Cisco Switching/Routing :: 6500 - Show Platform Port-asic Stats Drop Command?
Feb 21, 2012On a 3750 you can do a show platform port-asic stats drop command. Is there a corresponding command for 6500 chassis?
View 7 Replies
ADVERTISEMENT
Cisco Switching/Routing :: WS-CBS3120X-S - Sh Platform Port Asic Stats Drops
Dec 10, 2012In our environment we have some HP chassis, and with them there are blade switches. Lately, we've been seeing some drops on few servers connected on the blade switch ports. The switch model is WS-CBS3120X-S. And below is the tx drop for two interfaces ( where the servers are connected to).
sh platform port-asic stats drop gi1/0/11
Interface Gi1/0/11 TxQueue Drop Statistics
Queue 0
Weight 0 Frames 0
Weight 1 Frames 0
[Code]...
Cisco Switching/Routing :: 6500 - Show Platform Capture ELAM Asic
May 29, 2012I know that an ELAM can be setup on a 6500 running ipservices 12.2(33)SXJ, however I noticed that following commands are not available on a 6500 router running advipservices 12.2(33)SXJ:show platform capture elam asic etc
So I wanted to know if there is an alternate way to setup an ELAM for troubleshooting purposes?
Cisco Switching/Routing :: 3560G 15.0(2)SE - Show Platform Forward Command Crashes Switch?
Dec 5, 2012I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
View 3 Replies View RelatedCisco Switching/Routing :: Cat 6500 Sup 2t TCAM Counter Show Command?
Sep 26, 2012Any command similar to sup720 "show tcam counters" It doesn't work on Sup2t.....
View 2 Replies View RelatedCisco :: 1142 How To Interpret Show AP Stats Command
Aug 9, 2010Is there a good reference in how to interpret the "show AP stats" command?
I have a new (online for 15 days) 1142 listed below. It is the first 802.11n AP I've deployed. The stat counters look bad [code] But I don't know how to put it all together to say "here are the stats, this is the problem". I see TxFrameCount, but no corresponding RxFrameCount, so it is hard to calibrate some of the errors. [code]
Cisco WAN :: Police Flow Command Works Only In 6500 Platform
Nov 13, 2011How the police flow command ( see below) works only in the 6500's platform? Can it apply in 3745 router?
View 2 Replies View RelatedCisco Switching/Routing :: 3750G Port Grouping Per Asic
Jun 12, 2012I have a 48-port 3750G switch (model # WS-C3750G-48TS-S). How do I determine which ports are grouped per ASIC on the 3750G switch? For example, is the grouping ports 1-8 is serviced by ASIC 1, ports 9-16 is serviced by ASIC 2, ports 17-24 is serviced by ASIC 3, etc. If it exists, what is the IOS command to show the mapping of ports to ASIC?
View 2 Replies View RelatedCisco Switching/Routing :: Doubt About WS-X6148A-GE-TX Port-ASIC Mapping
Jan 4, 2012Can some clarify what is the Port-Asic mapping in WS-X6148A-GE-TX.
View 3 Replies View RelatedCisco Switching/Routing :: Correct Number Of Port Asic In WS-X6704-LC
Jan 1, 2012Clarifying whats the correct # of port asic in WS-X6704-LC?According to the following link (Catalyst 6500 Architectural white paper): [URL]
"In the WS-X6704-10GE line card, there are two port ASICs each supporting 2 x 10 Gigabit Ethernet ports"
While in the document: Understanding Quality of Service on the Catalyst 6500 Switch: [URL]
Table 10.
WS-X6704
Number of 10 GE Ports 4
- QoS on 10-Gigabit Ethernet Line Cards (WS-X6704-10GE)
So whats correct? 4 port asic or 2 port asic?
# Port ASIC’s on the linecard 4
# Physical Ports per Port ASIC 1
Cisco Switching/Routing :: How Port-ASIC Mapping In Linecard WS-X6148-GE-TX
Dec 28, 2011how is port-ASIC mapping in linecard WS-X6148-GE-TX?
View 5 Replies View RelatedCisco Switching/Routing :: 6500 - Randomly Devices Will Drop Offline And Then Come Back
Aug 28, 2012I have a network that has a pair of 6500 switches on either end, running HSRP. In between each 6500 are two to three ruggedcom switches. They are connected to each other and the 6500's by trunk ports in a straight line. The 6500's see each other as CDP neighbors, and the 6500's can see the rugged- com as LLDP neighbors (ruggedcom only supports LLDP).
The issue is that randomly devices on the ruggedcoms will drop offline and then come back. The problem is that the devices that drop offline are all in the same VLAN, so it appears like a virus - i.e. one device drops off, then multiple. Eventually the HSRP starts flapping between the two 6500s and this causes havoc on the network.I'm almost to the point of taking a laptop and plugging it into one of the ruggedcom's to see traffic, but the issue is that the ruggedcoms are outside in cabinets that laptops shouldnt be exposed to.
Cisco Switching/Routing :: 6500 Ping Packet Drop From Core-Switch To Directly Connected Server
Oct 24, 2011I have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.
View 9 Replies View RelatedCisco :: Snmp Oids For Command Show Counters Interface Intx / Y Delta On Catalyst 6500
May 23, 2011I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
View 3 Replies View RelatedCisco Switching/Routing :: Show Command In ASR 1004 For Running Diagnostics
Aug 29, 2012is there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device. i was only able to find 'test interface' but haven't run this yet (currently in production).
View 5 Replies View RelatedCisco Switching/Routing :: Command To Show Physical Connection In 3660
Jun 19, 2012I am using cisco c3660 to act as Terminal Server for the communication of production machines in my company, recently there is a communication lost issue happen and its due to physical cable unplug from the machine. to troubleshoot for this issues i have to physically go inside my production area to check on it, as i understand from vendor we can check on the physical machine to see whether the LED light on the module is green or not, but in case of need to troubleshoot at night time, its time consuming as i need to travel back to company. is there any command that i can issue in the router c3660 to check on the physical connection between c3660 router and the production machine? the IOS version is IOS (tm) 3600 Software (C3660-I-M), Version 12.1(4)
View 3 Replies View RelatedCisco Switching/Routing :: Nexus 7000 SWACT Show Redundancy Command
Nov 9, 2012We have Nexus 7K recently installed few months back with 2 Sup (Slot 5 & Slot 6).Recently recevied mesaanges in monitoring servervia SNMP:Alarm : active unit removal caused an auto SWACT However, when checked there are no recent logs which may be linked to this alarm. The show redundancy command output shows that Sup in slot 5 is active which in slot 6 is Hot Standby.
View 1 Replies View RelatedCisco Switching/Routing :: C2960 Password-recovery Status Show Command
Feb 9, 2012I enabled the "no service password-recovery" command on my C2960 switch. All seems to work as discribed. Only issue I have is --- which show command is used to reveal if the password-recovery feature is enabled of disabled as the command doesn't show up in the running config after you enable it ?
NOTE: The command does show up in the C2960 switch in config t mode (unlike the IOS router 2800 series), but doesn't show up in the running-config after you enable or disable it.
On the 2800 series routers (latest IOS) in config t mode the command does not show up but if you type "no service passowrd-recovery" the command function correctly and it does list it in the running configuration.
Cisco Switching/Routing :: Equivalent Command To Show Int Summary On The Nexus 7000?
Nov 20, 2011tell me if there is an equivalent command to Show int Summary on the Nexus 7000?
eg
MYCISCOSW01#show int summary
*: interface is upIHQ: pkts in input hold queue IQD: pkts dropped from input queueOHQ: pkts in output hold queue OQD: pkts dropped from output queueRXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)TRTL: throttle count
[code]....
I find it a useful command on the 6500 to spot high traffic flows.
Cisco Switching/Routing :: Show IOS Logging Command When Catalyst 2960 Was Shut Down
Mar 29, 2012know Cisco IOS command, how to show when Catalyst 2960 was shut down (power off)?
View 2 Replies View RelatedCisco Switching/Routing :: 6500 Show Interface Status Output As VLAN
Mar 5, 2013I have a really weired thing happening on 6509 device with one of my customers.The device has a SUP 2 (MSFC2) with version 12.2.18SXF17B.
any VLAN interface once administratively down or simply down shows on "show interface status" output as VLAN.While it supposed to show "Routed". However once the port is up it is shows "routed" like it should.
Cisco Switching/Routing :: 6500 MSFC No IP Routing Command
Jun 2, 2012I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
Cisco Switching/Routing :: IP Routing Command In 6500?
Mar 16, 2013Where is the "ip routing" command in Cisco switch 6500 series?
is the ip routing enable by default accoridng to the: [URL]
Cisco Switching/Routing :: 6500 Clarification For Using Mac-address-table Synchronize Command
Jul 12, 2010We want to configure the "mac-address-table synchronize" command on our 6500 series switches to ensure that the CAM tables on our DFCs are in synch with the PFC on the supervisor modules. url...it is recommended that we disable the routed MAC purging with the mac-address-table aging-time 0 routed-mac global configuration command. What is a routed mac entry? Are there any issues with running that mac aging-time command?
We also plan to run this command "mac-address-table aging-time 14400" to keep our ARP and CAM tables on the same aging time to reduce unicast flooding on our network. Can we run this command with the "routed-mac" command above?
Cisco Switching/Routing :: WS-C6513 Command To Check 6500 Switch Performance / Resource Usage
Apr 25, 2013I am on a call right now troubleshooting some latency issue. The CPU usage on the sup card is low. Don't see any drops or input errors. I am aware that the switch and its modules have capability limits. Is there command I can run which will tell me if any module is overloaded or if the fabric/backplane is over utilized?My chassis is WS-C6513 and sup card is WS-SUP720-3B.
View 3 Replies View RelatedCisco Switching/Routing :: Convert Switch Port To Router Port On 6500
May 8, 2012On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
Cisco Switching/Routing :: 4500 How To Show Last Time A Port Was Active
Jun 28, 2012is there a way to show the last time a port was active/inactive on a catalyst 4500?
View 3 Replies View RelatedCisco Switching/Routing :: ASIC Chip Failing In Cat3750?
Jun 5, 2012I've just noticed an error I've never seen before in our switch logs. We have a stack of 6 Cat3750G-48TS-E switches. The first two in the stack have been up for just over a year and I've only just noticed this error. Thus far, I haven't noticed any symptoms - I just stumbled upon this error while checking for something else.
As far as I can tell, this has only popped up once and it was 2 days ago. Unfortunately, due to an incorrect firewall rule, our syslogs were not getting to our syslog server so I don't have any historical logs to check against, but it hasn't happened since.
The error I've seen is as follows:-
Jun 5 17:04:03.288: * ManagementInterfaceInitialized exception in port-asic 0 (N16FujitsuSwitch.com.au-2)
Jun 5 17:04:03.288: ***********************************************************
[Code].....
Cisco Switching/Routing :: 4500 L3 / 500 Invalid Port Command
Nov 14, 2012i just want to ask whether i should do some configurations or not on my cisco switch 4500 L3 regarding the error of 500 invalid port command when host try to access FTP active on to FTP server, i just did static route on gig interface with no switchport mode to that host network, all traffic type was allowed except the FTP with active mode?
View 7 Replies View RelatedCisco Switching/Routing :: 4507R Cannot Put Command HW-Module To Change GE Port
May 3, 2013i have 4507R with dual supervisors (WS-X4013+10GE) with IOS cat4500-ipbasek9-mz.122-46.SG.bin the supervisor module are in 3 and 4, and I want to connection port 5, but i have interface and line protocol down "inactive" error.
So I realized to use command "hw-module" to change the module to GE port. However, I am not able to use the command as" I cannot use the command "hw-module uplink" as well.
Cisco Switching/Routing :: 4510 - Command To See If Port Was Ever Up And Passed Traffic
Apr 24, 2012I am looking to find a command or counter to tell me if a cisco switch port on a 4510 was ever up and passed traffic. I want to shutdown all unused switchports on our access switches. But before I do that I need to make sure device is just not off or the person is away on vacation. If I do sh int interface, is there a counter I can reference.
View 4 Replies View RelatedCisco Switching/Routing :: 6500 Unexpected Packets On Port
Apr 17, 2012i have several cisco 6500 switches, and user switched connected to them.in my example i have a global service vlan, where some access ports are directly connected on the 6500, and this vlan is also allowed on the trunks to the access switch.
now i am connected with ma laptop on a access switch, where my port is in the same vlan. when i do a show mac address-table on my access port, i can see my own mac-address, nothing else.when i start wireshark to see the traffic, all i should see is traffic from or to my MAC, or broadcasts/multicasts.
But i can see other unicast traffic with different source/destination mac than mine.It seem slike these packets get broadcasted over the whole VLAN, but its no broadcast MAC nor IP.
Cisco Switching/Routing :: Catalyst 3546 XL / Switchport Port-security Command Not Available
Oct 26, 2011Im trying to follow along documentation i see via train single videos and some online resources. I am trying to enable port security.I have a Catalyst 3546 XL when i type in "rtr1# switchport ?""port-security" is not only of the options to choose from. I have already set this as an access port.
View 4 Replies View Related