Cisco Switching/Routing :: How Port-ASIC Mapping In Linecard WS-X6148-GE-TX
Dec 28, 2011how is port-ASIC mapping in linecard WS-X6148-GE-TX?
View 5 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Doubt About WS-X6148A-GE-TX Port-ASIC Mapping
Jan 4, 2012Can some clarify what is the Port-Asic mapping in WS-X6148A-GE-TX.
View 3 Replies View RelatedCisco Switching/Routing :: 3750G Port Grouping Per Asic
Jun 12, 2012I have a 48-port 3750G switch (model # WS-C3750G-48TS-S). How do I determine which ports are grouped per ASIC on the 3750G switch? For example, is the grouping ports 1-8 is serviced by ASIC 1, ports 9-16 is serviced by ASIC 2, ports 17-24 is serviced by ASIC 3, etc. If it exists, what is the IOS command to show the mapping of ports to ASIC?
View 2 Replies View RelatedCisco Switching/Routing :: Correct Number Of Port Asic In WS-X6704-LC
Jan 1, 2012Clarifying whats the correct # of port asic in WS-X6704-LC?According to the following link (Catalyst 6500 Architectural white paper): [URL]
"In the WS-X6704-10GE line card, there are two port ASICs each supporting 2 x 10 Gigabit Ethernet ports"
While in the document: Understanding Quality of Service on the Catalyst 6500 Switch: [URL]
Table 10.
WS-X6704
Number of 10 GE Ports 4
- QoS on 10-Gigabit Ethernet Line Cards (WS-X6704-10GE)
So whats correct? 4 port asic or 2 port asic?
# Port ASIC’s on the linecard 4
# Physical Ports per Port ASIC 1
Cisco Switching/Routing :: WS-CBS3120X-S - Sh Platform Port Asic Stats Drops
Dec 10, 2012In our environment we have some HP chassis, and with them there are blade switches. Lately, we've been seeing some drops on few servers connected on the blade switch ports. The switch model is WS-CBS3120X-S. And below is the tx drop for two interfaces ( where the servers are connected to).
sh platform port-asic stats drop gi1/0/11
Interface Gi1/0/11 TxQueue Drop Statistics
Queue 0
Weight 0 Frames 0
Weight 1 Frames 0
[Code]...
Cisco Switching/Routing :: 6500 - Show Platform Port-asic Stats Drop Command?
Feb 21, 2012On a 3750 you can do a show platform port-asic stats drop command. Is there a corresponding command for 6500 chassis?
View 7 Replies View RelatedCisco Switching/Routing :: Difference Between WS-X6148A-GE-TX And WS-X6148-GE-TX
Jun 6, 2012What is the different between WS-X6148A-GE-TX and WS-X6148-GE-TX ? Currently, I can not use MTU command on X6148 but can on X6148A.This two cards installed in cat6509E.
View 2 Replies View RelatedCisco Switching/Routing :: X6748 And NAM-2 Modules Inaccessible After Installing Linecard
Oct 8, 2012I've installed second WS-X6748-SFP linecard on my catalyst 6509 with sup720-3b and after that NAM-2 and IDSM-2 module become inaccessible from management network. I can only login with session slot N proc 1.When I execute #hw-module module 4 reset, modules become accessible.
#sh module from cat6509
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 48 CEF720 48 port 1000mb SFP WS-X6748-SFP SAL114670XW
3 48 48-port 100FX SFP Ethernet Module WS-X6148-FE-SFP SAL1201BZKF
4 48 CEF720 48 port 1000mb SFP WS-X6748-SFP SAL1625ETFJ
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1206FNGQ
6 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL1206FVFB
8 8 Intrusion Detection System WS-SVC-IDSM-2 SAD120502LR
9 8 Network Analysis Module WS-SVC-NAM-2 SAD120206LB
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 001e.4a3e.3b30 to 001e.4a3e.3b5f 1.10 12.2(14r)S5 12.2(18)SXF1 Ok
3 001e.4aea.e7b0 to 001e.4aea.e7df 3.3 8.4(1) 8.5(0.46)RFW Ok
4 5057.a895.bb84 to 5057.a895.bbb3 2.4 12.2(18r)S1 12.2(18)SXF1 Ok
5 001c.58d0.6dc4 to 001c.58d0.6dc7 5.6 8.5(2) 12.2(18)SXF1 Ok
6 0016.c848.3698 to 0016.c848.369b 5.6 8.5(2) 12.2(18)SXF1 Ok
8 001e.f7a1.54b0 to 001e.f7a1.54b7 6.3 7.2(1) 7.0(8)E4 Ok
9 001e.f72a.ba62 to 001e.f72a.ba69 4.3 7.2(1) 5.1(2) Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
2 Centralized Forwarding Card WS-F6700-CFC SAL114881B6 4.0 Ok
4 Centralized Forwarding Card WS-F6700-CFC SAL1624EGQS 4.1 Ok
5 Policy Feature Card 3 WS-F6K-PFC3B SAL1206FNZY 2.3 Ok
5 MSFC3 Daughterboard WS-SUP720 SAL1206FSFH 3.1 Ok
6 Policy Feature Card 3 WS-F6K-PFC3B SAL1206FP27 2.3 Ok
6 MSFC3 Daughterboard WS-SUP720 SAL1206FN26 3.1 Ok
8 IDS 2 accelerator board WS-SVC-IDSUPG ADBG7270048 2.5 Ok
cat6500 running 12.2(18)SXF12a ios...
Cisco Switching/Routing :: Are WS-X6148-GE-TX / WS-X6148A-GE-TX Compatible With WS-X6K-SUP1A-2GE
Mar 17, 2013Are the WS-X6148-GE-TX and WS-X6148A-GE-TX compatible with WS-X6K-SUP1A-2GE and Sub-Model WS-F6020A?
View 1 Replies View RelatedCisco Switching/Routing :: Cat4500-IPBASEK9-M / Catalyst 4503-E Linecard Support?
Mar 22, 2012I have a 4503-e with WS-X4013+TS supervisor and WS-X4548-GB-RJ45 card. I purchased a WS-X4648-RJ45-E card and installed but IOS says its unsupported. Supervisor is running 12.2(46)SG software and 12.2(31r)SGA firmware. Obviously I'm hoping this cars can be supported somehow. Do I need to upgrade software or firmware, or return the linecard and get equivalent supported card? Oh, system is running Catalyst 4500 L3 Switch Software. (cat4500-IPBASEK9-M)
View 6 Replies View RelatedCisco Switching/Routing :: Does The F2 Linecard (N7k-F248XP-25) On Nexus 7010 Support Layer 3
Jan 25, 2012I am sure that F1 linecards on Nexus weren’t able to support L3 functionality, so my query is does the F2 linecard (N7k-F248XP-25) on Nexus 7010 support Layer 3?
View 2 Replies View RelatedCisco Switching/Routing :: WS-F6K-FE48-AF (WS-X6148-21AF) Support With SUP720-10G
Jun 14, 2012Running WS-F6K-FE48-AF InlinePower daughtercards with SUP720-10G?
The release notes mention that the following daughtercards are supported:
WS-F6K-GE48-AF
WS-F6K-48-AF
[URL]
But, specifically, the WS-F6K-FE48-AF is not mentioned.
We need to upgrade the supervisor in multiple 6500 chassis full of WS-X6148-21AF modules with WS-F6K-FE48-AF daughtercards, and we want to make sure there are no compatibility issues.
Cisco Infrastructure :: Two WS-X6148 With Even / Odd Port Failure?
Feb 8, 2012I have two WS-X6148-45AF linecards here that have been out of use for quite some time. Upon inserting them in one of our 6509-E's I noticed that both had "Minor Error"s on their module diagnostics.
I would have just assumed that the cards were dead and requested replacements, but both cards have the *exact* same diagnostic errors, which only seem to effect every-other port. That's too much of a coincidence for me, so I figured I'd ask on the forums and see if I'm just missing something obvious before I assume the worst. Are these cards both somehow damaged in the exact same way? Or is there some config/compatibility issue that I haven't heard of?
relevant diagnostic output from one of the cards (Both outputs the same, no use posting twice) is below:
Router#show diagnostic result module 4
Current bootup diagnostic level: minimal
Module 4: 48-port 10/100 mb RJ45 SerialNo : SAL11391VUY
[Code].....
Cisco Switching/Routing :: ASIC Chip Failing In Cat3750?
Jun 5, 2012I've just noticed an error I've never seen before in our switch logs. We have a stack of 6 Cat3750G-48TS-E switches. The first two in the stack have been up for just over a year and I've only just noticed this error. Thus far, I haven't noticed any symptoms - I just stumbled upon this error while checking for something else.
As far as I can tell, this has only popped up once and it was 2 days ago. Unfortunately, due to an incorrect firewall rule, our syslogs were not getting to our syslog server so I don't have any historical logs to check against, but it hasn't happened since.
The error I've seen is as follows:-
Jun 5 17:04:03.288: * ManagementInterfaceInitialized exception in port-asic 0 (N16FujitsuSwitch.com.au-2)
Jun 5 17:04:03.288: ***********************************************************
[Code].....
Cisco Switching/Routing :: 6500 - Show Platform Capture ELAM Asic
May 29, 2012I know that an ELAM can be setup on a 6500 running ipservices 12.2(33)SXJ, however I noticed that following commands are not available on a 6500 router running advipservices 12.2(33)SXJ:show platform capture elam asic etc
So I wanted to know if there is an alternate way to setup an ELAM for troubleshooting purposes?
Cisco :: WS X6148A RJ45 ASIC / Port Group Utilization
Mar 8, 2012Is there a way to view the utilization on a WS-X6148A-RJ-45 ASIC/port group?
View 7 Replies View RelatedCisco Switching/Routing :: 1841 Static Nat Mapping
Jan 5, 2013I guess i am just getting old and forgot how this works, or i have an IOS load with an undocumented feature in it.A customer of ours wishes to have their exchange server appear to the outside world on a seperate IP address as their public pool address is.in the past this has not been an issue, however in the current configuration we are unable to get the source address to appear per the NAT statement it always sources on the overloaded IP. below is the relevant NAT config, am i missing something, or have i hit a IOS feature? [code] There is a 45% chance i have forgotten everything i learned on the NOC desk and a 50% chance that it is somethine really stupid and 5% IOS is broken
View 5 Replies View RelatedCisco Switching/Routing :: Mapping Of Vlans On WS-C3750E-48TD-S
May 2, 2012My question is about WS-C3750E-48TD-S and WS-C3750E-24TD-S Switches
What are the limitations of the mapping of VLANs on this device? Is it limited by number or by interface? Does the configuration of an interface has spread all interfaces ?
Cisco WAN :: 6509 / System Detected CRC Error Rate On Port ASIC Data Bus Exceed Fatal Threshold
Dec 7, 2010Recently I faced 1 issue in MLS 6509.MLS had all Gig modules in slots 6,7,8 taking System detected CRC error rate on port ASIC data bus exceed fatal threshold, ("System detected CRC error rate on port ASIC data bus exceed fatal threshold".) causing the module reset by the SUP. After this active SUP causing it to failover the standby. This process was continuing every few minutes resulting in the SUPs on MLS rolling.what could be the issue for Sup rolling reset?
View 1 Replies View RelatedCisco Firewall :: Port Mapping On ASA 5505?
Jun 6, 2011how do you enabled multiple port mapping on asa 5505? i want to use 1 static ip address for rdp connection for 15 users, and the port will start from 3390 to 3340.
View 4 Replies View RelatedCisco Switches :: SF200 Port Mapping Function
Mar 14, 2013i was able to configure (via SF200 web interface) a port mapping from port FE17 to FE7.i have supressed this port mapping.
when i try to reconfigure a port mapping from port FE17 to FE3. The SF200 web interface crash. the SF200 seems to reboot.
i have updated the SF200 firmware from V1.1.2.0 to V1.1.2.9.44.when i was able to configure (via SF200 web interface) a port mapping from port FE17 to FE7.But after having suppressed this port mapping again, i was not able to reconfigure a new port mapping from port FE1 to FE3 (the SF200 hangs).
TP-Link ADSL2+ Wireless :: Where Is PVC Ethernet Port Mapping In TD W8961ND
Jan 18, 2013Region : Vietnam
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 build 120524 rel 05221
ISP : VNPT
Where is the PVC Ethernet Port Mapping in TD W8961ND?
Cisco Switching/Routing :: Convert Switch Port To Router Port On 6500
May 8, 2012On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
Cisco Switching/Routing :: Enabling Port Security On C4507R Shuts Down Port
Aug 13, 2012I'm trying to enable port security on several 4507R's. When I try to configure a range of ports the switch will randomly put 1 or 2 in err-disable. It's different every time I apply the config to the same group of ports. However if I do them one at a time it seems to work. But I really don't want to configure 6 fully populated switches one port at a time. We also have a lot of 3750's and they gave me no problem using a port range. [code]
View 4 Replies View RelatedCisco Switching/Routing :: 7900 - Port Configuration With IP Phone And PC On Same Port
Jan 15, 2013We just installed a hosted VOIP system using Cisco 7900 series IP phones. We are having a strange issue with a few computers where they pull DHCP information from our VOIP provider's DHCP server on the Internet and not our LAN DHCP server.
The switchports areconfigured as: switchport mode access
My rationale behind this is that the phones would use CDP to get their VLAN info from the providers Cisco router and the PCs would just ride on the default VLAN. But this is not the case. Computers randomly keep getting DHCP info from the provider's router. Do I have to use voice vlan x and make the switchports trunks?
Cisco Switching / Routing :: 3560 - Management Port Used As Regular Port?
Jan 30, 2012I have an all gigE 3560. I don't use the management FE0 port on the back. I was thinking to use that for a 100Mbps WAN connection.
Seems to work just fine when I plugged in an test. But I am not routing across that link yet as I still need to setup the far end.
Is there any reason this would not work? I would like to not burn a gig port if the max throughput of the circuit is 100Mbps.
Cisco Switching/Routing :: Lose Lot Of Bandwidth Over Trunk Port (vs Access Port) 3750g
Feb 18, 2013I have a 3750g connected to a "core" switch stack of 7 other 3750g's via 2 GigE ports in a trunk. This is currently in a switchport mode access port- channel so only the default vlan data is sent over. Now we have a need due to physical location of these switches, to allow vlan20 (DMZ) from this 3750g to the switch stack. I will configure a few ports on the switch stack for vlan20 and they need to be able to talk to the stand alone 3750g.To do this I will change the port channel on both endpoints to
-switchport trunk ecapsulation dot1q
-switchport mode dynamic desirable
also making the appropriate change on the interfaces belonging to this trunk.My question is, now that its a trunk port that carries multiple VLANs, how much is the bandwidth reduced on that 2gbps link?I have a very active VLAN (10) on the stand alone switch, but on the core I'm not going to be assigning VLAN 10 to any ports. So does traffic from VLAN10 even come across the trunk (wasting bandwidth) if no ports on the core side are assigned to it? I really just need vlan 1 and 20 (for now).
Cisco Switching/Routing :: Shutdown Specific Port On 3750x And Monitor Port At Same Time?
Oct 23, 2011is it possible to shutdown a specific port on my 3750x and monitor this port at the same time .for example , im dealing with a mac authenticated network using port security , i want to shut down all the ports that are not used at the moment , however , if some one gets connected to the one of the shutdown ports i want to know the mac address of the user or atleast to know that i have someone who is just plugged in to the one of the shutdowned ports .
View 4 Replies View RelatedCisco Switching/Routing :: 3825 ISR - Traffic Route From Switch Port To Router Port
Jun 5, 2013I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
Cisco Switching/Routing :: 888w - Way To Change Usage Of ISDN Port To Normal RJ45 Port
Sep 25, 2012I have Cisco 800 series (888w) with BRI-ISDN port. Is there any way to change the usage of ISDN port to normal RJ45 port?I want to use this SOHO router to sharing connection.
View 0 Replies View RelatedCisco Switching/Routing :: 1700 - Setup For Connecting Router AUX Port To Switch Console Port
Feb 26, 2012I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies View RelatedCisco Switching/Routing :: 881W - IOS Port Forwarding Commands For Port Forwarding
Apr 7, 2013I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedCisco Switching/Routing :: 3550 / Routing Protocol Neighbor Between SVI And Routed Port?
Apr 18, 2012I have a collapsed core design with routed ports between all components. Access layer switches, data center switches, core/aggregation. All routed (no spanning-tree at all).Now...I have to add an IBM BladeCenter with a BNT layer 3 switch to my topology. However, those nasties don't seem to support routed ports.How can I have a routed port on my cisco switch and a standard access port on the BNT and still establish an adjacency with an SVI? I am running OSPF, but I am labbing this in my home lab with 2 x 3550s and EIGRP.
On SW2:
*Mar 1 00:57:00.711: EIGRP: Received HELLO on Vlan100 nbr 10.1.1.1
*Mar 1 00:57:00.711: AS 999, Flags 0x0, Seq 0/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
*Mar 1 00:57:02.303: EIGRP: Sending UPDATE on Vlan100 nbr 10.1.1.1, retry 9, RTO 5000 tid 0
*Mar 1 00:57:02.303: AS 999, Flags 0x1, Seq 17/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
[code].....