What is the different between WS-X6148A-GE-TX and WS-X6148-GE-TX ? Currently, I can not use MTU command on X6148 but can on X6148A.This two cards installed in cat6509E.
View 2 RepliesAre the WS-X6148-GE-TX and WS-X6148A-GE-TX compatible with WS-X6K-SUP1A-2GE and Sub-Model WS-F6020A?
View 1 Replies View RelatedCan some clarify what is the Port-Asic mapping in WS-X6148A-GE-TX.
View 3 Replies View Relatedhow is port-ASIC mapping in linecard WS-X6148-GE-TX?
View 5 Replies View RelatedRunning WS-F6K-FE48-AF InlinePower daughtercards with SUP720-10G?
The release notes mention that the following daughtercards are supported:
WS-F6K-GE48-AF
WS-F6K-48-AF
[URL]
But, specifically, the WS-F6K-FE48-AF is not mentioned.
We need to upgrade the supervisor in multiple 6500 chassis full of WS-X6148-21AF modules with WS-F6K-FE48-AF daughtercards, and we want to make sure there are no compatibility issues.
explain me the difference between FTE-10G and SFP-10G-SR, being focus on an architecture Nexus.
View 5 Replies View RelatedI found a 851 router and tried to build a ezvpn tunnel. The issue I am running into now is that a 851 router can only have one vlan in its database. I need two vlans to go into the EZvpn tunnel with using another device. So can you tell me if a 881 router can have more than one vlan created on the router and can those vlans be assigned to a interface and can I create a svi for each of those vlans as well.
View 2 Replies View Relatedwhat the difference betwen these two cards? SFP-10G-SR or SFP-10G-LR
View 2 Replies View Relatedwhat the difference between L2 Vs L3 VLAN? in know in which situation i use L2 Vlans but i don't know that about L3 Vlan.
View 2 Replies View Relatedi would like to check out what's the difference between the naming convnetion for the 6500 IOS.
I read the data sheet to support my POC deployment to support NCS v.1 the 6500 IOS need to upgrade to 12.2 (33) SXI
Is it able to work if i using SXJ instead of SXI, with the same IOS version 12.2 (33)?
I've acquired an 871W, because I'd like to use wireless, to replace my 851. I Ft Pd the 851's configuration to my FTP server and then Ft Pd this to the 871W. Save for the fact that this has a radio interface (currently shutdown), everything works save for FTP from the outside. I can not even telnet to port 21 of any of the internal FT servers. I can telnet to any other port (ssg, smtp, HTTP, https, etc.) but FTP will not pass. What's the difference?
View 12 Replies View RelatedWhat is the difference between Operating temperatue & storage temperature of switch C3560E ?
View 2 Replies View Relatedterms of Performance for 3925, 3925E and 3945.
didn't see much different between 3925 and 3925E except an additional port.
what is difference between Cisco catalyst 3750e 48 and SF300-48p.
View 3 Replies View RelatedI have a cisco WS-C3750G-24TS with IOS flash :/ c3750-mz.122-ipservicesk9-25.SEB4.bin "
I purchased a new Cisco WS-C3750X-24 with the IOS flash :/ c3750e-universalk9-mz.150-1.SE/c3750e-universalk9-mz.150-1.SE.bin. ( NEW )
When i configured a stack between the two 3750, the new switch restarted due the version mismatch (different IOS´s);
We have two versions:
WS-C3750G-24TS-ipservicesk9 flash :/ c3750-mz.122-25.SEB4.bin "
VS
WS-C3750X-24 flash :/ c3750e-universalk9-mz.150-1.SE/c3750e-universalk9-mz.150-1.SE.bin.
Is that possible to configure a stack between then?
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Tenho um cisco WS-C3750G-24TS com o IOS flash:/c3750-ipservicesk9-mz.1
22-25.SEB4.bin"
Adquiri um novo cisco WS-C3750X-24 com o IOS flash:/c3750e-universalk9-mz.150-1.SE/c3750e-universalk9-mz.150-1.SE.bin.
[code]...
What is the difference between IP Base and Universal for 3750X switches?
View 2 Replies View RelatedI will go to buy a core 4506 but I'm comfusing about the Sup engines and the Fiber module. What is the different between the Sup7 and Sup7L?in the fiber module that I will go to buy is it contain the SFP inside or I have to buy the SFP ( WS-X4612-SFP-E ). also what is the different between the SFP and GBIC?
View 4 Replies View RelatedSwitch A is: WS-C2960-48TC-S
Switch B is: SG 300-10MP
Neither switch supports a similiar transceiver module. We are looking at transceiver GLC-SX-MM for Switch A, and MGBSX1 for Switch B all the Layer-1 information (SX / wavelength, Multi Mode, etc.) I am able to find out about the two transceivers seems to match, so would there be any issue by having these 2 "different" transceivers at either end?
I want to choose a pair of switches for our data center.What I need: 48 x 1GE access ports, 2 x 10GE uplink ports.Nice feature of 3750-X is stacking. So what features has 4948-10GE? Why I should prefer that switch?
View 11 Replies View RelatedAre there any differences between the autoqos commands on a WS-C2960S switches (or in any other series)? Follow the commands:
- auto qos trust
- auto qos voip trust
I was checking the documentation on this link:
URL
And couldn't find any great difference between the two commands, as far as I could see they'll set the Ingress and Egress queues the same way.
Are there any differences between those two commands (auto qos trust and auto qos voip trust)? If so, when should I use one and the other?
What is the difference between sdm prefer access & sdm prefer default & sdm prefer lanbase-routing? When do we use these options?
View 2 Replies View RelatedIn my 6513 switch chassis we have two Supervisor Engines 720 one is marked Active other as Hot. what is the diffrence in their mode as by name I suppose that Active one is currently in use and Hot one is in standby mode.They are showing in this manner.
Module Ports Card Type
7 2 Supervisor Engine 720 (Active)
8 2 Supervisor Engine 720 (Hot)
what is the difference between Cisco Nexus switches and the usual catalyst 3750 switches.I do understand the operating system in both these are different.
When will we suggest using Cisco nexus instead of usual Cisco switches? Also what interface does Cisco nexus like 5548 come with , is it both copper and fiber?
Cisco let us try a CISCO C3750X- 24T-S Stack (2 switches) ->> IpBase Sofware licence We've 2 Hyper-v 2008 R2 and one SAN Netapp FAS2040 connected via Iscsi.All was working well with this stacks.Hyper-V see Nas Iscsi interface without problem. Even with basic stack config (no Vlan, ect...).Then, after this test period, we bought a C3750X-24T-L stack (2 switches) to replace the stack lent by Cisco.This one is LanBase Software.
With this stack, hyper-v work very bad ! We've got a lot of Iscsi error in the eventvwr.I can't access luns.So, is there a difference between LanBase and IpBase for a iscsi use ?I put the 24T-S config on the 24T-L switch without pb. So config is the same on both stacks...Also i've got a "TestPortAsicLoopback" = "Failed" on the new stack...I've tried with other stack cables. Not better.
What the different between using hsrp on vlan interface and on physical port (routed port) on Cisco 3750 Switch? Wha the benefits?
View 3 Replies View RelatedIs there a way to view the utilization on a WS-X6148A-RJ-45 ASIC/port group?
View 7 Replies View RelatedI have two WS-X6148-45AF linecards here that have been out of use for quite some time. Upon inserting them in one of our 6509-E's I noticed that both had "Minor Error"s on their module diagnostics.
I would have just assumed that the cards were dead and requested replacements, but both cards have the *exact* same diagnostic errors, which only seem to effect every-other port. That's too much of a coincidence for me, so I figured I'd ask on the forums and see if I'm just missing something obvious before I assume the worst. Are these cards both somehow damaged in the exact same way? Or is there some config/compatibility issue that I haven't heard of?
relevant diagnostic output from one of the cards (Both outputs the same, no use posting twice) is below:
Router#show diagnostic result module 4
Current bootup diagnostic level: minimal
Module 4: 48-port 10/100 mb RJ45 SerialNo : SAL11391VUY
[Code].....
We have ordered a N5548UPM-6N2248TP bundle. We would like to know if FET-10G sfp’s are included in this. let me know the difference between N5548UPM-6N2248TP and N5548UPM-6N2248TF bundle.
View 3 Replies View RelatedAny major difrrence between Netflow v/s Netflow-Lite?
I am trying to understand if Cisco 4948E can do the same job as Cisco 4500E or not and difference between Netflow v/s Netflow-Lite will work for me to select correct product.
I have found two line cards with this description installed in a Catalyst WS-4507R with Sup II+ (WS-X4013+):
WS-X4306 : 1000Base X (GBIC)
WS-X4306-GB: 1000Base X (GBIC)
Whats the difference between these modules? I cannot find information about part number "WS-X4306" Do these modules (WS-X4306 and WSX4306-GB) work with SUP7-E?
I see there are two different part numbers for Sup7-E. One has /2 at the end. So what's the difference between them?
View 2 Replies View RelatedI want to know what is the different between IOS of the catalyst WS-C2960-48PST-S and the IOS of catalyset WS-C2960-48PST-L.a want to upgrad the IOS of a WS-C2960-48PST-S with the IOS of WS-C2960-48PST-L (because this reference has a LANBASE version of IOS).
View 4 Replies View RelatedAny difference between A9K-RSP-4G and A9K-RSP-8G? What is the usage for additional 4GB memory?
View 8 Replies View Related