I have just started my installation of Prime 1.2. I have the OVA loaded (NCS-APL.1.2.1.12-K9) and I went through all of the setup. I have the webpage loaded but unable to get past the Root login. I then tried to change the password using the "ncs password root password password" command but get the error message "Execution failed: Cannot find user: root". I have seen some people talking about the wrong OVA file but that was for Version 1.1 I think.
we installed a new CPI 1.3. Both machines are in the same subnet and close to each other. Everything looks fine and is installed as we see in the config guide.When we halt the VM of the primary Server, the backup takes over but with errors. I'm also not able to login! [code] my colleauges did the same a few days ago also with problems or similar problems and restore the server from backup.
We have two Cisco 2960 TT-L switches. I'd like to reduce single points of failure and have dual servers for most tasks. For example, two firewall servers and two web servers. Should one server fail the other will act as a failover.I'd like to extend the redundancy to the switches, and am thinking of connecting one web server to one switch, and one to the other. In the event a switch failed a set of servers would still run, and be able to talk to each other.I'd like to run two VLANs, one for the LAN, and one of the WAN, and connect the two VLANs on each of the switches with the associated VLAN on the other switch.
I'm currently running CiscoWorks LMS 4.0.1 on Windows 2003 under VMware and just got upgrade licensing for Prime Infrastructure 1.2. I am assuming that I will need to upgrade the current server to Prime LMS 4.2 in order to ensure that data migration to Prime Infrastructure goes well. I am planning to follow Cisco's recommendation to run Prime LMS and Prime Infrastructure in parallel for a time and migrate individual functions.
My real question is about Syslog handling. All of the managed devices are currently sending Syslog data to LMS. As a last step in the migration, is it possible to change the IP address of the Prime Infrastructure server to replace the Prime LMS server so that the Prime Infrastructure server will just start getting all the Syslog data, or do I need to go change hundreds of managed devices to point to a new address?
What is the relation between: cisco NCScisco Prime LMSCisco Prime infrastructure.As i orderd a Cisco Prime infrastructure from a Cisco Partner and what i got is :
x2 cisco NCS appliances x1 DVD cisco prime infrastructure x1 DVD Cisco prime 4.2
This webpage is not available.Google Chrome could not load the webpage because realm108.c8.castle.wonderhill.com took too long to respond. The website may be down, or you may be experiencing issues with your Internet connection.Reload this webpage later.Check your Internet connection. Restart any router, modem, or other network devices you may be using.Add Google Chrome as a permitted program in your firewall's or antivirus software's settings. If it is already a permitted program, try deleting it from the list of permitted programs and adding it again.If you use a proxy server, check your proxy settings or contact your network administrator to make sure the proxy server is working. If you don't believe you should be using a proxy server, adjust your proxy settings: Go to the wrench menu >Options > Under the Hood > Change proxy settings... > LAN Settings and deselect the "Use a proxy server for your LAN" checkbox.
I play dragon of atlantis on facebook and I cant get into one realm I can get into any other realm but It is just realm 108 I can not get into. I went to the library to could get into the realm then I came home and still can not get into it. I have uninstalled chrome and reinstalled it and same problem. It also has same problem with fire fox and ie. I have ran ait virus, anti malware software and same problem I have also release and renewed IP address still no luck. This is the only page I can not get into.
I have a network with a 2003 windows server and around 60 XP computers. I also have 2 different gateways. I am trying to access a webpage "eparts.rmpparts.com". When I enter the address it comes up to the page that says "IE cannot display the webpage".I have treid and both gateways and same result. I am also not able to ping the address from the PC within my LAN.I then went to a different network "not within my LAN" and I am able to access the site without any problem. I have accessed it from my phone also without any problems.I have tried to get to this page from the server and also around 5 other computers within the LAN and the same problem each time.I have security settings very low and also the firewalls are off. I tried on a computer that is connected to my LAN with no luck. I then disconnected that same computer and connected it to a different modem not within the LAN and had no prob getting to the site with the same PC.So I know it must have something to do with my LAN but I have no idea what it could be. I have tried everything I can think of and same result each time.
I am having trouble accessing the webpage related to my university (www.uniandes.edu.co) while connected through my router (Belkin Wireless G router F5D7230-49). I was able to access it without problem for the last four years, but recently I can't access it. If I plug in the PC directly to the cable modem, I can access the site. I can also access the website through a proxy server[CODE]
I have AT&T high speed (6Mbps). most of the time it works great. but sometime, links that I visit often does not load. sometime it just loads "This webpage is not available". I have to click links many times or fresh to load the page. Ping google.com is about 35ms..are there any settings on my DSL modem or network router that I can set to fix this issue? my equipments:
I've just recently upgraded a Cisco 877 to 887W router.
I basically copied most of the config across to the router with no problem.
ppp chap hostname and password all ok. ATM and Dialer1 interface comes up.
The problem I'm having is when I open Internet Explorer up, default homepage is Google. Google loads up fine, type a search is fine but when you click on the link or type URL, for example BBC News or Sky Sports, it takes a long time to load or times out (Page cannot be displayed)
DNS servers configured on Cisco router are: 8.8.8.8 and Virgin's DNS servers.
NSLOOKUP in cmd prompt it returns IP add no problem. however in web browser it fails except for Google.
However, with the same config on a 877 everything works perfectly...
I run into a 1230 that would have a Web page completely different than the usual one. Instead of getting the normal User/pass menu and then the menu on the left side frame, you get this:
Cisco Systems Accessing Cisco AIR-AP1220-IOS-UPGRD "1200AP"
Web Console - Manage the ap through the web interface.
Telnet - to the router.
Show interfaces - display the status of the interfaces. Show diagnostic log - display the diagnostic log. Monitor the router - HTML access to the command line interface at level 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15 Extended Ping - Send extended ping commands.
Show tech-support - display information commonly needed by tech support.
Everything appears to work ok in that peage excepting the "Web Console" link which would probably go to the usual home page.Getting to it from the console, everything looks to be ok. You can configure the unit using the IOS and the unit apparently works fine. I have 12.2(13) JA3 running.I defaulted the unit, reloaded the image... I'm still getting that home page.
My laptop won't open a web page anymore what is wrong? My desktop still opens itwhat can I do to fix it ? When I try to go to the web page I just get a blank screen and that is allIt was working just fine until I installed Adobe pro X
i've had this internet problem that has been going on with a wireless laptop i've had since april. it only happens on this computer, and i've tried many solutions. occasionally, i will try and go to pages on google chrome and an error pops up that says "this webpage is not available." when i play games that are online, they get disconnected as well. i've added google chrome and my other browsers to the firewall list and i've also changed the DNS server. when i use the troubleshooter it says something like "router, or modem is not connected to the internet. i've even downloaded the "fix it" program and it detected no problems
My laptop now is using windows 7 operating system. When i want to use wifi it connected but cannot access the webpage. I am using wifi from my android device. Before this my laptop is working normally. I can access to the webpage like usual. But since three days ago it happen. what is going on with my laptop or my android device. But my android device can access to internet normally.
I have a notebook with Windows XP SP2 installed onto it. I am trying to access the web either using Google Chrome or Internet Explorer but no lack.I have tried almost everything such as:
1. Delete Cookies / Browsing History. 2. Reset Internet Explorer Settings. 3. Checked LAN settings. 4. Checked Proxy Settings. 5. Checked for Virus.
When I select to logon to the computer with Safe Mode then Internet works. In normal mode not... When I ping any website I get reply with 100% success.
I cant access microsoft webpage. I have fresh copy of win XP pro SP3, IE 8, and connected through an updated Vodafone ADSL modem through ethernet. Strange thing is, I can access bank, tv over internet, etc. except MICROSOFT webpages.
I have a 1240Ag. Earlier I loaded a startup config from a backup. The AP came back up - I can SSH into it, but when I try to access the web management page it says "IE cannot load the webpage".
Can open (url) in work computer but not at home - Message coming up at home that it will be closed for maintenance and that was last week and has since finished now as i can open site at work but not at home
I am getting the error message "internet explorer cannot display the webpage", my computer tells me i am connected to my wireless and that internet is available but it will not open any webpages, no matter which browser i try. I have disabled all firewalls and run diagnostics but it just tells me there is a problem with my router, despite the connection being perfect for other devices. My computer is relatively new and i'm sure its not a virus as i have run different anti-virus and malware softwares.
I am trying to configure a Linksys RV042 VPN router as a simple router. I want to connect it to one of the ports from a CiscoASA5505 router because I need to connect 4 additional PC's and the ASA is out of available ports.I am trying to connect it through an ethernet port from my laptop.At first I configured the TCP/IP settings as getting the IP and DNS's automatically and but I was able to enter the setup by entering the default IP address (192.168.1.1).After 10 minutes it got disconnected and could not connect again.I get Status: Limited or no connectivity.If I try to type the IP address manually (192.168.1.1) I can ping the router successfully but the setup webpage never opens.what I need to do in order to access the setup webpage when I connect the router directly to my laptop?
I cannot access one particular website - one that I regularly use. I have checked with other users - they can access the site.
This has been going on now for about 2-3 weeks and evertime I try to access the site I get the following message: "Internet Explorer cannot display the webpage"
My laptop says that it is connected to my home wireless home network but no web pages seem to load yet when I connect to my neighbours connection using the same machine it connects and the browser loads instantly? I have made sure that the detect proxy settings box is ticked, and tried to reset my router, could it be a problem with my router and not my laptop?
I'm trying to connect to 192.168.1.1 in order to set up a password. When I type it in, I receive a message, Internet Explorer Cannot Display Webpage. Why can I not connect?
I have a lap plug into a wired connection and it has stop working, i have ran the windows fix program which didn't work, i plugged a different lap top into the wire and that works fine!
Experienced the same sort of behaviour with an ACE 4710 version A3 (2.5). When trying to connect to a webpage on port 443, the pages over 1 minute to download fully. I have timed the download using the plug-in firefox. What is strange is that the browser successfully makes the connection, 200OK etc, but each 'get' takes a very long time to transfer. If I go directly to the server and don't pass via the ACE the page takes between .7 and 1 second to transfer.Is there a way to speed this transfer up, I am currently looking at connection maps.
Is there a way to configure a webpage where end users would go to change their passwords? I would not like to use the network devices themselves with the "change password at next logon" option.
I believe ACS 4.2 has such solution. Does 5.2 have it too?
Using QuickVPN from one RV220W to another RV220W I cannot access the Webpage of the remote router. Goes to "CERTIFICATE NOT VALID" then click through that, and the the login page will not come up. Sceen flashes a hint of blue background, then turns white, then just sits there saying "Waiting for response from ???.???.QuickVPN will sucessfully connect and I can use all computers behind the router. Just cannot access the Webpage of the remote router. I can access the Webpage of the local router.Also, when I hookup using QuickVPN from an "Internet Cafe" that is using a Netgear router. I can then access the webpage on both remote routers (of course, depending on whom I QuickVPN'd into at the time).
I have called Cisco on this with no luck. They said to update my JAVA. I am currently JRE 6 Release 30 and still no luck. The Log files reveal nothing and are darn near unreadable since there is no line breaks in the log file. Have to manually edit the log to pick stuff out.
