Cisco Switching/Routing :: Shutdown Specific Port On 3750x And Monitor Port At Same Time?
Oct 23, 2011
is it possible to shutdown a specific port on my 3750x and monitor this port at the same time .for example , im dealing with a mac authenticated network using port security , i want to shut down all the ports that are not used at the moment , however , if some one gets connected to the one of the shutdown ports i want to know the mac address of the user or atleast to know that i have someone who is just plugged in to the one of the shutdowned ports .
View 4 Replies
ADVERTISEMENT
May 6, 2013
I have a single 2960s without stack module. The stack port has a status of down, however I'd like to disable it so that it does not generate a false alarm in my NMS. The documentation states that there should be a command "switch 1 stack port 1 disable" but the switch (running 15.0(2)SE2) doesn't seem to be available. Is this a dcumentation bug or is the command not there at all?
View 2 Replies
View Related
Apr 9, 2013
a switch port is shutdown, but when i use NO SHUTDOWN command it is working and shows administratively down. like this command does not affect on it. i should enable this port? what can i do btw, port is not in errdisable and portfast is enabled.
View 3 Replies
View Related
Sep 26, 2012
on 7600 SUP720 3B.I have port channel and there are two ports on that port channel. is it possible to apply this command? does it work?
View 1 Replies
View Related
May 24, 2012
I would like to ask about 3750 stacking and some Cat6 stuff...
1) How do we monitor 3750 stacking port in LMS?
2) Let say if I stack 3 switches, middle switch should be Master. Uplink should be at Top and Bottom. Is best practice?
3) Can we mixed 3750G and 3750X and what is result internal BW - fallback to 32Gps?
4) is there any Qos difference between WS-X6816-10G-2T and WS-X6816-10G-2TXL?
5) is there any Qos difference between MSFC5 PFC4 and MSFC5 PFC4XL?
6) What is main difference between PFC4 and PFC4XL in Sup2T?
7) Pls share more about Central and Distributed Switching in Sup2T and which card support Distributed DFCXL?
View 3 Replies
View Related
Jul 6, 2012
I have an ASA 5520 and I'm using Solar winds real time interface tool to monitor the through put of the port. It seems I can never get it to use more than 100mb, where should I check?
I have run a sh int giga 0/1 and it shows the port is 1000mb full duplex and the I have also checked the other end where it plugs into the LAN and this also says the port is running at 1000mb full duplex.
View 1 Replies
View Related
Mar 18, 2013
when plugging a Cisco 7060 to the specific switch port it does not power on. The inline power consumption is abnormally high compared to the other phones that are plugged in, maybe double the amount.
non Poe devices work on the same port.
I used multiple cables and phones.
View 6 Replies
View Related
Oct 7, 2012
I have a network with 3 segments and a 2921 router.v172.16.5.0/24, 172.16.0.0/27 and 172.16.2.0/23 .
I want to block all 135 TCP traffic from/to IP 172.16.5.5 to any host in other segment, but only TCP port 135 and only to the specified IP.
View 2 Replies
View Related
Nov 11, 2010
What is the point of it? It is not a remote console. If i reboot the switch i cannot get back to the out of band management port unless the switch is fully running. Is this only for security purposees? so all telnet/ssh is from an Out of band network?
View 15 Replies
View Related
Dec 11, 2012
dont seem to be able to get policing working inbound on a port 3750X v 15.0(2)
Config is below:
ip access-list extended SMB
permit tcp host 192.168.1.14 host 172.16.1.30
permit tcp host 192.168.1.14 host 172.16.1.31
[Code]....
View 6 Replies
View Related
Jan 18, 2012
Ask this question, if someone came across a 6513, one of the RJ45 ports are constantly falling.The question is how to disable logging on a specific portno logging event link-status does not work.
View 1 Replies
View Related
Nov 5, 2011
We are using catalyst 2960S Lan Base IOS on Radio towers. We just bought 50 Accest points, thas are GPS synchronized. Problem is the APs need to be connected on L2-mac betwen each other. But at this time we are using port isolation on each switch (tower) by protected port function to isolate clients from each other.
My question is, is possible to specifi a Mac addresses in specific vlan thats can comunicate betwen protected ports? On tower is one Master unit and others are slave. I thing there is only 1 dirrection comunication - from master to slave.
View 2 Replies
View Related
Apr 10, 2012
Assume I had Catalyst 3560X/3750X with 24 ports. The partnumber is WS-C3560X-24P-LI would like to how is the numbering defined if the switches have a C3KX-NM-10G installed with 4 SFP-GE-L.
View 1 Replies
View Related
May 15, 2012
I would like to know if it possible to create a policy map in order to redirect the traffic ( 80 , http, 8080) to a proxy.
My current equipment its a 3750X using a IP Service License ,I was reviewing some options but i want to be sure before implement in production.
View 8 Replies
View Related
Oct 8, 2012
I want to limit the bandwidth going to remote site on the switch connecting to our netapp.We have a 4 port channel group setup on our 3750x switch going to our netapp storage. We have a Wan 100mb link to our remote site and we want only 60MBs of that link to be used for Netapp traffic all other local traffic needs to use the full amount of the bandwidth to the netapp.
Is possible to allocate bandwidth in this way and how would I go about this? We dont have access to the routers for the link and they plug directly into a port on our cisco.
View 3 Replies
View Related
Dec 11, 2012
We purchased a number of 3750X 48 and 24 port switches for the College Campus. Am finally getting around to getting them inserted on the network. Working with a WS-3750X-48PF-S and a WS-3750X-24P-L. Have them stacked with the 10Gb uplink on the 48 port switch. Have not been having fun.In the boot sequence, the switches recognize they are stacked, but as soon as they finish boot, I get the message on the 48 port switch: “Stack Port 1 Switch 1 has changed to state down.” Then “Stack Port 2 Switch1 has changed to state down.” Am noticing that I have a message preceding that: “Major version mismatch with stack neighbor.”The 48 port is running c3750e-universalk9-mz.150-1.SE3, HBOOT 12.2(53r)SE2.The 24 port is running c3750e-unversalk9-mz.122-55.SE3, HBOOT 12.2(53r)SE2Most of our 3750X and older switches are running 122-55 or 122.58 code. IP base or Universal. There is speculation that the problem is the 24 Port is Lan base, as the part number might indicate. (WS-C3750X-24-P-L.... I think that is the part number) and the 48 is IP base. Both switches are Universal, and my understanding is that they don't care about LAN or IP Base until you enable a function that falls in the IP Base domain. Then I have to call Cisco Licensing.For these switches, LAN Base is fine, based on the boot message, I feel the real problem is 122-55 versus 150-1 in the stack. So.. the question is: Do I downgrade the 48 port to match what we have in our environment, and what is on the 24 port switch. Or... Upgrade the 24 port switch to match the 48 port switch and have an installation that is not consistent with our environment? I do have two more edge closets to install with this purchase of 3750X 48 port switches.
View 2 Replies
View Related
May 20, 2013
I have cisco 2651. It contains two FastEthernet interfaces: Fa0/0, Fa0/1.Fa0/1 has an ip address. Fa0/0 hasn't an ip address.I need to create monitor session from source Fa0/1 to destination Fa0/0. Then i want to connect my notebook to Fa0/0 to analyze some traffic from port Fa0/1
View 2 Replies
View Related
Oct 10, 2012
I am trying to filter ARP answer arriving on a C6500 trunk port, for a specific vlan.Filtering conditions are:
- packet arrive from vlan ID x on the trunk (on only for this vlan ID)
- source MAC address = xx:xx:xx:xx:xx:xx
Thae aim is that the C6500 with never enter into its CAM table this MAC address.I looked at several methos like service policy or vlan filter, but no solution for the moment.
View 3 Replies
View Related
Jan 15, 2012
What I am attempting to achieve is to aggregate trunk ports out of a VMware server into a single logical connection to give as much bandwidth as possible, the switches are 3750X and are three stacked together with the server connections spread across the stack. What I am not sure about is if two port channel load balance protocols can happy co-exist on the switch, by default the switch is using MAC address load balancing and Vmware wants to use IP Source load balancing. As other trunks and channels exist on the switch I don't want to make a change that will affect the other live connections if changing this is a global setting and not local on the channel.
View 2 Replies
View Related
Feb 26, 2012
Possible to configure multichassis port-channel between a VSS and 3750X (Port-channel not in the same switch on the 3750X stack). I got it using LACP but I need Pagp to get VSL redundancy “dual-active detection pagp trust channel-group 1”. I am using the last VSS IOS version 15.0(1)SY. I can’t get the option “switch 1 preempt”, has it changed with other option?
View 2 Replies
View Related
Jun 19, 2012
I'm trying to get an IP_ADDR set on the management port in SWITCH: mode but for some reason the port seems disabled. PC shows connection unplugged. MGMT_INIT is not a valid command (not listed under '?' ). Bootloader version is 12.2(53R)SE2 FC1.
View 4 Replies
View Related
Jan 29, 2013
I need to tear down an existing port-channel on a 3750X running c3750e-universalk9-mz.150-1.SE3.bin. This port channel is currently down down. It has three ports in it that will be added one each to three existing port-channels, I am assuming as long as the "channel-group" command is exactly the same as it is on the three existing port-channels I should be ok just adding the new port. One point to note is that the three existing port-channels all have three ports so this will be adding the fourth port to each port-channel. I know after reading that it is a best practice for load balancing to use either 2, 4, or 8 ports for a port-channel. Also what is the command to see all ports that are in a port channel?
View 1 Replies
View Related
Mar 17, 2013
Is it possible to connect 3750X with C3KX-NM-10G to X2 10G port on sup2t in 6500E switch.There is Cisco OneX Converter Module, but I could not find that it is supported on sup2t.
View 2 Replies
View Related
Nov 2, 2011
Is it possible to configure the span(switch port analyzer) port and restrict it to only listen to ingress and egress of TCP/1433 from the source port?
View 2 Replies
View Related
Feb 18, 2013
I have two stacks 3750X on two different sites with two links L_2_L, and I want to configure the port channel to aggregate the two links.
Site A Site B
3750X -A1 --------------------------------------( )--------------------------------------- 3750X -B1
( L-2-L )
3750X -A2 --------------------------------------( )--------------------------------------- 3750X -B2
Below the configuration that I have put the two stacks.
site A
interface Port-channel5
description Etherchannel group entre le stack 3750X-A et Switch Lan_2_Lan
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 11,12,999
switchport mode trunk
switchport nonegotiate
speed 100
But the problem is only one link is Bundeled in channel group, see below
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
5 Po5(SU) LACP Gi1/0/15(I) Gi2/0/15(P)
View 8 Replies
View Related
Jun 28, 2012
is there a way to show the last time a port was active/inactive on a catalyst 4500?
View 3 Replies
View Related
Jul 10, 2012
I have a pair of 3560's configured with dot1q trunks between them carrying a number of VLANs.
Once deployed there will be a requirement for these physical trunks to be disconnected from time to time. Knowing that this is inevitable I am trying to minimise the period of time for the trunks to recover once the physical connectivity is reinstated.
All of the VLANs on the switches are configured for Spanning Tree Rapid PVST. Current time for the trunks/VLANs to come up is around the 4 second mark.
View 11 Replies
View Related
Mar 14, 2012
i have a VSS core that has 4 downstream links to 4 stacked switches. I connected each of the 4 links to different switch in the switch stack. I then created a port-channel that combines all the links from each switch. Is there any issues associated with this setup?
View 9 Replies
View Related
Apr 17, 2013
I have a DHCP server for a subnet that has only lightweight WAP's in it. The DHCP server is running on the gateway for this subnet which is a 3750X 2 switch stack running 12.2(53r)se2.I have the following configured:
ip dhcp excluded-address 10.1.10.161 10.1.10.162
ip dhcp pool DHCP-VL20
network 10.1.10.160 255.255.255.224
domain-name mydomain.net
dns-server 10.11.11.30 10.11.11.40
default-router 10.1.10.161
ease 3
The server hands out up to 18 IP addresses and no more, with 20 devices on the subnet. Scanning the subnet with a 3rd party network management system I see the following IP's never get handed out or used:
10.1.10.161 - 162 (manually excluded)
10.1.10.167 - 168
10.1.10.171 - 176
10.1.10.178
and of course 2 IP's I have manually excluded, 11 IP's in all that wont get handed out. It should only be 2 that don't get handed out. I've double and triple checked the exclusion and thats the only one. so I run a 'sh ip dhcp pool' and see this:
Pool DHCP-VL20 :
Utilization mark (high/low) : 100 / 0
Subnet size (first/next) : 0 / 0
Total addresses : 30
[code]....
[edit]I should also mention that "sh ip dhcp bind" does not show these randomly excluded IP's in use. They also do not show up in any arp table I can find.I have looked all over the config and I cant find where these extra 9 addresses are being excluded. how to free up these 9 seemingly random exclusions? Haven't issued a reload and I haven't deleted and rebuilt the DHCP server yet, production network.
View 2 Replies
View Related
Oct 25, 2011
I use a router RV082 with load balancing. My problem is when I try to access a specific site, I get the error message that my IP address changes and I can not use 2 ip address. I want to specify an ip range to always use the same WAN port.
View 2 Replies
View Related
Jul 1, 2012
Is it possible to enable an absolute value rate limit using QOS on a HP ProCurve 5406 switch for a particular IP range on a specific port? Is there a way to configure our HP 5406 with an absolute rate limit on "WAN" port for that server's IP range? I would like to limit it to only being capable of sending 1Mbps worth of traffic over the head end at once.Everything in the documentation points towards priority queues, which as far as I can tell, isn't really what I want.Baring accomplishing this goal using rate limiting is there a better way to prevent our services from accidentally saturating this connection?i thimkong about somthing like that:
class ipv4 rate-limit-port-A1
match ip 10.136.0.0/16 any
exit
policy qos port-a1-ratelimit
class servers-to-be-slowed action rate-limit kbps 1000
exit
interface A1 service-policy port-a1-ratelimit inI'm not sure about this.
View 4 Replies
View Related
May 8, 2012
On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
View 3 Replies
View Related
Aug 13, 2012
I'm trying to enable port security on several 4507R's. When I try to configure a range of ports the switch will randomly put 1 or 2 in err-disable. It's different every time I apply the config to the same group of ports. However if I do them one at a time it seems to work. But I really don't want to configure 6 fully populated switches one port at a time. We also have a lot of 3750's and they gave me no problem using a port range. [code]
View 4 Replies
View Related
