Cisco Switching/Routing :: 6509 Randomly Drop Packet
Nov 1, 2012
My workstation(10.0.0.250) directly connected to 6509_1 switch. 6509_1 is gateway with ip 10.0.0.5/22. Sometimes routing stop working, but after 3-5 minutes all back to normal.When issue occur i can't ssh to 6509_1, but i connect to second 6509_2 (10.0.0.6) and i can ssh to 6509_1 from it.Then form 6509_1 i try to ping my workstation Wireshark on my workstation show that packet arrive. My workstation reply on it, but switch not accept it.How it possible? As I say after sometime all go back to normal without any changes. [code]
View 2 Replies
ADVERTISEMENT
Feb 25, 2013
I am running (cat4500-ENTSERVICES-M), Version 12.2(53)SG2 on the switch. I have a scenario where I have 3 end user equipments connected to a Cisco 4948 L3 switch. At the switch end port 1/46, 1/47, 1/48 are the terminating points for these 3 devices . I have added these three ports to VLAN140 (switch port access vlan140 on the gig interfaces).
The device connected to 1/46 is the one I'm testing some signalling features on. My requirement is to have intermittent packet drop on this interface so that my signalling associations would go down now and then. I'm trying to simulate a real-time network congestion/latency/packet drop in a simple manner.
I do not want to shut/no shut the 1/46 intf to cause this. Some way to achieve intermittent packet drop on this gig1/46 intf ?
View 3 Replies
View Related
Nov 27, 2011
In my cisco 3845 router I can see output packet drop in some of the interfaces.I suspect that router is processing packet beyond its mix throughput limit. Moreover when i run show int fax/y switching command I can see packet drop by RP process.
View 11 Replies
View Related
Aug 28, 2012
I have a network that has a pair of 6500 switches on either end, running HSRP. In between each 6500 are two to three ruggedcom switches. They are connected to each other and the 6500's by trunk ports in a straight line. The 6500's see each other as CDP neighbors, and the 6500's can see the rugged- com as LLDP neighbors (ruggedcom only supports LLDP).
The issue is that randomly devices on the ruggedcoms will drop offline and then come back. The problem is that the devices that drop offline are all in the same VLAN, so it appears like a virus - i.e. one device drops off, then multiple. Eventually the HSRP starts flapping between the two 6500s and this causes havoc on the network.I'm almost to the point of taking a laptop and plugging it into one of the ruggedcom's to see traffic, but the issue is that the ruggedcoms are outside in cabinets that laptops shouldnt be exposed to.
View 2 Replies
View Related
Oct 19, 2011
I have a stack of 4 Cisco WS-C2960S-48FPS-L switches running c2960s-universalk9-mz.122-58.SE1 code. One of our network monitoring tools is indicating discards on a certain port on the switch. Upon further investigation I am seeing the Total output drops values change in a very odd manner.
The numbers seem to go from 573 to 1146 to 1719 then back down to 573 and it starts the same pattern over: [code]
The port utilization is quite low, the highest I've seen over the past 7 days is 3.5% with a polling period of every 30 seconds using Statseeker. Yet the discards are bouncing all over the place.
I've searched though the bugs for 12.2(58)SE1 and didn't see anything.
View 13 Replies
View Related
Jan 27, 2013
My network Infrastructure consists of 2 core switches(cisco 3950, 24 port) and 3 access switches (cisco 2960G, 48port). No distribution layer.Both Core switches are connected to the BVI of a VPN router.PVST is running in all switches. The STP results are all good. We have 3 VLAN's in the LAN an IP routing is enables in the core switch. The network diagram is attached.
The issue we are facing is that , we get intermittent packet drops while pinging towards the access switches, and there is always a higher latency towards these assess switches.These issues are present even with no other users using the LAN. But these issues are not present while pinging towards the GW.
I guess, it is because of this, we have issues the accessing file server in the LAN. How do we go ahead with the troubleshooting. Will upgrading the IOS resolve this.The present version details is..
WS-C2960G-48TC-L 12.2(44)SE6 C2960-LANBASEK9-M
View 2 Replies
View Related
Oct 24, 2011
I have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.
View 9 Replies
View Related
Nov 5, 2012
I have having two Cisco 6509 both working are my main Core Switches with which I have all my Layer 2 VLANs configured and then distributed thru the trunks links to all the Access Switches. I have L3- Vlans also configured on them with which one switch in primary and the other is secondary. All of sudden last night I got this message on my core switch 2 this for VLAN 1 which is my users LAN, how can I check as to what would have caused the core switch 2 HSRP to be active and then in standby
*Nov 5 23:33:29.296: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Standby -> Active
*Nov 5 23:33:29.796: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Standby -> Active
*Nov 5 23:33:29.804: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Active -> Speak
*Nov 5 23:33:29.920: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Active -> Speak
*Nov 5 23:33:40.144: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Speak -> Standby
*Nov 5 23:33:41.280: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Speak -> Standby
Also last night i got call from office saying that we are getting huge delay in pinging the default gateway of the user LAN which is the same vlan as the above and it was just for few minutes and then it was back to normal and now when I came to office and check there were no logs in both the core switches. When I checked the cpu utlization it was showing me high on both the switches how can I check as to what would have caused the CPU utilisation to go high all of suddedn?
INPMHCORS01#$ sh processes cpu his
11111 11111 11111 1111111111
8885555588888666669999922222666665555511111777773333300000
100
90
80
[code]....
View 1 Replies
View Related
Mar 9, 2013
I can see drops on the 6509 Queue for interface gi1/6 , qos is disabled globaly with qos disabled all packets are in one Queue using best effort my question is if I can see drops using the sh queueing int Gi1/6 command why I am not seeing any drops when I run the Sh int (interface number ) command. [code]
View 7 Replies
View Related
Nov 9, 2011
i have issues logging into one of our core switches.its a 6509 switch but i cannot log in remotely.when i try to console in on the console port, i cannot log in instead i get the above error message.I haven't rebooted yet but would it solve the problem as this switch is a production switch.
View 6 Replies
View Related
Aug 16, 2012
I have been searching the message boards and wasn't having much luck. I am running some monitoring sessions on my 6509 and on the VLAN I am monitoring, I am experiencing a really large packet loss. If we hook up a laptop to the destination port and run wireshark we are seeing between 80% and 90% packet loss. I dont see the packet loss on the show port command, but I do on the show int vlan command.
The config is as follows:
Session 2
---------
Type : Local Session
Source VLANs :
RX Only : 500
[Code].....
I was doing some reading on Egress vs Ingress and I am wondering if the Egress SPAN replication state could be causing the packet loss that we are seeing or does the ingress & learn command override that?
View 0 Replies
View Related
Feb 4, 2013
IXIA----DUT-----IXIA
| | |
|_______ |________|
DUT has redudant connections to IXIA. Im pumping traffic from IXIA and traffic takes PATH A .. When I shut PATH A, i expect traffic to shift to PATH B within 100ms (example). How do I test this ?
View 2 Replies
View Related
May 22, 2012
I having a basic query in troubleshooting E1 link , here im facing packet drop in the link and we are testing by providing local loop and remote loop from the CSU/DSU at local point and at remote point . I have tried ping test while the loop is given at local point and remote point ie i have pinged my local serial interface IP address (eg 10.0.0.1 -local & 10.0.0.2 -remote ) in Remote Loop i could see no errors and drops and also the traffic on the interface output and input is the same(eg input rate 1000bps and output rate 1000bps) .My query is that when i am pinging the local interface IP does the icmp packet travels till the loop point and comes to the same interface(like a boomerang) .
ICMP packet
->->->->->->->->->->->->->->->
R1 Local CSU/DSU | Remote CSU/DSU (remote loop given )
O-----------O------------------------------O |--------------------------------------O R2
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-|
View 5 Replies
View Related
Oct 23, 2012
I have a 1841 router connected to an ISP (currently SDSL EFM 10Mbps through an ISP modem, the router and the model are connected with a FastEthernet interface). On another location I have a linux server.There is an ipsec tunnel (3des-sha esp) between the router and the linux server (actually done with a crypto mac).The router has a hierarchical QOS policy on the egress interface.When sending traffic from the network inside the router to the linux host without the ipsec tunnel, everything is working fine and throughput is correct.When sending traffic from the inside network to the linux host internal ip through the ipsec tunnel, some packets are lost and the traffic throughput decrease.When sending traffic through the tunnel in the reverse direction (from the linux host to the internal network), everything is fine.I looked at the QOS statistics and the dropped packets counters don't increase. I looked at the egress/ingress interface statistics and no packets dropped there.I lowered the MTU on the egress interface, but it didn't solve the problem. I played by sending various ping icmp packets size, but even small packets are sometimes lost.I tried to check the router CPU, but it seems relatively fine (<= 10%)I captured the traffic on both side, and I see the packets emitted, and then I can see that some of the esp packets of the corresponding side are not received, so it looks like the cisco router is the culprit. This 1841 router is running: 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(24)T4,How can I troubleshoot where and why those packets are lost?
View 0 Replies
View Related
Mar 9, 2011
I am running ping between two Nexus 7018 over WAN link ,and I can see some set pattern of packet drop(7.40 % drop) with MTU size 1500.When I ping between my 6500 VSS pair and same Nexus 7018 over different SP WAN link on diffrent location , I am still getting same kind of packet drop (8% drop) with MTU 1500. Has any one else come across this issue with Nexus?
View 1 Replies
View Related
Dec 14, 2011
here's my setup :
office 1 :
rv042 hw3
ISP:Obtain an IP automatically
office 2 :
rv042 hw3
ISP:PPPoE
VPN tunnel between both rv042, everything's fine but when i try to ssh from office 2 to an office 1's server, my connection drops.
When it drops, i can still ping pc in office 1, this is really strange!if i change the office 2 ISP to another provider (obtain an IP automatically) everything's ok !
i try to use another PPPoE ISP for office 2 and it's doing the same thing!I've also tried other rv042 in both locations with the same setup and it's doing the same thing, so it's not a router issue.
i've tried older firmware and it's doing the same thing, so it's not a firmware issue!
View 3 Replies
View Related
Mar 15, 2011
Up until recently (4 months ago) my network was fine. However, all of a sudden the network began to drop randomly. Now, the network drops about every 30 mins. Its quite an inconvenience, especially as there are two laptops, a desktop and 2 games consoles running off of the network (not all at once though). I have a Belkin Wireless G Plus MIMO router.
View 5 Replies
View Related
Sep 20, 2011
Wireless clients drop off Netgear router - Running a Netgear router in home. Have one desktop PC, 2 printers, 1 Mac and 3 Windows laptop connected. The devices that connect wirelessly will drop of the router in a random way. One printer, an HP all in one, will no longer function and I have to pull the plug to de-energize and restart it. My wireless network is a mess. I have called Netgear and for the first two months they had me change channels and adjust other settings which seemed to work at first but then these symptoms all came back.
View 1 Replies
View Related
Jul 13, 2012
I have an 887VA-w connected at home. I am using ip virtual-reassembly an all interfaces (dialer and all internal VLANs), I am also using CBAC (currently setting up ZBF). The issue I am having is that I keep getting drop packet error messages and the reasons can differ. Below are some of the outputs I recieve: [code] I have done a show ip virtual-reassembly on all the interfaces and the counter is shown as 0.
View 6 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Aug 8, 2012
When you use the command switchport trunk allowed vlan add [vlan-id]There should be no drop in service to the existing VLANs, correct? I am trunking from a 7K to a 2960S via 2G PoCh.
View 2 Replies
View Related
Apr 23, 2012
We are currently experiencing random multicast data dropouts on ports that are connected to a 3750X in VLAN ports. A test PC was connected to a routed port and we do not have any dropouts of the multicast data.We also took a 2960G and plugged it into VLAN ports on the 3750X. Any test PC that is on the 2960G does not lose traffic. The traffic only drops on PCs that are connected to a port on the 3750X that is in a VLAN. The data drops are random and last approximatly 55-59 seconds before we start receiving multicast traffic again.
I do not see any input/output errors on the interfacessh platform port-asic stat drop also show no drops
CPU runs at about 50% on the 3750X
Below is the configuration of the 3750X
Building configuration...
Current configuration : 8454!!version 12.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-
[Code]......
View 2 Replies
View Related
Nov 24, 2012
We are seeing output drops on a C3560 switchport, this port does not have QoS enabled -- application does not need special qos treatment, as long as packets are not droppd, so I suppose all traffic will share the same queue? then how should I read the output of "show platform port-asic stats drop" which indicates that it is queue 3 weight 2 drop? I am wondering what is the best way to fix this? enable mls QoS and increase queue 3 bandwidth share on this interface or just increase the output queue depth?
switch#sh mls qos interface gi0/1
GigabitEthernet0/1
QoS is disabled. When QoS is enabled, following settings will be applied
trust state: not trusted
[Code]......
View 8 Replies
View Related
Dec 29, 2011
I started having connectivity issues between my core 4506E (Sup7E) and Cisco 2960S. There were input and CRC errors on Te int (SFP 10Gb - LRM) on 2960S, which cause the interface to reset and drop connections. While troubleshooting this issue, I have replaced patch cords and also had the tech checking the fiber. He said that there was some residue on one of the connectors, so the light levels fluctuated in 1300nm, but worked fine in 850. Well LRMs are using 1300, so he re-polished the tips, which worked to stabilize the light levels. After all that, I was still receiving the input/CRC errors, but the connection was NOT dropping. As my last resort I swapped the SFPs between the core and 2960, thinking I should start having issues on the core end. Well, here's what happened: I stopped receiving input/CRC errors on 2960 (also no errors on the core), but 2960s started generating Rx power high alarms: [code]
View 1 Replies
View Related
Jul 25, 2012
I have users connected to a 2960-S running 12.2(53r)SE complaining of slow network, specifically Internet performance while the upstream 2960 on the same vlan has no such issues, so I don't suspect link congestion on the face of things.I'm planning on upgrading the code, but wanted to see what could be checked first. I'm seeing some drops but could use some tips on how to proceed from here as to what might be the issue. CPU is under 10% whenever I check it.
View 7 Replies
View Related
Apr 11, 2012
I put a QoS in a WS-C3560CG-8TC-S version 12.2(55)EX2. in our lab file upload or download speed much reduced and drop the packets with QoS everyting is fine without QoS
Here is the config: My question is why I speed reduced a lot and packets to be dropped with QoS.everything is fine WITHOUT QoS.
class-map match-any VoIP description Voice IP Phone RTPmatch access-group 157
class-map match-any WEB description Internal Web, SSL Web, DNS query, Pinnaclematch access-group 153
!
policy-map QOSMARK
class VoIP set dscp ef
class WEB set dscp cs3
[code]....
View 4 Replies
View Related
Mar 31, 2012
I've got a 1760 router which uses port forwarding (25, 80 and 443) for my internal network services. If, let's say, I try to open a FTP connection on the router, of course the connection will be refused. Is there a way to make the router DROP the packets instead of rejecting them? My Linux iptables configurations drop packets who fail the firewall test, so I would like the router to perform that behavior.Commands for port forwarding:ip nat inside source static tcp 10.10.0.1 80 int f0/0 80 (these work fine)
View 4 Replies
View Related
Feb 21, 2012
On a 3750 you can do a show platform port-asic stats drop command. Is there a corresponding command for 6500 chassis?
View 7 Replies
View Related
Nov 24, 2012
I have a switch which is rebooting it self, we bought it a year back,its a new switch, i did not find any error on sh ver after rebooting. I am using OP manager, i did not receive any alerts. I have done all diagnostic test, all are passed, i did not find any problem..
View 2 Replies
View Related
Jun 4, 2008
device: MSFC2(C6MSFC2-BOOT-M), Version 2.1(8a)EX.
A_Root(config)#interface Vlan 15
A_Root(config-if)#ip route-cache flow
Q: When I do 'show ip cache flow', only 1 packet per IP is printed(see attached file).
View 9 Replies
View Related
Dec 20, 2011
What the message below means? It's from our WS-C4506-E log running Version 03.01.01.SG.
Dec 20 16:27:26.182: (Suppressed 851 times)Dup Packet Fail for Sw PortDec 20 2011 16:27:28.068 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet4/22, changed state to upDec 20 2011 16:27:29.070 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4/22, changed state to upDec 20 2011 16:29:13.738 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4/22, changed state to downDec 20 2011 16:29:14.738 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet4/22, changed state to downDec 20 16:42:37.173: (Suppressed 162 times)Dup Packet Fail for Sw PortDec 20 2011 16:42:39.071 UTC: %LINK-3-[Code]....
View 2 Replies
View Related
Apr 1, 2013
I operate between c6509-E, what did you flooding? its just packet capture gi1/3 but i dont know it and is it attack?also same seq no switch gots it?what is problem?
View 2 Replies
View Related
