Cisco LAN :: 6513 How To Create Loop Back Cable For Gig Copper Port
Jul 4, 2012How to create loopback cable for gig copper port (cisco 6513).I
View 3 Replies
ADVERTISEMENT
Cisco WAN :: 1921 / Connect Two Router Back To Back Via 2 Pin Copper Wire?
Jan 8, 2013I would like configure two router (e.g. 1921) back to back via a 2 pin copper wire. Can I use HWIC-4SHDSL-E card to do it? What is the configuration I can use?
View 7 Replies View RelatedCisco Firewall :: 1811 NAT Port Range From Loop Back
Feb 19, 2013I need to NAT a port range spanning from TCP and UDP 50,000 to 59,999 from inside global address 58.96.x.x on loopback2 to an inside local address of 192.168.5.5.Currently all the existing NAT translations are 1-to-1 that map inside global addresses on a wide span of Loopbacks and a Dialer Interface to inside local addresses on few subnets which are fine.I'm using an 1811 with an ADVIPSERVICESK9-M image, version 12.4(6)TS
View 1 Replies View RelatedCisco Switching/Routing :: C3550 - Configure Loop Back Interface On Gigabit Fiber Port
Sep 14, 2012I am trying to configure a loop back interface like so: [URL], on the following device:
C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(50)SE, RELEASE SOFTWARE (fc1on port gig0/1 which is using a 1000Base-SX adapter. This is for troubleshooting purposes and it does not appear to be a feasible option. Is there another way to accomplish in the IOS?
Possible To Assign Loop Back Address To Typical Switch Port On 2950 Switch
Jan 16, 2011is it possible to assign a loopback address to a typical switch port on a 2950 switch? I want to be able to have some devices connected to a switch to test access lists and VLANs.
View 3 Replies View RelatedPurpose Of Loop Back Testing
Aug 12, 2011What is the purpose of loop back testing.
View 2 Replies View RelatedCisco :: Loop Back Tests For The Network
Apr 21, 2013I don't do a lot of networking however during a cisco lesson the other day my lecturer briefly touched upon loop-back tests, would it be okay for somebody to very imply sum up exactly what loop-back tests do in a couple of lines and how they are carried out? (not in detail, so literally for example - a wire is put in from one end of the network to the other etc.) I don't really understand all the different wiring types etc.
View 4 Replies View RelatedCisco Routers :: Need NAT Loop Back For RV 120W
Sep 30, 2011I recently replaced a client's router with a Cisco RV 120W. The client employs a web-based application on an internal server that manages their business. Workers in the field use a handheld device power by WIndows Mobile to access a mobile version of the the web-based app. Data contained on the mobile app syncronizes with the server when workers choose a sync menu. Some workers perform this sync in the field, others wait till they return to the office and use the wireless provided by the router. Prior to changing the router, the synching worked fine either inside or outside the company network. The mobile app accesses the internal server via the router's public IP address. The router forwards the http requests to the internal server. But now the synching does not work internally. I assume it's because the Cisco RV 120 W does not support NAT Loopback, or I simply haven't figured out how to enable it. Does anyone know how to enable NAT Loopback on the RV 120 W so I can access the web-based app by through the router's external IP while on the private side of the LAN??
View 2 Replies View RelatedAccess Device On Loop Back Subnet
Jul 12, 2011I am working with a device that does not have a physical reset button on it, and have mistakenly typed in 127.x.x.127 for it's IP. I was trying to use 172, but mistyped and didn't catch it until after I had rebooted the unit. Is there anyway that I might be able to gain access to the device. My PC is running Windows 7, but I am familiar with linux as well. I have attempted to change the loopback adapter IP to 128 on a ubuntu live disc and set my ethernet port to the subnet the device is on with no avail. (I am also using vlans on the device, but believe I have them set up correctly)the device is set to IP: 127.x.x.127 netmask 255.255.255.128. [code] I know that the last octet of 127 is the broadcast IP for the range, but have been able to address similar blunders before by forcing myself to a /24 subnet to correct that.
View 5 Replies View RelatedCisco VPN :: GRE Termination At 7600 Using Loop Back As Source
May 7, 2012I am terminating GRE vrf-lite on my 7600 and using loopback as source for each client.I found one problem where 7600 seems to be not forwarding traffic until I delete create the tunnel interface.Worked fine for a week. Then stopped again. I had to delete,create again tunnel interface.
View 6 Replies View RelatedCisco VPN :: 1800 GETVPN Crypto Map On Loop Back
Jan 12, 2013We have 6 WAN routers connected through ISP MPLS cloud , we need to implement GET VPN between these WAN routers.We have 2 Key servers (1800 routers) , and the WAN routers will act as Group Members (6 GMs)
The attached configuration files are for working configuration for typical GETVPN (crypto map applied on WAN interface)
In Key server configuration , the crypto isakmp command is using the WAN interface IP address of each WAN router (172.16.x.x) , and since that the KS routers are connected to local backbone (VSS) , they should be able to reach 172.16.X.X , and therefore the subnet 172.16.X.X is advertised to the local network (check GM configuration file under eigrp - redist connected )
This is what our customer want to avoid ! they do not want 172.16.X.X to be advertised to the local network .I know It is possible in GETVPN configuration to configure ,the crypto isakmp command to use loopback address's of the WAN routers instead of the WAN IP , but in this case the crypto map must be applied to the loopback address , and this requires all traffic to be encrypted and decrypted to go through the loopback interfaces on all WAN routers .
i was wondering what is the best solution for this case , I though to use the below config on the GM's
Cisco Switches :: How To Use SG-300 Combo Ports For Loop Back Testing
Sep 5, 2011I've got an SG300-10P switch and am trying to use it to create a testing environment for a Fiber Test set. What I would like to do is get two hosts, A & B, plugged into ports 1 and 3 on the switch, to talk to each other, but forcing the traffic to be routed through the two Combo ports 9 & 10. Please see the attached diagram.I've attempted to configure two VLAN's, 10 and 20. Vlan 10 is used for traffic between Ports 1 and 9, Vlan 20 is used for traffic between Ports 3 and 10.I don't really care whether the traffic is tagged or untagged as it passes between ports 9 and 10.
I've tried various combinations of tagged/untagged ports, PVID's, etc. As a first test I've bypassed the Fiber Test set and simply created a direct connection between ports 9 and 10. I am unable to get the traffic from Host A to Host B to get routed through ports 9 and 10 (I ping each host from the other and get no response).
Cisco VPN :: 886 DMVPN Tunnel Sourced Via Loop Back Error
Nov 22, 2012I am having a hard time trying to configure DMVPN with the tunnel being sourced via a loopback interface. All routers are Cisco 886 routers which don't have L3 ports.That is why I used SVI interfaces, and have configured the L2 ports (Fa0, Fa1, etc.) with the command switchport access vlan.The problem is that I am receiving Invalid SPI error's only on the Hub router and I have no clue what could be the problem, because they use exactly the same parameters for IPsec. [code]
View 1 Replies View RelatedCisco Switching/Routing :: 2900 All Switches Don't Have Cascade Cable Port In Back Panel
Jun 15, 2012We have multiple cisco cat 2900 switches. all switches don't have cascade cable port in back panel. i want some sort of solution to manage those switch remotely.
View 9 Replies View RelatedCisco VPN :: 1921 Loop Back Interface / Static IP Address For Client
Nov 17, 2012I have a couple a questions answers on which i cant google for a period. BTW maybe i simly use wrong aproach to choose keywords.
1) Is it possible to assign same ip address to the same client each time it authenticated, preferably without using DHCP? Im definely sure that it possible but cant find corresponded configuration examples (my device is Cisco 1921 with IOS 15.0.1).
2) Is it possible to assign dynamic crypto map to loopback interface (the purpose to make EASY VPN Server accessible through two interfaces - maybe you recommend other approach instead?) - as i move workingcrypto map from phy int to loopback - i cant connect with reason "Phace1 SA policy proposal not accepted"
Cisco Switching/Routing :: 3750x Switches / 32 Loop Back Responding As A Broadcast?
Jun 7, 2012I have a bunch of 3750x switches that each have a 10 gig routed link back to a central 4507 (loopback = 172.30.255.255).We carved up a /24 (of course, the /24 doesn't really exist except in our address tracking spreadsheet) into a bunch of /30's for routed WAN links and /32's for loopback addresses.We started on the low end for /30 subnets (ie 172.30.255.0/30, 172.30.255.4/30, etc.).We started at the high end for the /32 loopbacks (ie 172.30.255.255/32, 172.30.255.254/32, etc.)
Well, when I try pinging 172.30.255.255 from the access layer 3750x switches, the 3750x seems to be treating it as a broadcast ping where it lists each member that responds instead of the regular !!!!! response (this makes think something is odd with the 3750x). Of course, only one member responds (the core). But even the core seems to respond with the other end of the /30 instead of the actual /32 loopback (which makes me think something is odd in the core). I could have sworn that I've setup similar topologies without problems (ie, using 10.0.0.0/32, 10.255.255.255/32, etc as loopbacks) and as long as the mask is a /32, it should work.Also, I can ping/ssh to that loopback if my laptop is on a directly connected subnet. But I can't do it from any of the 3750x switches (which are also directly connected).I've double checked for overlapping subnets, but nope. I don't see any. Routing looks fine. The actual /32 is being propagated everywhere properly.
Cisco Switching/Routing :: WS-6748-SFP Diagnostic Test Loop Back Failed
Aug 18, 2012The following error was seen on the switch and the Diagnostic Test Loop back failed following a new WS-6748-SFP module installation.Fabric in slot 5 detected excessive flow-control on channel 3 (Module 4, fabric connection 1)
Tried Hard reset of the module and still the error persist.
D-Link DIR-655 :: Why Is Loop-back Only Working On Ports Forwarded In Virtual Server Section
Nov 4, 2011Why is loop-back only working on ports forwarded in the Virtual Server section and not Port Forwarding or even DMZ? I have seen a post about loop-back on the DIR-655 from a while ago that had said to disable SPI and change NAT Endpoint to independent, I have done this and loop-back still doesn't work.
View 1 Replies View RelatedCisco Switching/Routing :: 2691 / 6500 - Unable To Ping IP Of IBGP Nei Loop Back
Apr 6, 2012Here is my Lab Setup: 2691 is BGP nei to R4 router and they are not directly connected. 2691 and R4 are in same AS 6500. 2691 Config---router ospf 1 network 3.3.3.3 0.0.0.0 area 0 . Its advertising its loop back IP to OSPF domain.
router bgp 6500
no synchronization
bgp log-neighbor-changes
neighbor 6.6.6.6 remote-as 6500
neighbor 6.6.6.6 update-source Loopback3
[code]...
R4 Router
router ospf 11
log-adjacency-changes
network 6.6.6.6 0.0.0.0 area 0
[ code].....
We can see that 2691 and R4 are BGP neis and 2691 has 200.1.x.x routes in its route table. My question is why from 2691 router i am unable to ping any route learned by BGP from R4?
2691Router# ping 50.1.1.0 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 50.1.1.0, timeout is 2 seconds:.....Success rate is 0 percent (0/5)2691Router#ping 200.1.2.0 [ code]...
LAN Over Copper Twisted Pair Cable
Jan 14, 2013Is it possible to run a large LAN over copper twisted pair cables?This is to connect 41 PC's that monitor fire systems on a large hospital site.I am trying to use the existing cable that is wired in a loop all round the site.
View 2 Replies View RelatedCisco Switching/Routing :: 3750 - Create A Layer Loop Intentionally?
Mar 1, 2012I Like To Intentionally Create A Layer 2 Loop in My LabI have 2960 and 3750 switches and servers with multiple NIC's and also Some PC's and Hubs. Connections and Commands And Features Which Sould Be Disabled or Enabled)
View 4 Replies View RelatedTS-879 Pro - 8 Or 16 Port 10gb Switch For Copper?
Oct 30, 2011I am looking at doing some upgrades to my home office and i was looking at getting either 1 or 2 TS-879 Pro (Qnap9) and upgrading the nics to 10bg nics.. .but my problem is where can i get a suitable 8port or 16port switch for these..
I have never worked with 10gb stuff before ..so i am looking for advise on what switchs i can get..I will be mainly doing Vitrualization and data management on it.
Cisco Switches :: SFP-H10GB-CU1M SFP+ Copper Cable Module Speed Shows As Unknown
Jul 17, 2012I have connected 2 SG500x switches using an SFP-H10GB-CU1M SFP+ Copper Cable module. Since the port shows as a 10G port, I would expect the speed to show as 10G as well. However, it shows as "Unknown". This doesn't leave me with confidence that it is being recognized properly. The link is working properly, but I haven't run tests to verify if I'm getting full 10G throughput or not. Shouldn't it show 10G as the link speed?
View 12 Replies View RelatedCisco Switching/Routing :: 2811 Port Is Connected To Fiber Or Copper
Jan 14, 2013I need Know what connection is using on Cisco 2811 router.I have this interface in Cisco 2811, I need Know if this port is connected to Fiber or Copper. I think is copper with RJ45 but I see 100 base TX/FX so this make me doubt about it because TX its for copper link and FX for fiber. [code]
View 5 Replies View RelatedCisco WAN :: 2911 - Get Away With Configuring Blackbox With RJ45 To Copper Port On Router Ethernet?
Apr 27, 2011Purchased a 2911 router for a customer, and I'm sure I'm missing a module here.
Teleco installed T1 and left connection to smart jack. Router only has 2-3 copper ports.
Can I get away with configuring the blackbox with RJ45 to the copper port on the router ethernet or do I need to purchase a HWIC ?
Linksys Cable / DSL :: WAG160N Rebooting In Loop?
Jun 16, 2012Some years ago i have buyed a WAG160N i haven't never used, because once i plug it power, it start to reboot and reboot in a loop...Is there something to do with it or should i put it in the trash ? Firmware using is probably Ver.1.00.15?
View 6 Replies View RelatedCisco Switching/Routing :: 3925 With 48 Port Switch Module Infinite Loop
Jan 19, 2012I have a 3925 Router with a 48 port switch module (part number SM-D-ES3G-48-P). I have no problem accessing the 3925 Router, but when I go into the 48 port, I get an error that reads
Error Hardware not supported by firmware. Try loading a newer software instead. System Resetting...
I know that the wrong IOS is installed on the switch, but the problem is that this is an endless loop. The switch resets then comes back to the same error. How to get the switch out of this loop so that I can load the correct IOS.
Cisco Switching/Routing :: 6513-E / 6513 And WS-X6748-GE-TX Compatibility
Oct 29, 2012we have a chassis 6513-E and a module WS-X6748-GE-TX, I'd like to know if could I put this module in any slot, since the documentation from Cisco says that any slot from a chassis 6500-E Series can support this module. And then in the documentation of WS-X6748-GE-TX says that this module is not compatible in the slots 1-8 of the 6513 chassis, only from 9th to 13th slots, in those slots from the 6513-E we already have 4x WS-X6748-GE-TX, and we'd like to know if could we put the module in the rest of the slots. The 6513, and 6513-E is kind of confusing.
View 4 Replies View RelatedCisco Switching/Routing :: Lost Port Channel Between 6513
Feb 24, 2012We have 2 6513's that are linked via 2 10 gig interfaces, using an LACP channel.I received an alert this aft stating that the far 6513 was unreachable and the port channel int PO3 had gone down, the 2 10 gig interfaces had also gone down on either side. 5 mins later PO3 had resestablished itself and has been fine since. [code]
View 4 Replies View RelatedCisco Switching/Routing :: 6513 - Disable Logging On Specific Port
Jan 18, 2012Ask this question, if someone came across a 6513, one of the RJ45 ports are constantly falling.The question is how to disable logging on a specific portno logging event link-status does not work.
View 1 Replies View RelatedCisco Switching/Routing :: Telnet From 6513 On Port 2821 Fails
Jan 21, 2012I am having issues with 'telnet' on port 2821 to a range of servers connecting through vlan interface from my core switch 6513 running s72033_rp-DVIPSERVICESK9_WAN-VM) version 12.2(33)SXH7, RELEASE SOFTWARE (fc3). The telnet on port 1556 and 13724 is ok.
View 1 Replies View RelatedCisco Switching/Routing :: Configuring Span Port On 6513 Switch
Mar 2, 2012I have two servers, connected on two(Different) 6513 directly connected switches. Both these servers are in the same Vlan.
I have to monitor communication these two servers. I have a system connected on one of the 6513 switch, where network tool wireshark is installed.
How to configure span port.
switch 6513-1# show run int Gi10/43 --------------------Server 1 is connected
switch 6513-2# show run int Gi9/45 ------------------------Server 2 is connected
switch 6513-2# show run int Gi9/46 ------------------------System on which network tool wireshark is installed.
Linksys Wired Router :: RV042G / Create Service To Forward Public Port 9010 To Internal IP Address With Port 23?
Oct 12, 2012Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies View Related