I have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.
View 9 Replieswe need to relocate our core switch 6500 with sup 720 to another bldg
what is the command to gracefully shut it down I mean power off
I was told one can just switch off the power
we have the following setup for our network :
UserNetwork - ASA5550 - WAN Router 2911 - ISP Netowrk - Branch Routers 877s / 1941s
Since last week we started noticing this problem that the branch users started to complain of slow application response.. After verifying it with the ISP and middle network we noticed that if i ping from my machine (ie usernetwork) to the WAN Router interface (facing the ASA) , i get time outs.. which is strange cause this is directly connected to it via ethernet cable.
We have two 6500 core switches and one(primary) of them is running in VTP transparesnt mode and the other (secondary) one is running in VTP client mode. I would like to change the VTP mode of the second switch to transparent mode. Would it cause any issue. I guess i have to create VLANs onto the switch.
View 7 Replies View RelatedI am planning to migrate the core switch from cisco 3750 to Cisco catalysts 6513 switch. What could be the best approach to minimize the downtime or avoid disrupting the production. I have couple of thoughts, one method is to build the core and then replace the existing core, another option is to build the new switch as the second VTP server and once it recieves all the VTP information then disconnect the old server.
View 6 Replies View RelatedWe have a 3750X VTP Server and the rest of the switches are clients.
Due to cabling issues, we have a switch (Switch F) that we can't connect directly to the 3750X so we have it connected through another switch. Everything is set to VTP client with the correct domain and password but this not-directly-connected switch isn't receiving any VTP VLANs.
Anything I need to do on Switch D so that Switch F can receive the VTP updates?
In my organization we have several 2950T that conected each other. We have 4 floor with each floor have 1 sw except 4th flr have 3 sw.
Main server, apps, db ( 15 units) connected to core sw at 4th flr. Currently the problem is others devices can't connected to the server at core sw. Test ping and the network to core sw is intermittent problem. When ping 100 times only 30 reply. After 10 minutes the connection restored. Ping 100 times successful. It will not having problem again until the next day. This already happen 3 days. Any command for me to use to check if port or the switch having problem? Any log i can collect
Is there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?
i'm already has one internet connection is conecting directily to the Core Switch 6509, and the Switch is route any internet request with default route:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.170.10.10
10.170.10.10 is --> Next hop for the DSL router internal IP, and it's working fine.
We have a new internet connection with another ISP/ with another DSL router, how to connect both of them to exit from the Core Switch 6509.
is it ok if i make another default route to the Next hop to the new DSL router as:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.80.10.10
10.80.10.10 is --> Next hop for the new DSL router internal IP.
My workstation(10.0.0.250) directly connected to 6509_1 switch. 6509_1 is gateway with ip 10.0.0.5/22. Sometimes routing stop working, but after 3-5 minutes all back to normal.When issue occur i can't ssh to 6509_1, but i connect to second 6509_2 (10.0.0.6) and i can ssh to 6509_1 from it.Then form 6509_1 i try to ping my workstation Wireshark on my workstation show that packet arrive. My workstation reply on it, but switch not accept it.How it possible? As I say after sometime all go back to normal without any changes. [code]
View 2 Replies View RelatedI am running (cat4500-ENTSERVICES-M), Version 12.2(53)SG2 on the switch. I have a scenario where I have 3 end user equipments connected to a Cisco 4948 L3 switch. At the switch end port 1/46, 1/47, 1/48 are the terminating points for these 3 devices . I have added these three ports to VLAN140 (switch port access vlan140 on the gig interfaces).
The device connected to 1/46 is the one I'm testing some signalling features on. My requirement is to have intermittent packet drop on this interface so that my signalling associations would go down now and then. I'm trying to simulate a real-time network congestion/latency/packet drop in a simple manner.
I do not want to shut/no shut the 1/46 intf to cause this. Some way to achieve intermittent packet drop on this gig1/46 intf ?
I have a switch layer 6500 series connected to a firewall, the port configuration between them is layer 2, in another words I do not configure an IP address in the Cisco switch port to conected it in the firewall, but when a apply a policy on firewall it lose communication with others vlans, just the vlan that is connected between the switch and firewall works, attachment the design. I think that is necessary to configure the connection between the firewall and switch as layer 3 ( a port with IP address in the switch), but I would like to know why? The switch is configured with about 10 vlan and it is a inter vlan routing, a default route is configured in the switch where the gateway is the firewall.
View 5 Replies View RelatedIs this a good idea to connect access layer directly to core layer with fiber and omit the distribution layer?
View 2 Replies View RelatedIn my cisco 3845 router I can see output packet drop in some of the interfaces.I suspect that router is processing packet beyond its mix throughput limit. Moreover when i run show int fax/y switching command I can see packet drop by RP process.
View 11 Replies View RelatedI have a switch(6500) with 2 vlans(2 SUBNETS) and from the other side of my network i have 2 terminal servers.
I want to have a VIP in my 6500 switch which i have the 2 vlans and when the first vlan(network) try to connect to the VIP
my switch will forward to first terminal.When the second vlan try to connect to VIP the switch will forward to second terminal.
I'd like the switch to decide in wich terminal server will forwared the packet based on source network.
I am not sure how i can do this???I use VIP with SLB???I use NAT???PBR?
My network Infrastructure consists of 2 core switches(cisco 3950, 24 port) and 3 access switches (cisco 2960G, 48port). No distribution layer.Both Core switches are connected to the BVI of a VPN router.PVST is running in all switches. The STP results are all good. We have 3 VLAN's in the LAN an IP routing is enables in the core switch. The network diagram is attached.
The issue we are facing is that , we get intermittent packet drops while pinging towards the access switches, and there is always a higher latency towards these assess switches.These issues are present even with no other users using the LAN. But these issues are not present while pinging towards the GW.
I guess, it is because of this, we have issues the accessing file server in the LAN. How do we go ahead with the troubleshooting. Will upgrading the IOS resolve this.The present version details is..
WS-C2960G-48TC-L 12.2(44)SE6 C2960-LANBASEK9-M
how to convert the CORE 6500 from VSS to non-VSS?
View 2 Replies View RelatedI have an Issue.In my networks, 1 single user is facing Network Slowness issue. i needs to check to which port user is coneected in switch to CHeck whether that port has any errors.But problem is, i am providing support from remote location.And my concern LAN segment is Very big,I have only user Ip address details,when i ping the Ip address from Core switch it is pinging. but when i give show ip arp & give Ip address then its not learning and listing out the Mac address to trace down to the specific port.
View 3 Replies View RelatedDoing a bug scrub on our dual core, dual Sup 720 6500s tonight. We are going from s72033-advipservicesk9_wan-mz.122-33.SXI4a.bin to SXI9. I want to get a second set of eyes on my script since I have not done this for about 1 1/2 years. Following this doc:[URL]
Script:
Backup
sh ver
remote command switch show version
[Code].....
I have a network that has a pair of 6500 switches on either end, running HSRP. In between each 6500 are two to three ruggedcom switches. They are connected to each other and the 6500's by trunk ports in a straight line. The 6500's see each other as CDP neighbors, and the 6500's can see the rugged- com as LLDP neighbors (ruggedcom only supports LLDP).
The issue is that randomly devices on the ruggedcoms will drop offline and then come back. The problem is that the devices that drop offline are all in the same VLAN, so it appears like a virus - i.e. one device drops off, then multiple. Eventually the HSRP starts flapping between the two 6500s and this causes havoc on the network.I'm almost to the point of taking a laptop and plugging it into one of the ruggedcom's to see traffic, but the issue is that the ruggedcoms are outside in cabinets that laptops shouldnt be exposed to.
if you have two no of win 7 computer , and you run ping command at the same time at both PCs but the successfull at only one PC , second computer shows unsuccess full ping
View 2 Replies View RelatedAssume that we have 2 Cisco 6500 series which redundant via GLP, now my question is how can we connect a Juniper SRX firewall to our core switches?
View 2 Replies View RelatedI'm trying to configure a 2800 series router. .I'm consoled in and put a basic config on the router (see attached). After putting this basic config on, I plugged it into a small unmanaged switch, changed my laptop's IP and plugged it in the switch also. I can't ping the router from the laptop and vice versa. This is the second switch I've tried this with, so it must be.The first switch, I installed at location, connected a cisco cable to it and a local server, so i could remote in and finish configuration. In that scenario, I had plugged the switch into a managed switch and had the same result as I'm getting now--can't ping IP addresses (can't ping the switch's IP, not can it ping local IPs).
View 2 Replies View RelatedOn a 3750 you can do a show platform port-asic stats drop command. Is there a corresponding command for 6500 chassis?
View 7 Replies View RelatedI have a CAT 3560 connected to a ISR 2911 The 3560 has 2 subnets ( 192.168.1.0 /24 and 10.10.10.0 /24) The 2911 has interface GigabitEthernet0/1 on the 192.168.1.0 /24 and another GigabitEthernet0/0 on a WAN connection 172.16.7.246 I need to NAT both the 192.168.1.0 /24 and the 10.10.10.0 /24 to the single address 172.16.7.246 I have to use route-maps . I have IPSec VPN's and ZBF on the 2911 My problem is the NAT does not work for the 10.10.10.0 /24 network!Why?is my only option to use trunking between the 3560 and 2911 and subinterfaces on the 2911? I want to avoid sub-interfacing.
=============================================================
On the Cat 3560=====================!vlan 40name the 192.168.1.0 /24 subnet!vlan 60name the 10.10.10.0 /24 subnet!interface FastEthernet0/7description Connection to Router Gig0/1switchport access vlan 40!interface FastEthernet0/16description Connection pc host on the 10.10.10.0 /24 subnetswitchport access vlan 60!interface Vlan1no ip address!interface Vlan40ip address 192.168.1.4 255.255.255.0!interface Vlan60ip address 10.10.10.10 255.255.255.0!ip classlessip route 0.0.0.0 0.0.0.0 192.168.1.1
=========================
The host on the 10.10.10.0 /24 network has the 10.10.10.10 address as it's default gateway The host can not access the WAN thru NAT....
My Data Center has one single core switch where is connected several servers, one port is the link to the router wan and other port is the link to the FW, my boss wants to install 2 nexus in order to replace the single switch. All my network has only one address, for example 192.168.10.0/24 if I connect two nexus 7010 in VPC and Domain, each nexus is going to has 2 modules with 48 port 10/100/1000 rj45 and i wan to connect servers directly to each nexus, with this figure i'm going to have a group of servers connected in two different nexus, Do they can have the same network 192.168.10.0/24 considering that the nexus are in the same vdc and vlan and have only one gateway for both groups? If the answer is positive, which nexus would be the gate way for that address, the primary or secondary? Or i must have a different address for both group of servers, i mean for example 192.168.10.0/24 and 192.168.12.0/24?thus each nexus would be the gateway for that new address?
To have two nexus connected by VPC in a Domain mean that one computer connected to one nexus can share the same address or vlan with other computer connected to the other nexus????
we have a 6509 with ios 12.2.33SXJ
we have 2 WS-X6516-GE-TX, WS-X6516A-GBIC, and a WS-X6748-GE-TX with a WS-F6700-CFC daughtercard
our sup is a WS-SUP720-3B
we are experiencing packet loss for everything connected in the WS-X6748-GE-TX blade, right now we dont have any production device in that blade due to the packet loss we are experiencing.
this switch was running hybrid before it is now running native ios, however I can't recall if we didn't have that packet loss before. do i need to update a firmware of the card or daughtercard (if this is possible, can't say i've done it before).
A specific switch port which happens to be part of a 2 switch 3750 Switch Stack is seeing multiple CDP packets from 3 extra switch port interfaces that are not directly connected. Noteworthy is that the far end devices have the correct CDP entries and I physically confirmed at least two of those connections that lead to the switch "upstream to the culprit switch". Tricky part is that its production so room for maneuvering is limited. At some point I disabled all Ports save for the real uplink and the problem momentarily disappeared. Re-enable the interfaces problem resurfaces. Is there an explanation, technique to eliminate the culprit with minimal disruption?
View 4 Replies View RelatedI have a Cisco 7206VXR running 12.4(24)T3 IOS. It is configured with WCCPv2 using L2 mask redirection. I am using service groups and associated extended ACLs to select which subnets I want to redirect port 80 traffic from.
It is working fine for the subnet 192.168.1.0/24....
int gi0/2
ip wccp 10 redirect in
ip address 192.168.1.99 255.255.255.0
... however, there is OSPF running between the router and a Mikrotik device directly connected to this interface. The gateway addresses for all the client subnets are on the Mikrotik. Traffic from other subnets, e.g. 192.168.2.0/24, 192.168.3.0/24 come in on this interface and I want to redirect those too. But it appears that the redirection doesn't work for those subnets (I don't see any hits on the relevant ACL for any subnet except 192.168.1.0/24).
It seems like the router only wants to redirect traffic for subnets that it has an IP address in itself. Admittedly, all of the example configs i've found on cisco.com are for redirecting traffic from directly connected subnets but I can't find anything that denies thie possibility of redirecting any traffic that comes in on a given interface.
The question is, is this how WCCPv2 redirection works? i.e., the router must have an IP address in the subnet to be redirected?
We have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]...
what is location of flash file in 6500 Series switch and how can we take back of IOS image for 6500 series.
View 4 Replies View Relatedi have configure new ACE 30 module on top of 6500 core switch , the issues am facing whenver i want to access to https://ACE_IP and after i enter the user name and the password , it's forwared me to the follwoing page: is there anything should i configure to avoid this page ?
View 1 Replies View RelatedNowadays i have a project @ my work , the project consists of replacing our Cisco 6500 Core Switch with two other Core switches 6513E .
Is there is any tool to filter which port is connected to which server with its mac address and IP?