HSRP. The 3750G side uses HSRP GP 192 and the Dist Side uses HSRP 192.There are static routes on the 3750G pointing to the Dist HSRP address to get back to network.Pings fail from the OSPF side to the HSRP address on the 3750G side.If I do a trace from the OSPF side to the HSRP address it hits one border dist switch then the other and fails.If I have static routes on both border dist switches pointing to the HSRP on the 3750side, do we need to change the metric on one dist so that it is preferred over the other or should the router Id take care of that?
View 1 Replies
View Related
Oct 24, 2012
I've spent the last two days working on this problem and it is killing me! I know the answer has to be something simple, but despite hours of searching and trying different things, I just can't seem to fix it.Essentially, I am going to be installing a Cisco 2691 and use it as the default gateway for a small business. It will be directly connected to a cable modem with a static IP. The other Ethernet interface is going to connect to a 2950 switch with a couple different VLANs.
The problem I'm having is that I can ping anything external from the router itself. From the clients connected to the 2950, I can ping IPs in other VLANs, and I can ping up to the IP of the external interface, but no pings go beyond that.I've set up NAT overload on the router, and when I do a debug ip nat, I see the pings trying to get through with the proper translations, but I still don't receive ICMP replies back.I set up GNS3 to simulate what I'm trying to accomplish (since it emulates a 2691). Attached is a jpg of the topology -- on the right is the "simulated ISP" with 3 loopback networks and one host on a different subnet. The 2691 has a static route to the "Internet" router, and can ping everything attached to the router, including the host. The host (5.5.5.5) can also ping the outside interface of the 2691 (50.50.50.2).
However, the hosts behind the 2691 can't ping past 50.50.50.2. The 192.168.0.x network can be ignored, because that network won't need to access the Internet. But the 10.10.20.x (VLAN 20) and 10.10.30.x (VLAN 30) networks will need to. In the simulation, the hosts are 10.10.20.5 and 30.5. They can ping each other, their default gateways, and the 2691 outside interface (50.50.50.2) but not the other side, the "Internet" router at 50.50.50.1 or beyond.
[code]....
View 4 Replies
View Related
Nov 25, 2012
I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-
kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled: AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712 <====
I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-
atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?
View 4 Replies
View Related
Dec 4, 2011
What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?
View 1 Replies
View Related
Apr 11, 2013
I have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?
View 1 Replies
View Related
Nov 25, 2011
I have 2650XM router and 2620 Router Both routers have built in WIC T1 CSU/DSU cards
2620Router --
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: DTE side
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
[code]....
My question is that cisco website says there are two type of cable connections for this type of config --which are --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable it did not work.So for this type of connection i know i need T1 cross over cable-- which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over -- will this cable work in my router to router connection.
View 5 Replies
View Related
Oct 19, 2012
I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .
View 1 Replies
View Related
Aug 12, 2011
What is the purpose of loop back testing.
View 2 Replies
View Related
Apr 21, 2013
I don't do a lot of networking however during a cisco lesson the other day my lecturer briefly touched upon loop-back tests, would it be okay for somebody to very imply sum up exactly what loop-back tests do in a couple of lines and how they are carried out? (not in detail, so literally for example - a wire is put in from one end of the network to the other etc.) I don't really understand all the different wiring types etc.
View 4 Replies
View Related
Sep 30, 2011
I recently replaced a client's router with a Cisco RV 120W. The client employs a web-based application on an internal server that manages their business. Workers in the field use a handheld device power by WIndows Mobile to access a mobile version of the the web-based app. Data contained on the mobile app syncronizes with the server when workers choose a sync menu. Some workers perform this sync in the field, others wait till they return to the office and use the wireless provided by the router. Prior to changing the router, the synching worked fine either inside or outside the company network. The mobile app accesses the internal server via the router's public IP address. The router forwards the http requests to the internal server. But now the synching does not work internally. I assume it's because the Cisco RV 120 W does not support NAT Loopback, or I simply haven't figured out how to enable it. Does anyone know how to enable NAT Loopback on the RV 120 W so I can access the web-based app by through the router's external IP while on the private side of the LAN??
View 2 Replies
View Related
Oct 24, 2011
I have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.
View 9 Replies
View Related
Jul 12, 2011
I am working with a device that does not have a physical reset button on it, and have mistakenly typed in 127.x.x.127 for it's IP. I was trying to use 172, but mistyped and didn't catch it until after I had rebooted the unit. Is there anyway that I might be able to gain access to the device. My PC is running Windows 7, but I am familiar with linux as well. I have attempted to change the loopback adapter IP to 128 on a ubuntu live disc and set my ethernet port to the subnet the device is on with no avail. (I am also using vlans on the device, but believe I have them set up correctly)the device is set to IP: 127.x.x.127 netmask 255.255.255.128. [code] I know that the last octet of 127 is the broadcast IP for the range, but have been able to address similar blunders before by forcing myself to a /24 subnet to correct that.
View 5 Replies
View Related
May 7, 2012
I am terminating GRE vrf-lite on my 7600 and using loopback as source for each client.I found one problem where 7600 seems to be not forwarding traffic until I delete create the tunnel interface.Worked fine for a week. Then stopped again. I had to delete,create again tunnel interface.
View 6 Replies
View Related
Jan 12, 2013
We have 6 WAN routers connected through ISP MPLS cloud , we need to implement GET VPN between these WAN routers.We have 2 Key servers (1800 routers) , and the WAN routers will act as Group Members (6 GMs)
The attached configuration files are for working configuration for typical GETVPN (crypto map applied on WAN interface)
In Key server configuration , the crypto isakmp command is using the WAN interface IP address of each WAN router (172.16.x.x) , and since that the KS routers are connected to local backbone (VSS) , they should be able to reach 172.16.X.X , and therefore the subnet 172.16.X.X is advertised to the local network (check GM configuration file under eigrp - redist connected )
This is what our customer want to avoid ! they do not want 172.16.X.X to be advertised to the local network .I know It is possible in GETVPN configuration to configure ,the crypto isakmp command to use loopback address's of the WAN routers instead of the WAN IP , but in this case the crypto map must be applied to the loopback address , and this requires all traffic to be encrypted and decrypted to go through the loopback interfaces on all WAN routers .
i was wondering what is the best solution for this case , I though to use the below config on the GM's
View 14 Replies
View Related
Dec 20, 2011
My 2691 Router has already 2 serial cards WIC-1DSU-T1 installed, When i install the 3rd serial card and reboot the router, it detects the 3rd card installed but 3rd card has no light.
When i do sh ver it shows 3 cards installed.
When i install this 3rd serial card to other Router then light shows on card and it works fine
So i am thinking if 2691 Router only supports 2 serial cards?
View 3 Replies
View Related
Nov 22, 2011
I was wondering if i can enable url filtering on my 2691 or 2651XM routers so that if someone visits any website i can see that under router logs. right now i am using kiwi syslog that logs the router activities.
View 3 Replies
View Related
Sep 5, 2012
We're starting to share video across our network and would like to setup multicast to conserve at least some of the bandwidth. We have a broad mix of equipment (A Catalyst 6509-E at the core, a combination for Cisco 2691 & 2811 routers, and a whole lot of Catalyst 3500, 3550, 3560 switches at a hundred locations. Where would I begin? Would I need to define routing for the multicast IP addresses (224.0.0.0)? Would I need to setup interfaces & IP networks where each multicast device is located like I would for a new IP subnet?
View 1 Replies
View Related
Dec 3, 2011
On my 2691 Router i see the buffer leak due to syslog
2691Router# sh buffers leak
Header DataArea Pool Size Link Enc Flags Input Output User
650743C4 F200084 Small 0 0 0 0 None None Init
[Code].....
View 17 Replies
View Related
Sep 5, 2011
I've got an SG300-10P switch and am trying to use it to create a testing environment for a Fiber Test set. What I would like to do is get two hosts, A & B, plugged into ports 1 and 3 on the switch, to talk to each other, but forcing the traffic to be routed through the two Combo ports 9 & 10. Please see the attached diagram.I've attempted to configure two VLAN's, 10 and 20. Vlan 10 is used for traffic between Ports 1 and 9, Vlan 20 is used for traffic between Ports 3 and 10.I don't really care whether the traffic is tagged or untagged as it passes between ports 9 and 10.
I've tried various combinations of tagged/untagged ports, PVID's, etc. As a first test I've bypassed the Fiber Test set and simply created a direct connection between ports 9 and 10. I am unable to get the traffic from Host A to Host B to get routed through ports 9 and 10 (I ping each host from the other and get no response).
View 7 Replies
View Related
Feb 19, 2013
I need to NAT a port range spanning from TCP and UDP 50,000 to 59,999 from inside global address 58.96.x.x on loopback2 to an inside local address of 192.168.5.5.Currently all the existing NAT translations are 1-to-1 that map inside global addresses on a wide span of Loopbacks and a Dialer Interface to inside local addresses on few subnets which are fine.I'm using an 1811 with an ADVIPSERVICESK9-M image, version 12.4(6)TS
View 1 Replies
View Related
Nov 22, 2012
I am having a hard time trying to configure DMVPN with the tunnel being sourced via a loopback interface. All routers are Cisco 886 routers which don't have L3 ports.That is why I used SVI interfaces, and have configured the L2 ports (Fa0, Fa1, etc.) with the command switchport access vlan.The problem is that I am receiving Invalid SPI error's only on the Hub router and I have no clue what could be the problem, because they use exactly the same parameters for IPsec. [code]
View 1 Replies
View Related
Feb 17, 2012
I have 2 modules of FWSM in 6500 switch (failover). I need 5 context. When I use in routed mode (like in the picture) , I cannot ping the servers behind the firewall. (I have ping to FW context) In transparent mode, it is not happening.
View 1 Replies
View Related
Mar 6, 2013
I tried to clear monitor session on 6500 and keep on getting the following error:
%Another session parameters or permit-list is being configured %Please wait for another configuration to complete.
how i can go about clearing the monitor session.
View 9 Replies
View Related
Jul 4, 2012
How to create loopback cable for gig copper port (cisco 6513).I
View 3 Replies
View Related
Nov 17, 2012
I have a couple a questions answers on which i cant google for a period. BTW maybe i simly use wrong aproach to choose keywords.
1) Is it possible to assign same ip address to the same client each time it authenticated, preferably without using DHCP? Im definely sure that it possible but cant find corresponded configuration examples (my device is Cisco 1921 with IOS 15.0.1).
2) Is it possible to assign dynamic crypto map to loopback interface (the purpose to make EASY VPN Server accessible through two interfaces - maybe you recommend other approach instead?) - as i move workingcrypto map from phy int to loopback - i cant connect with reason "Phace1 SA policy proposal not accepted"
View 3 Replies
View Related
