Cisco Switching/Routing :: C6506-E / TestAclPermit Fail In WS-X6748-SFP?

Dec 7, 2011

in my C6506-E installed module WS-X6748-SFP with WS-F6700-DFC3BXL
 
last time a see errors:

18:42:49: %DIAG-SP-6-TEST_RUNNING: Module 3: Running TestAclPermit{ID=23} ...
18:42:51: %DIAG-SP-3-TEST_FAIL: Module 3: TestAclPermit{ID=23} has failed. Error code = 0x1
  23) TestAclPermit -------------------> F
 Current bootup diagnostic level: minimal
Module 3:
Overall Diagnostic Result for Module 3 : MINOR ERROR
Diagnostic level at card bootup: minimal

[code]...

View 4 Replies


ADVERTISEMENT

Cisco Switching/Routing :: C6506 Module Cannot Be Detected

Dec 3, 2011

My C6506 USING ws-sup720-3B, i upgrade the IOS to the latest release of 12.2(33) SXJ1 IOS version. After upgrade and reload the machine got one module cannot be detect..WS-X6416-GE-MT, 16 port 1000mb MTRK ethernet module. The version of this are:

-HW 1.0
-FW 5.3 (1)1
-SW 8.5 (0.46) RFW
 
Question 1: Any tools available on cisco to check out the hardware/software compabiity feature?
 
Question 2: Any release note, compability matrix table etc resources.

View 1 Replies View Related

Cisco Switching/Routing :: WS-X6708-10G-3CXL Doesn't Work On WS-C6506-E

Oct 27, 2012

we can't start WS-X6708-10G-3CXL on WS-C6506-E. [code] we did try on conf t mode "power enable module 3" and it didn't work. [code]

View 2 Replies View Related

Cisco Switching/Routing :: WS-X6748-GE-TX And SUP-2T Compatibility?

May 13, 2013

I have a WS-X6748-GE-TX with the WS-F6700-CFC daughter card. Is it possible to replace the WS-F6700-CFC daughter card with a WS-F6K-DFC4-AXL to make this compatible with the SUP-2T? Or, are there differences between the CFC and DFC base modules?

View 11 Replies View Related

Cisco Switching/Routing :: First 12 Ports Of X6748 TX Are Not Working

Aug 19, 2012

I have a cisco 6509 switch in which i have 2 SUPs. I am using 3 Qty. of WS-X6748-GE-TX in the same switch. First 24 ports of module 1 and are not working. I replace the faulty moldule with the working one but now the new (good) module's first 12 ports stopped working. But when I insert the good card (the replaced one with the faulty) in other chassis it works fine.

View 2 Replies View Related

Cisco Switching/Routing :: VSS With VS-S720-10G-3C And WS-X6748-GE-TX Compatibility?

Feb 7, 2012

We are upgrading two standalone 6509E chassis to a VSS system with new VS-S720-10G-3C cards.  The 6509's have WS-X6748-GE-TX card with DFC3B daughter cards (see below).  The compatablity matrix (see below) states that 67xx cards are supported but it goes on to state DFC3C or DFC3CXL cards are needed.  So does this mean that the existing WS-X6748-GE-TX cards have to be upgraded or will they be supported? 

Core #1Mod Ports Card Type                              Model              Serial No.--- ----- -------------------------------------- ------------------ -----------  1   48  CEF720 48 port 1000mb SFP              WS-X6748-SFP       SAL  2    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE      SAD  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL  6    2  Supervisor Engine 720 (Hot)            WS-SUP720-3B       SAL  7   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL  8   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL

[code]....

View 3 Replies View Related

Cisco Switching/Routing :: Getting Module WS-X6748-GE-TX PWRDown On 7606?

Jan 28, 2013

its a hardware problem or just not get power to module 1 for module WS-X6748-GE-TX? this is the capture from show module and sh log :
 
------------------ show module ------------------
  
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     xxx
  5    2  Route Switch Processor 720 (Active)    RSP720-3CXL-GE     xxx
Mod MAC addresses                       Hw    Fw           Sw           Status

[code].....

View 4 Replies View Related

Cisco Switching/Routing :: To Replace A Line Card WS-X6748-SFP

Oct 18, 2012

I urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?

View 1 Replies View Related

Cisco Switching/Routing :: IOS Level Support Required For WS-X6748-GE-TX?

Nov 21, 2012

currenly running a C6509E, with a WS-SUP720-3B running IOS level S72033-adventerprisek9_wan-MZ.122-22.SXH3.  I want to install a WS-X6748-GE-TX blade and would like NOT to have to upgrade IOS at this time.  Future migrations are planned.  Can this be done? 

View 6 Replies View Related

Cisco Switching/Routing :: 6500 Packet Loss On Blade WS-X6748-GE-TX

Oct 2, 2011

we have a 6509 with ios 12.2.33SXJ
 
we have 2 WS-X6516-GE-TX, WS-X6516A-GBIC, and a WS-X6748-GE-TX with a WS-F6700-CFC daughtercard
 
our sup is a WS-SUP720-3B
 
we are experiencing packet loss for everything connected in the WS-X6748-GE-TX blade, right now we dont have any production device in that blade due to the packet loss we are experiencing.
 
this switch was running hybrid  before it is now running native ios, however I can't recall if we didn't have that packet loss before. do i need to update a firmware of the card or daughtercard (if this is possible, can't say i've done it before).

View 10 Replies View Related

Cisco Switching/Routing :: 7606 Need To Install WS-X6748-GE-TX With WS-F6700-DFC3CXL

Nov 13, 2012

I have one Cisco 7606 and i need to install a WS-X6748-GE-TX with WS-F6700-DFC3CXL.When I install the WS-X6748-GE-TX the module is powered off with the following warning:
 
00:01:45: %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 1, power not allowed: Unsupported baseboard/earl combination. [code]

View 1 Replies View Related

Cisco Switching/Routing :: X6748 And NAM-2 Modules Inaccessible After Installing Linecard

Oct 8, 2012

I've installed second WS-X6748-SFP linecard on my catalyst 6509 with sup720-3b and after that NAM-2 and IDSM-2 module become inaccessible from management network. I can only login with session slot N proc 1.When I execute #hw-module module 4 reset, modules become accessible.
 
#sh module from cat6509
 
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  2   48  CEF720 48 port 1000mb SFP              WS-X6748-SFP       SAL114670XW
  3   48  48-port 100FX SFP Ethernet Module      WS-X6148-FE-SFP    SAL1201BZKF
  4   48  CEF720 48 port 1000mb SFP              WS-X6748-SFP       SAL1625ETFJ
  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL1206FNGQ
  6    2  Supervisor Engine 720 (Hot)            WS-SUP720-3B       SAL1206FVFB
  8    8  Intrusion Detection System             WS-SVC-IDSM-2      SAD120502LR
  9    8  Network Analysis Module                WS-SVC-NAM-2       SAD120206LB
 
Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  2  001e.4a3e.3b30 to 001e.4a3e.3b5f   1.10  12.2(14r)S5  12.2(18)SXF1 Ok
  3  001e.4aea.e7b0 to 001e.4aea.e7df   3.3   8.4(1)       8.5(0.46)RFW Ok
  4  5057.a895.bb84 to 5057.a895.bbb3   2.4   12.2(18r)S1  12.2(18)SXF1 Ok
  5  001c.58d0.6dc4 to 001c.58d0.6dc7   5.6   8.5(2)       12.2(18)SXF1 Ok
  6  0016.c848.3698 to 0016.c848.369b   5.6   8.5(2)       12.2(18)SXF1 Ok
  8  001e.f7a1.54b0 to 001e.f7a1.54b7   6.3   7.2(1)       7.0(8)E4     Ok
  9  001e.f72a.ba62 to 001e.f72a.ba69   4.3   7.2(1)       5.1(2)       Ok
 
Mod  Sub-Module                  Model              Serial       Hw     Status
---- --------------------------- ------------------ ----------- ------- -------
  2  Centralized Forwarding Card WS-F6700-CFC       SAL114881B6  4.0    Ok
  4  Centralized Forwarding Card WS-F6700-CFC       SAL1624EGQS  4.1    Ok
  5  Policy Feature Card 3       WS-F6K-PFC3B       SAL1206FNZY  2.3    Ok
  5  MSFC3 Daughterboard         WS-SUP720          SAL1206FSFH  3.1    Ok
  6  Policy Feature Card 3       WS-F6K-PFC3B       SAL1206FP27  2.3    Ok
  6  MSFC3 Daughterboard         WS-SUP720          SAL1206FN26  3.1    Ok
  8  IDS 2 accelerator board     WS-SVC-IDSUPG      ADBG7270048  2.5    Ok
 
cat6500 running 12.2(18)SXF12a ios...

View 8 Replies View Related

Cisco Switching/Routing :: WS-X6748-GE-TX Change Module Cause Some Ports Of Server Offline

Dec 1, 2012

I have a server with 4 ethernet ports, 1G, they are bonded together, two of them was pluged into cat6500 module WS-X6724-TX. now we have moved the two ports to the replace module WS-X6748-GE-TX.
 
I have checked server side, the bond configuration are same no changed. what is possible reason replace module will cause link offline? why "sh run all" give the port is shutdown?

View 8 Replies View Related

Cisco Switching/Routing :: 6513-E / 6513 And WS-X6748-GE-TX Compatibility

Oct 29, 2012

we have a chassis 6513-E and a module WS-X6748-GE-TX, I'd like to know if could I put this module in any slot, since the documentation from Cisco says that any slot from a chassis 6500-E Series can support this module. And then in the documentation of WS-X6748-GE-TX says that this module is not compatible in the slots 1-8 of the 6513 chassis, only from 9th to 13th slots, in those slots from the 6513-E we already have 4x WS-X6748-GE-TX, and we'd like to know if could we put the module in the rest of the slots. The 6513, and 6513-E is kind of confusing.

View 4 Replies View Related

Cisco Switching/Routing :: Web Login Fail With 3750

Jul 28, 2012

I can access to Cisco 3750 with SSH, but fail to login to web http with the same login.I am able to get the login prompt, the login error I get is "The server at level_15_access requires a username and password."Below is my switch config:username admin privilege 15 secret 5 $1$xsdfajiwuoeirlkajsd.

View 1 Replies View Related

Cisco Switching/Routing :: 4900 HSRP For LAN Fail-over

Jan 23, 2012

Planning to implement HSRP in layer 3 switch.

We have two numbers of Cisco 4900 ME Switches. Basically want LAN failover from these devices. There are about 400 users in our network. I have attached rough network topology for your reference(I am not good at Microsoft Visio). Need to know implementation of the HSRP in these switches. Two distribution switches(Cisco 4900 ME Switches) are connected to 4 Access switches and these are connected to the LAN.

View 2 Replies View Related

Cisco Switching/Routing :: Dup Packet Fail With WS-C4506-E

Dec 20, 2011

What the message below means?  It's from our WS-C4506-E log running Version 03.01.01.SG.
 
Dec 20 16:27:26.182: (Suppressed 851 times)Dup Packet Fail for Sw PortDec 20 2011 16:27:28.068 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet4/22, changed state to upDec 20 2011 16:27:29.070 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4/22, changed state to upDec 20 2011 16:29:13.738 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4/22, changed state to downDec 20 2011 16:29:14.738 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet4/22, changed state to downDec 20 16:42:37.173: (Suppressed 162 times)Dup Packet Fail for Sw PortDec 20 2011 16:42:39.071 UTC: %LINK-3-[Code]....

View 2 Replies View Related

Cisco Switching/Routing :: 1841 Dual ISP Fail Over Using Track

Jan 9, 2012

we are trying to configure 1841 with dual Internet connection with failover using track.

View 4 Replies View Related

Cisco Switching/Routing :: C2969-48PST-L - PC Will Fail Authentication Intermittently

Jun 19, 2012

I have a c2969-48PST-L switch running IOS Version 12.2(55) SE. The switch is configured for 802.1x authentication. The radius server is a Cisco ACS 5.2. We are using PEAP and allowing EAP-TLS and EAP-MS-CHAPv2. Windows 7 PCs (HP Elitebooks) are using the "windows" supplicant and configured to 802.1x authentication is enabled using Microsoft Protected EAP (PEAP), we are not validating any certificates and the authentication method is Secured password (EAP-MSCHAP v2). What is occurring every so often is that the PC will fail authentication (intermittently) and the ACS shows the reason as being 5411 EAP session timeout. This is a pretty generic message according to TAC. The interesting part to me is the Authentication Method showing on the ACS when the authentication fails is simply PEAP. However, when it does not fail the Authenication Method is shown as PEAP (EAP-MSCHAPv2). We have the Cisco TAC looking at the ACS and they are saying the issue is the client not reponding to the request correctly from the switch.if the version of IOS softare on the switch maynot be handling the communication to the ACS correctly. I have wireshark traces of a successful authenication and unsuccessful one. There does seem to be any difference from the client side at all.

View 1 Replies View Related

Cisco Switching/Routing :: Router 2900 Fail After Power Outage

Apr 22, 2013

I recently copied a configuration from a router 2800 to a 2900. After a power outage no one can connect outside of the network through the new router. Before the outage all was fine. I put back the old router and all is fine which eliminates any cable or switch error. I have the router totally disconnect. I notice the configuration is in place.  My question is there any diagnostics that I can run to see if there is any hardware failure. It seems to boot up fine.

View 1 Replies View Related

Cisco Switching/Routing :: WS-C3750X-48T-S - Error On Default IOS / Authentication Fail

Feb 8, 2012

I am getting the below error on my new switch though I can’t find out A. why I am getting the error and obviously B. how to resolve said error as I need to ensure I am operating under the letter of the law and compliance.  The switch is a WS-C3750X-48T-S running C3750E-IPBASEK9-M, per my research IP base is the correct IOS for a T-S switch, the label on the outside of the switch matches the show ver (WS-C3750X-48T-S) so I know that IPBase is the right IOS for the hardware.  Could it be that I don’t have the license file installed? Below is what I get when I do a show license.  Lastly is there a place that I can find what IOS ships default with what switches, not version but type like c3750e-ipbasek9-mz.150-1.SE vs c3750e-ipbase-mz.150-1.SE
 
Error“%ILET-1-AUTHENTICATION_FAIL: This Switch may not have been manufactured by Cisco or with Cisco's authorization.  This product may contain software that was copied in violation of Cisco's license terms.  If your use of this product is the cause of a support issue, Cisco may deny operation of the product, support under your warranty or under a Cisco technical support program such as Smartnet.  Please contact Cisco's Technical Assistance Center for more information.”

[code].....

View 3 Replies View Related

Cisco Switching/Routing :: 7606 Sup720 With MSCF / Upgrade To 122-33.SRE6 Fail?

Mar 25, 2012

I faced with problem while i was attemping to upgrade CISCO7606 (R7000) from 12.2(33)SRE1 to 12.2(33)SRE6.
   
rommon 2 > boot c7600s72033-advipservices-mz.122-33.SRE6.bin
Loading image, please wait ...  
Invalid device specified
Booting from default device  
Initializing ATA monitor library...
string is bootdisk:c7600s72033-advipservices-mz.122-33.SRE1.bin

[code].....

View 3 Replies View Related

Cisco Switching/Routing :: 6500 - Power-Redundancy Mode Combined And Power Fail

Feb 28, 2011

I have a 6500 chassis with 2 power supplies. At the moment  I am using the default configuration:
 
power-redudancy mode redundant
 
The problem is that an inserted module is in "power deny" state due too insufficient power.
 
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
 
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
 
The 6500 config guide states:
 
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
 
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?

View 3 Replies View Related

Cisco WAN :: 2960 Should One Server Fail Other Will Act As Fail Over

Feb 22, 2012

We have two Cisco 2960 TT-L switches. I'd like to reduce single points of failure and have dual servers for most tasks. For example, two firewall servers and two web servers. Should one server fail the other will act as a failover.I'd like to extend the redundancy to the switches, and am thinking of connecting one web server to one switch, and one to the other. In the event a switch failed a set of servers would still run, and be able to talk to each other.I'd like to run two VLANs, one for the LAN, and one of the WAN, and connect the two VLANs on each of the switches with the associated VLAN on the other switch.

View 3 Replies View Related

Cisco WAN :: Output Drops On 7613 WS-X6748-GE-TX?

Jan 4, 2011

We have a 7613 w/ WS-SUP720-3BXL running 12.2(18)SXF11.  We have a 48 port WS-X6748-GE-TX that has one interface that keeps getting output drops for anything over 200Mb/sec.
 
See the attached file which has more details and show results. 

View 1 Replies View Related

Cisco WAN :: WS-SUP720-3BXL And WS-X6748-GE-TX Configuration

Feb 20, 2013

I have the above config in a 6509-E chassis with X2 Cac-3000 psu's
 
The problem i'm having is when everything is powered up it runs fine for about 10minutes then reloads the switch,The 6748 has a 6700-CFC installed the only way i have managed to get it run without crashes is to remove the 3BXL card from the sup and replace it with a PFC-3B, whilst this has solved the problem the client wants the 3BXL card to be installed, am I right in thinking that the CFC installed on the 6748 is incompatible with the 3BXL or maybe the 3BXL is faulty

View 4 Replies View Related

Cisco Firewall :: 5510 - Connections Routing Between Two Internal ASAs Fail

May 19, 2012

We have a site with two inbound circuits, one for internet and one for our MPLS.  Each circuit is being terminated by a 2921 Router and matching ASA 5510 Firewall.  For the internal network, the Internet ASA's inside interface (172.16.0.1) is the default gateway for all hosts.  OSPF is the routing protocol between all the routers and ASA's and routing is working.  In fact, ICMP is working as well.  From an inside host (172.16.0.81), we can ping anything on the MPLS network.  But when I try to use telnet (for example), the connection fails.  If I add a route to 10.10.10.0 to the host, or re-configure the host to point to the MPLS ASA (172.16.0.254) as it's default gateway, connections will establish.
  
Both ASAs are running 8.4(3), and have the following commands:
 
same-security-traffic permit intra-interface
interface Ethernet0/0
nameif outside

[Code]....

And from the MPLS nodes, I can see a tcp request is made. 

View 6 Replies View Related

Cisco WAN :: 891 Fail Over Configuration

Feb 2, 2012

Cisco 891 configuration Details: [code] I could connect to the Giga bite thernet wan, based on above configuration.When I test on FastEthernet8 for the secondary ISP connection it will not go through the internet.

View 17 Replies View Related

Cisco AAA/Identity/Nac :: Fail To Backup ACS 5.1?

Nov 27, 2011

I tried to backup ACS 5.1 but i found error messages as below
 
acs backup25Nov11 repository 25Nov11Repository
% Repository not found
% Error: Invalid repository name 25Nov11Respository

Please use a configured repository.

View 2 Replies View Related

Cisco :: Prime 1.2 NCS Fail Webpage

Feb 19, 2013

I have just started my installation of Prime 1.2. I have the OVA loaded (NCS-APL.1.2.1.12-K9) and I went through all of the setup. I have the webpage loaded but unable to get past the Root login. I then tried to change the password using the "ncs password root password password" command but get the error message "Execution failed: Cannot find user: root". I have seen some people talking about the wrong OVA file but that was for Version 1.1 I think.

View 1 Replies View Related

Cisco :: Prime Infrastructure CPI 1.3 Fail Over

May 6, 2013

we installed a new CPI 1.3. Both machines are in the same subnet and close to each other. Everything looks fine and is installed as we see in the config guide.When we halt the VM of the primary Server, the backup takes over but with errors. I'm also not able to login! [code] my colleauges did the same a few days ago also with problems or similar problems and restore the server from backup.

View 2 Replies View Related

Cisco :: LMS 3.2 Application Registration Fail

Mar 12, 2012

I am attempting to register QPM 4.1.5 into LMS 3.2.1 Portal, under Home Page Admin - Application Registration but It fails.It seems to be a bug where it puts the details in the wrong place when submitting the info.
 
This is the output that it tries to submit obviously - Description, host name, port number and protocol are mixed up.You have selected the following application to be imported from the remote server. [code]

I'm not sure where to find the Tomcat logs or how much use they would be.

View 1 Replies View Related

Cisco VPN :: ASA-5500 Fail Over Synchronization

Feb 28, 2013

My client has two ASA-5500 in failover (8.4.4.1).To create AnyConnectVPN, the package must be uploaded on both machines - uncomfortable, but it can be accepted. The REAL problem is that the profiles (.xml file) are not synchronized.When I make a change of any of the parameters, after failover switching I loos alle the change.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved