In my cisco 3845 router I can see output packet drop in some of the interfaces.I suspect that router is processing packet beyond its mix throughput limit. Moreover when i run show int fax/y switching command I can see packet drop by RP process.
View 11 RepliesWe are seeing output drops on a C3560 switchport, this port does not have QoS enabled -- application does not need special qos treatment, as long as packets are not droppd, so I suppose all traffic will share the same queue? then how should I read the output of "show platform port-asic stats drop" which indicates that it is queue 3 weight 2 drop? I am wondering what is the best way to fix this? enable mls QoS and increase queue 3 bandwidth share on this interface or just increase the output queue depth?
switch#sh mls qos interface gi0/1
GigabitEthernet0/1
QoS is disabled. When QoS is enabled, following settings will be applied
trust state: not trusted
[Code]......
I have a stack of 4 Cisco WS-C2960S-48FPS-L switches running c2960s-universalk9-mz.122-58.SE1 code. One of our network monitoring tools is indicating discards on a certain port on the switch. Upon further investigation I am seeing the Total output drops values change in a very odd manner.
The numbers seem to go from 573 to 1146 to 1719 then back down to 573 and it starts the same pattern over: [code]
The port utilization is quite low, the highest I've seen over the past 7 days is 3.5% with a polling period of every 30 seconds using Statseeker. Yet the discards are bouncing all over the place.
I've searched though the bugs for 12.2(58)SE1 and didn't see anything.
today I witnessed a cisco n5k that stopped playing fair. For a yet unkown reason several interfaces started to show output errors all begining within the same second. While i instantly thought this would be a wiring issue I began to ask myself what an output error actually means. Google usually brings up output drops, not regular output errors. So what is it and how can a 10G fiber interface even detect that there is a problem without receiving what it was sending?
View 2 Replies View RelatedMy workstation(10.0.0.250) directly connected to 6509_1 switch. 6509_1 is gateway with ip 10.0.0.5/22. Sometimes routing stop working, but after 3-5 minutes all back to normal.When issue occur i can't ssh to 6509_1, but i connect to second 6509_2 (10.0.0.6) and i can ssh to 6509_1 from it.Then form 6509_1 i try to ping my workstation Wireshark on my workstation show that packet arrive. My workstation reply on it, but switch not accept it.How it possible? As I say after sometime all go back to normal without any changes. [code]
View 2 Replies View RelatedI am running (cat4500-ENTSERVICES-M), Version 12.2(53)SG2 on the switch. I have a scenario where I have 3 end user equipments connected to a Cisco 4948 L3 switch. At the switch end port 1/46, 1/47, 1/48 are the terminating points for these 3 devices . I have added these three ports to VLAN140 (switch port access vlan140 on the gig interfaces).
The device connected to 1/46 is the one I'm testing some signalling features on. My requirement is to have intermittent packet drop on this interface so that my signalling associations would go down now and then. I'm trying to simulate a real-time network congestion/latency/packet drop in a simple manner.
I do not want to shut/no shut the 1/46 intf to cause this. Some way to achieve intermittent packet drop on this gig1/46 intf ?
I have a video feed coming into my 3570. It comes in at 5 minute input rate 18777000 bits/sec, 1695 packets/sec. However, the uplink to the router is much different, 5 minute output rate 130000 bits/sec, 28 packets/sec. I am in a lab and about ready to go into testing phase for a project when we discovered this problem, as this video feed is not veiwable on the other end.
Below is the config and capture from the switch.
BLOSSw1#sh int g1/0/6GigabitEthernet1/0/6 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is a44c.112f.3506 (bia a44c.112f.3506) MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 1/255, rxload 4/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:00, output hang never Last clearing of "show interface" counters 15:16:25 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute
[code]....
My network Infrastructure consists of 2 core switches(cisco 3950, 24 port) and 3 access switches (cisco 2960G, 48port). No distribution layer.Both Core switches are connected to the BVI of a VPN router.PVST is running in all switches. The STP results are all good. We have 3 VLAN's in the LAN an IP routing is enables in the core switch. The network diagram is attached.
The issue we are facing is that , we get intermittent packet drops while pinging towards the access switches, and there is always a higher latency towards these assess switches.These issues are present even with no other users using the LAN. But these issues are not present while pinging towards the GW.
I guess, it is because of this, we have issues the accessing file server in the LAN. How do we go ahead with the troubleshooting. Will upgrading the IOS resolve this.The present version details is..
WS-C2960G-48TC-L 12.2(44)SE6 C2960-LANBASEK9-M
We are receiving a large amount of output drops on 4 interfaces that connect to microwave wireless.This is playing up with our Management system. Saw a bug report but that was for 3750, not the IOS version but was a similar issue. [code] The output errors tend to happen at the same time. All ports are trunks however there are other trunks on the switch that are not having these issues. [code]
View 7 Replies View RelatedI have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.
View 9 Replies View RelatedWe have a 100Mbps metro-ethernet link connecting to a remote site. This link is terminating in our 3750-x stack switch.We are getting a LOT of output drop on that interface and our remote IP Phone calls keep going off because of that.I've disabled all kind of QoS, but no luck.
View 16 Replies View RelatedIXIA----DUT-----IXIA
| | |
|_______ |________|
DUT has redudant connections to IXIA. Im pumping traffic from IXIA and traffic takes PATH A .. When I shut PATH A, i expect traffic to shift to PATH B within 100ms (example). How do I test this ?
I having a basic query in troubleshooting E1 link , here im facing packet drop in the link and we are testing by providing local loop and remote loop from the CSU/DSU at local point and at remote point . I have tried ping test while the loop is given at local point and remote point ie i have pinged my local serial interface IP address (eg 10.0.0.1 -local & 10.0.0.2 -remote ) in Remote Loop i could see no errors and drops and also the traffic on the interface output and input is the same(eg input rate 1000bps and output rate 1000bps) .My query is that when i am pinging the local interface IP does the icmp packet travels till the loop point and comes to the same interface(like a boomerang) .
ICMP packet
->->->->->->->->->->->->->->->
R1 Local CSU/DSU | Remote CSU/DSU (remote loop given )
O-----------O------------------------------O |--------------------------------------O R2
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-|
I have a 1841 router connected to an ISP (currently SDSL EFM 10Mbps through an ISP modem, the router and the model are connected with a FastEthernet interface). On another location I have a linux server.There is an ipsec tunnel (3des-sha esp) between the router and the linux server (actually done with a crypto mac).The router has a hierarchical QOS policy on the egress interface.When sending traffic from the network inside the router to the linux host without the ipsec tunnel, everything is working fine and throughput is correct.When sending traffic from the inside network to the linux host internal ip through the ipsec tunnel, some packets are lost and the traffic throughput decrease.When sending traffic through the tunnel in the reverse direction (from the linux host to the internal network), everything is fine.I looked at the QOS statistics and the dropped packets counters don't increase. I looked at the egress/ingress interface statistics and no packets dropped there.I lowered the MTU on the egress interface, but it didn't solve the problem. I played by sending various ping icmp packets size, but even small packets are sometimes lost.I tried to check the router CPU, but it seems relatively fine (<= 10%)I captured the traffic on both side, and I see the packets emitted, and then I can see that some of the esp packets of the corresponding side are not received, so it looks like the cisco router is the culprit. This 1841 router is running: 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(24)T4,How can I troubleshoot where and why those packets are lost?
View 0 Replies View RelatedI am running ping between two Nexus 7018 over WAN link ,and I can see some set pattern of packet drop(7.40 % drop) with MTU size 1500.When I ping between my 6500 VSS pair and same Nexus 7018 over different SP WAN link on diffrent location , I am still getting same kind of packet drop (8% drop) with MTU 1500. Has any one else come across this issue with Nexus?
View 1 Replies View Relatedhere's my setup :
office 1 :
rv042 hw3
ISP:Obtain an IP automatically
office 2 :
rv042 hw3
ISP:PPPoE
VPN tunnel between both rv042, everything's fine but when i try to ssh from office 2 to an office 1's server, my connection drops.
When it drops, i can still ping pc in office 1, this is really strange!if i change the office 2 ISP to another provider (obtain an IP automatically) everything's ok !
i try to use another PPPoE ISP for office 2 and it's doing the same thing!I've also tried other rv042 in both locations with the same setup and it's doing the same thing, so it's not a router issue.
i've tried older firmware and it's doing the same thing, so it's not a firmware issue!
I have an 887VA-w connected at home. I am using ip virtual-reassembly an all interfaces (dialer and all internal VLANs), I am also using CBAC (currently setting up ZBF). The issue I am having is that I keep getting drop packet error messages and the reasons can differ. Below are some of the outputs I recieve: [code] I have done a show ip virtual-reassembly on all the interfaces and the counter is shown as 0.
View 6 Replies View RelatedWe are facing output queue problems on our ATM interfaces. A lot of output queue errors are been shown as below.
Cisco 2811 -> ATM Link -> <-ATM Link <- Cisco 3945 Routers.
Cisco 2811 Version is 124-15.T9.bin
Cisco 3945 Version is SPA.150-1.M1.bin
Cisco 2811 Output Errors
MIB OID and the values.also i want to know the values og output packet and output packet drops MIB OID values of POS interface on GSR router (12000).because i am getting many output packet drops on these pos interface.how do i get these values from the router.
View 1 Replies View RelatedI have been trolling around looking for answers on this particular subject and i have come up empty handed, how to verify if the private ip address will be suppressed in the sctp initialization packet when NAT is applied.
View 1 Replies View RelatedI am trying to troubleshoot a problem where in one of my remote site is not able to access some networks at HQ over Site to SIte VPN ( asa 5505 at Remote and 5520 at HQ). I ran packet tracer and HQ ASA looks clean as everything came out as ALLOW. Remote site ASA packet tracer give me DROP out at Phase 9 (VPN). I am not very sure what to look in ASA for resolution now. Is it an access list that is blocking the traffice or VPN setup.
View 5 Replies View Relatedwhen using egress netflow (v9) and output marking.
The topologie : Server <-----> R1 1>-----<1 R2 2>----<2 R3
R2 is a 7200 with c7200p-adventerprisek9-mz.124-15.T11.bin What I'm doing :- R2 forwards ping packets from Server to R3. When they arrive on R2, icmp packets are marked with CS3
- I change the DSCP to CS4 on R2 before forwarding packet to R3. I'm using for that an output service-policy on the R2-2 interface like this : interface ATM2/0.36 point-to-point
ip address 192.168.1.1 255.255.255.252
ip flow ingress
ip flow egress
[Code]....
I have 2 routers ( Cisco 3845's) both running identical IOS's. Each router has identical 5 networks on it with one network each being different.I have HSRP set up on the identical 5 networks.Your standard Fail over senario.ON one of the routers one network is not seeing the other router in the same network, Will not Ping or traceroute.And HSRP stopped working ( both were thinking they were active. which of course brought the network to a halt. Non of the interfaces has any ACL on them, They are plugged into a Brand new Cisco 3560v2 switch. I have switches out the cables to eliminate that as an issues.
View 1 Replies View RelatedSo in our DMVPN network, we have this Cisco 3845 hub router that is connected via a DS3 to the Internet, and our spoke sites usually have a broadband connection that typically have a maximum of 1Mbps upload capacity. We are getting ready to add a few more sites to our network that are connected to the Internet with 10Mbps upload speeds (and 50Mbps download). Spoke site routers are usually 800 series ISRs. We have seen spikes of 8-10Mbps on the hub router so far. So the question is that a site with 10Mbps upload speed transmit to the full capacity over a DMVPN tunnel or is it limited by other factors? What are those factors?
View 4 Replies View RelatedWhen you use the command switchport trunk allowed vlan add [vlan-id]There should be no drop in service to the existing VLANs, correct? I am trunking from a 7K to a 2960S via 2G PoCh.
View 2 Replies View RelatedWe are currently experiencing random multicast data dropouts on ports that are connected to a 3750X in VLAN ports. A test PC was connected to a routed port and we do not have any dropouts of the multicast data.We also took a 2960G and plugged it into VLAN ports on the 3750X. Any test PC that is on the 2960G does not lose traffic. The traffic only drops on PCs that are connected to a port on the 3750X that is in a VLAN. The data drops are random and last approximatly 55-59 seconds before we start receiving multicast traffic again.
I do not see any input/output errors on the interfacessh platform port-asic stat drop also show no drops
CPU runs at about 50% on the 3750X
Below is the configuration of the 3750X
Building configuration...
Current configuration : 8454!!version 12.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-
[Code]......
I have a 3560-24ps, and I'm having issues with it booting. When I power the device up all the front panel lights come on like normail, and then the system light starts flashing like normal, but after 5 - 6 seconds the system light goes off. I don't get any output from the console, and the fans still run.
View 5 Replies View RelatedI started having connectivity issues between my core 4506E (Sup7E) and Cisco 2960S. There were input and CRC errors on Te int (SFP 10Gb - LRM) on 2960S, which cause the interface to reset and drop connections. While troubleshooting this issue, I have replaced patch cords and also had the tech checking the fiber. He said that there was some residue on one of the connectors, so the light levels fluctuated in 1300nm, but worked fine in 850. Well LRMs are using 1300, so he re-polished the tips, which worked to stabilize the light levels. After all that, I was still receiving the input/CRC errors, but the connection was NOT dropping. As my last resort I swapped the SFPs between the core and 2960, thinking I should start having issues on the core end. Well, here's what happened: I stopped receiving input/CRC errors on 2960 (also no errors on the core), but 2960s started generating Rx power high alarms: [code]
View 1 Replies View RelatedI have users connected to a 2960-S running 12.2(53r)SE complaining of slow network, specifically Internet performance while the upstream 2960 on the same vlan has no such issues, so I don't suspect link congestion on the face of things.I'm planning on upgrading the code, but wanted to see what could be checked first. I'm seeing some drops but could use some tips on how to proceed from here as to what might be the issue. CPU is under 10% whenever I check it.
View 7 Replies View RelatedI put a QoS in a WS-C3560CG-8TC-S version 12.2(55)EX2. in our lab file upload or download speed much reduced and drop the packets with QoS everyting is fine without QoS
Here is the config: My question is why I speed reduced a lot and packets to be dropped with QoS.everything is fine WITHOUT QoS.
class-map match-any VoIP description Voice IP Phone RTPmatch access-group 157
class-map match-any WEB description Internal Web, SSL Web, DNS query, Pinnaclematch access-group 153
!
policy-map QOSMARK
class VoIP set dscp ef
class WEB set dscp cs3
[code]....
I have quite a few 2960's in a manufacturing environment that are experiencing a large number of Total Output Drops. The gigabit uplinks arn't even close to fully subscribed and if I'm lucky they run at a peak of 4 - 5 Mb on a 1Gb uplink. Something really funky is going on. The individual switchports seem to have the total output drops and the uplinks at 1Gb do not have any output drops and never peak above 20Mb over a 3 month span on a 1Gb link.
View 25 Replies View RelatedWe are seeing some high output drops on our 3560G's and I'm wondering if there is anything I can do to solve this, or should I just be looking at an upgrade.I do not have qos enabled:
do-rs-ah-3560g#show mls qos
QoS is disabled
QoS ip packet dscp rewrite is enabled
I don't have anything special configured apart from some trunk ports, otherwise its mostly defaults.Should I enable qos and tweak the buffering?
We have Cisco Catalyst 6509-V-E VSS Switch with Sup2T und IOS Version 15.0(1)SY2. We are gettin input netflow information from the gi2/3/7 but not output ... I am not sure why it does not work.
View 1 Replies View Related