Cisco Switching/Routing :: X6748 And NAM-2 Modules Inaccessible After Installing Linecard
Oct 8, 2012
I've installed second WS-X6748-SFP linecard on my catalyst 6509 with sup720-3b and after that NAM-2 and IDSM-2 module become inaccessible from management network. I can only login with session slot N proc 1.When I execute #hw-module module 4 reset, modules become accessible.
#sh module from cat6509
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 48 CEF720 48 port 1000mb SFP WS-X6748-SFP SAL114670XW
3 48 48-port 100FX SFP Ethernet Module WS-X6148-FE-SFP SAL1201BZKF
4 48 CEF720 48 port 1000mb SFP WS-X6748-SFP SAL1625ETFJ
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1206FNGQ
6 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL1206FVFB
8 8 Intrusion Detection System WS-SVC-IDSM-2 SAD120502LR
9 8 Network Analysis Module WS-SVC-NAM-2 SAD120206LB
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 001e.4a3e.3b30 to 001e.4a3e.3b5f 1.10 12.2(14r)S5 12.2(18)SXF1 Ok
3 001e.4aea.e7b0 to 001e.4aea.e7df 3.3 8.4(1) 8.5(0.46)RFW Ok
4 5057.a895.bb84 to 5057.a895.bbb3 2.4 12.2(18r)S1 12.2(18)SXF1 Ok
5 001c.58d0.6dc4 to 001c.58d0.6dc7 5.6 8.5(2) 12.2(18)SXF1 Ok
6 0016.c848.3698 to 0016.c848.369b 5.6 8.5(2) 12.2(18)SXF1 Ok
8 001e.f7a1.54b0 to 001e.f7a1.54b7 6.3 7.2(1) 7.0(8)E4 Ok
9 001e.f72a.ba62 to 001e.f72a.ba69 4.3 7.2(1) 5.1(2) Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
2 Centralized Forwarding Card WS-F6700-CFC SAL114881B6 4.0 Ok
4 Centralized Forwarding Card WS-F6700-CFC SAL1624EGQS 4.1 Ok
5 Policy Feature Card 3 WS-F6K-PFC3B SAL1206FNZY 2.3 Ok
5 MSFC3 Daughterboard WS-SUP720 SAL1206FSFH 3.1 Ok
6 Policy Feature Card 3 WS-F6K-PFC3B SAL1206FP27 2.3 Ok
6 MSFC3 Daughterboard WS-SUP720 SAL1206FN26 3.1 Ok
8 IDS 2 accelerator board WS-SVC-IDSUPG ADBG7270048 2.5 Ok
cat6500 running 12.2(18)SXF12a ios...
View 8 Replies
ADVERTISEMENT
Dec 28, 2011
how is port-ASIC mapping in linecard WS-X6148-GE-TX?
View 5 Replies
View Related
Mar 22, 2012
I have a 4503-e with WS-X4013+TS supervisor and WS-X4548-GB-RJ45 card. I purchased a WS-X4648-RJ45-E card and installed but IOS says its unsupported. Supervisor is running 12.2(46)SG software and 12.2(31r)SGA firmware. Obviously I'm hoping this cars can be supported somehow. Do I need to upgrade software or firmware, or return the linecard and get equivalent supported card? Oh, system is running Catalyst 4500 L3 Switch Software. (cat4500-IPBASEK9-M)
View 6 Replies
View Related
Jan 25, 2012
I am sure that F1 linecards on Nexus weren’t able to support L3 functionality, so my query is does the F2 linecard (N7k-F248XP-25) on Nexus 7010 support Layer 3?
View 2 Replies
View Related
May 13, 2013
I have a WS-X6748-GE-TX with the WS-F6700-CFC daughter card. Is it possible to replace the WS-F6700-CFC daughter card with a WS-F6K-DFC4-AXL to make this compatible with the SUP-2T? Or, are there differences between the CFC and DFC base modules?
View 11 Replies
View Related
Aug 19, 2012
I have a cisco 6509 switch in which i have 2 SUPs. I am using 3 Qty. of WS-X6748-GE-TX in the same switch. First 24 ports of module 1 and are not working. I replace the faulty moldule with the working one but now the new (good) module's first 12 ports stopped working. But when I insert the good card (the replaced one with the faulty) in other chassis it works fine.
View 2 Replies
View Related
Feb 7, 2012
We are upgrading two standalone 6509E chassis to a VSS system with new VS-S720-10G-3C cards. The 6509's have WS-X6748-GE-TX card with DFC3B daughter cards (see below). The compatablity matrix (see below) states that 67xx cards are supported but it goes on to state DFC3C or DFC3CXL cards are needed. So does this mean that the existing WS-X6748-GE-TX cards have to be upgraded or will they be supported?
Core #1Mod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 48 CEF720 48 port 1000mb SFP WS-X6748-SFP SAL 2 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAD 5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL 6 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL 7 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL 8 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL
[code]....
View 3 Replies
View Related
Jan 28, 2013
its a hardware problem or just not get power to module 1 for module WS-X6748-GE-TX? this is the capture from show module and sh log :
------------------ show module ------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX xxx
5 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE xxx
Mod MAC addresses Hw Fw Sw Status
[code].....
View 4 Replies
View Related
Oct 18, 2012
I urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?
View 1 Replies
View Related
Dec 7, 2011
in my C6506-E installed module WS-X6748-SFP with WS-F6700-DFC3BXL
last time a see errors:
18:42:49: %DIAG-SP-6-TEST_RUNNING: Module 3: Running TestAclPermit{ID=23} ...
18:42:51: %DIAG-SP-3-TEST_FAIL: Module 3: TestAclPermit{ID=23} has failed. Error code = 0x1
23) TestAclPermit -------------------> F
Current bootup diagnostic level: minimal
Module 3:
Overall Diagnostic Result for Module 3 : MINOR ERROR
Diagnostic level at card bootup: minimal
[code]...
View 4 Replies
View Related
Nov 21, 2012
currenly running a C6509E, with a WS-SUP720-3B running IOS level S72033-adventerprisek9_wan-MZ.122-22.SXH3. I want to install a WS-X6748-GE-TX blade and would like NOT to have to upgrade IOS at this time. Future migrations are planned. Can this be done?
View 6 Replies
View Related
Oct 2, 2011
we have a 6509 with ios 12.2.33SXJ
we have 2 WS-X6516-GE-TX, WS-X6516A-GBIC, and a WS-X6748-GE-TX with a WS-F6700-CFC daughtercard
our sup is a WS-SUP720-3B
we are experiencing packet loss for everything connected in the WS-X6748-GE-TX blade, right now we dont have any production device in that blade due to the packet loss we are experiencing.
this switch was running hybrid before it is now running native ios, however I can't recall if we didn't have that packet loss before. do i need to update a firmware of the card or daughtercard (if this is possible, can't say i've done it before).
View 10 Replies
View Related
Nov 13, 2012
I have one Cisco 7606 and i need to install a WS-X6748-GE-TX with WS-F6700-DFC3CXL.When I install the WS-X6748-GE-TX the module is powered off with the following warning:
00:01:45: %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 1, power not allowed: Unsupported baseboard/earl combination. [code]
View 1 Replies
View Related
Mar 26, 2013
I have this 3750 stack where all ports are configured as below.The data runs on VLAN 1 and the voice runs on VLAN 100.
interface FastEthernet1/0/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,100
switchport mode trunk
Name: Fa1/0/1
Switchport: Enabled
Administrative Mode: trunk
[code]....
The PCs and Polycom VOIP phones are plugged into the switch and they work fine.However, if I plug printer(s) into the ports, they cannot be accessed.I have to end up removing the trunk mode before it can work like below.
Name: Fa2/0/43
Switchport: Enabled
Administrative Mode: dynamic auto
Operational Mode: static access
Administrative Trunking Encapsulation: negotiate
Operational Trunking Encapsulation: native
[code]....
View 12 Replies
View Related
Dec 1, 2012
I have a server with 4 ethernet ports, 1G, they are bonded together, two of them was pluged into cat6500 module WS-X6724-TX. now we have moved the two ports to the replace module WS-X6748-GE-TX.
I have checked server side, the bond configuration are same no changed. what is possible reason replace module will cause link offline? why "sh run all" give the port is shutdown?
View 8 Replies
View Related
Feb 7, 2013
I have a WS-C4510R+E with
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 48 10/100/1000BaseT Premium POE E Series WS-X4748-RJ45V+E CAT1612L1JD
2 48 10/100/1000BaseT Premium POE E Series WS-X4748-RJ45V+E CAT1612L1JW
3 12 10GE SFP+ WS-X4712-SFP+E CAT1622L0SC
4 12 10GE SFP+ WS-X4712-SFP+E CAT1622L0RM
5 4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7-E CAT1620L1UJ
6 4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7-E CAT1620L1Z2
Can i add two WS-X4712-SFP+E and two 10 GE ethernet module also?
Is there 10GE ethernet module with WS-C4510R+E.
View 2 Replies
View Related
Dec 14, 2011
Here i have a customer who has 7609 router with modules
ws-+6748-ge-tx
ws-svc-wism-1-k9
ws-sup720-3b
ws-sup720-3b
ws-svc-wism-1-k9
ws-6724-sfp
ws-x6704=10ge
ws-x6724-sfp
will this modules will be supported to the new chaisis ios or in the chaisis 7609S
View 1 Replies
View Related
Oct 29, 2012
we have a chassis 6513-E and a module WS-X6748-GE-TX, I'd like to know if could I put this module in any slot, since the documentation from Cisco says that any slot from a chassis 6500-E Series can support this module. And then in the documentation of WS-X6748-GE-TX says that this module is not compatible in the slots 1-8 of the 6513 chassis, only from 9th to 13th slots, in those slots from the 6513-E we already have 4x WS-X6748-GE-TX, and we'd like to know if could we put the module in the rest of the slots. The 6513, and 6513-E is kind of confusing.
View 4 Replies
View Related
Nov 23, 2012
we have a old Nexus 5010 running version 5.0(3)N1(1)it is in a franckenblock(like frankenstein) ie . we bought the parts and create our own system design before VCE was created. He have since bought VCE V block for our production sites. we use the franc ken block to test before we migrate to the production v block 300 FIX the issue we have is the 5010 will only see two 1 Gb/s SFP fiber modules in the first 12 slots. All these slots are dual 1g/10G. If we add more than two, it claims not to see them. We tried swapping the sfp and using both sfg-GE-MM and GLC-SX-MM moduels, no difference at all 1g sfp are in the first 5 slots. only the first two slots are up.the others say "Link not connected" or "SFP not inserted"all five links are the same SFP and are plugged in other switches.the green link lights are on plugged in SFP, even when the CLI states they are not plugged uni tried both two types of 1 Gb/s SFP. sfg-GE-MM and GLC-SX-MM ,i move the sfp between slot 1,2 and 3,4,5. nothing changed,From "sh int brief" you can see that it can see the sfp ie they are all 1Gfrom "sh int status " it sees 1g but why does it say type 10G?why when i go to the "int e 1/5" and try switch port mode now, it can't mode and trunk at now there (;also how to i stop or clear EU51 %SYSMGR-2-TMP_DIR_FULL: System temporary directory usage is unexpectedly high at 87%.i put as much info in the attached file as i could.
View 1 Replies
View Related
Mar 4, 2013
I am having issues trying to combine two modules into one VDC. The modules are as mentioned below: When I try to combine module 1 & 10 as shown above, the nexus 7000 switch displays 'Not compatible'. I've read the online guide and it mentions that the F2 and M1 module cannot be combine into the same VDC. Problem is, my customer has already purchased the module, how do i solve this problem? If I separate the VDC, how does module 1 talk to module 10 if user wants to send traffic to Internet or Server Farm?
View 3 Replies
View Related
Sep 17, 2012
Is it possible to implement LLQ(QoS) on ethernet modules in the Cat 6500? For this feature, I can only find documentation about ES+ modules or SPA/SIP modules! (according to the feature navigator LLQ is supporten on the concerning HW and SW image)
View 2 Replies
View Related
Apr 29, 2013
I am working on a project to connect 2 switch stacks via 10 Gb fiber. I am told that the 3750Xs do not natively receive the 10 GB SFPs. What part numbers do i need to order to make this work? Is there any IOS image requirements?
View 14 Replies
View Related
Mar 11, 2013
is there a command that gives me the model and serial number of the GBIC modules inside the modules of the Cisco 6500 (IOS)?
View 7 Replies
View Related
Dec 12, 2012
While configuring PoE Ethernet EHWIC PoE modules with ISR G2 routers Cisco DCT gives a warning to select AC Power Supply with PoE ‘PWR-3900-POE’. Do we need to select the PoE power supply for Enhanced EtherSwitch SM PoE modules also (at present it does nt show any warnings)?
View 1 Replies
View Related
Jun 3, 2013
I have already understood the following notice for using VSS function with 6700 series modules.For example there is the compatibility HW revision issue between the 6700 line card and CFC or DFC and so on. [code]
View 1 Replies
View Related
Nov 15, 2011
how to identify which modules are supported by cisco catalyst 6500. is there any OID which can give us the information
View 2 Replies
View Related
Sep 5, 2012
our network is spread over 15 floors and each floor we have 5-6 switches. we are planning to purchase cat3750-x 24 ps poe with C3KX-NM-10G network modules. Each floor has two up links to the core switch with single mode fiber and other being the multimode.Suppose if we are purchasing 75 switches do we have to purchase 75 C3KX-NM-10 G modules.? or can we limit our purchase with 15 C3KX-NM-10G sothat two uplinks from each floor can be made? since network modules are optional cost factor is invovled. Or any issue with stacking ? the SFPs will be LR and LRM MODULES.looking for an answer ? whether the new usb type console cable comes bundled with cat350x or shall we have to order separately?
View 7 Replies
View Related
Jan 23, 2011
We currently have two 6509's running in VSS, both switches have a WS-6748-GE module in slot 3. I'm in the processing of removing these modules. I will then be replacing them with a different module type, but I need to know how to remove the old configuration of the previous modules.
View 4 Replies
View Related
Feb 5, 2012
How to configure my serial modules on my 2600 and 3640? Each router has the WIC-2T with two cables connecting them. I tried to ping one router from the other, but no luck. Serial IP address I just made up, this is my home lab, so if I messed those up some how,
Here is the running config for each rotuer:
2610:
Current configuration : 1071 bytes
!
version 12.3
[Code]...
View 22 Replies
View Related
Apr 22, 2012
I have a question. I have a 6500 with two supervosrs and they both have CATOS. One of them failed and I need to replace. As long as the hardware is the same does the CATOS have to be indentical or can this be different.
View 4 Replies
View Related
Jun 13, 2012
We have many 3750E's and need to use Finisar X2 modules FTLX8541E2. After 15.0(1) IOS upgrade the 3750's now recognize the Cisco part X2-10GB-LRM's, but will not recognize our Finisar modules.
View 1 Replies
View Related
Oct 14, 2012
I recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.
View 1 Replies
View Related
Mar 20, 2012
How to get fiber optic modules for Cisco 2821 series router. I can not find anything apart a SFP module which contains only one SFP port.
View 9 Replies
View Related
