Cannot Access Setup Webpage From RV042
Nov 10, 2011
I am trying to configure a Linksys RV042 VPN router as a simple router. I want to connect it to one of the ports from a CiscoASA5505 router because I need to connect 4 additional PC's and the ASA is out of available ports.I am trying to connect it through an ethernet port from my laptop.At first I configured the TCP/IP settings as getting the IP and DNS's automatically and but I was able to enter the setup by entering the default IP address (192.168.1.1).After 10 minutes it got disconnected and could not connect again.I get Status: Limited or no connectivity.If I try to type the IP address manually (192.168.1.1) I can ping the router successfully but the setup webpage never opens.what I need to do in order to access the setup webpage when I connect the router directly to my laptop?
View 10 Replies
ADVERTISEMENT
Nov 24, 2009
I have a RV042 router and we are trying to set-up our OWA for outside access. I can't figure out which ports or which page those ports are on to open them. We are a small company and we do not have IT except for ourselves. The internal network works fine but i can't get the Exchange access from outside.
View 2 Replies
View Related
Jul 12, 2009
I am trying to setup a VPN using an RV042 (fw ver: 1.3.12.6) to access a VISTA computer over the internet using a laptop using QVPN's latest version. I finally got it to connect but then hang's with error " Gateway is not responding, do you want to wait?". If I say yes it go through the login again and hangs. If I say no, it hangsup. I've tried a couple different ideas using tunnelling and static IPs in the router but nothing. All I want is to be able to access one computer through the RV042 over the internet from any other computer using the QVPN.
View 6 Replies
View Related
Nov 19, 2011
I have 2 VLANs set up and I know they are set as default to not allow one to communicate to the other. Is there a way to set a rule to allow that? I'd like VLAN1 to be able to access VLAN2, but not the other way around.
View 1 Replies
View Related
Apr 20, 2012
Every time I try to connect to the admin page of my router, I get "The connection to the server was reset while the page was loading." This happens with FIrefox 11, and started when I upgraded to 8 or 9. A machine running FF 3.6 does not exhibit this problem; I get right in. What IE 9 says is "Internet Explorer cannot display the webpage" (after complaining about the expired certificate).
I ran Wireshark to see if I could learn anything, but all I could figure out was this: https handshake was OK. First TLS packet is received by router, which then immediately issues a reset and ends the connection. I don't know why.
have I got a screwed up configuration (or router)?
View 5 Replies
View Related
Oct 21, 2009
i've got a stack of 3750's configured, everything is working fine, but the web interface for the stack will only present the web based express configuration page. I can't get it to go away. what needs to be done to clear whatever flag or register that causes this behavior. the cli is fine, it's not trying to force epxress setup there, only in the web interface. will reloading the software image fix this?
View 16 Replies
View Related
Apr 6, 2010
I'm trying to setup a DVR camera system and two web page server boxes behind a Linksys WRT54GL. The problem I have is that all of the devices want to use port 80 to generate the web page. Individually, I can get the boxes to work, but when I try to put it all together everything seems to fall apart. I've got to the DVR set to External port 80, Internal Port 80 IP address 192.168.1.254. The web page server box I try to set to External port 8001, Internal port 80, IP address 192.168.1.200, when I try to save this setting I get the error message Internet IP address and LAN IP address are in the same subnet. If I change the web page server settings to External port 8001, Internal port 8001, IP address 192.168.1.200, it will save the settings, but it won't work that way because it won't actually generate a web page when I try to access that port.The error message doesn't seem to make since as all I'm changing is the port number, not the IP address or subnet mask.
View 9 Replies
View Related
Jan 19, 2011
I am having trouble accessing the webpage related to my university (www.uniandes.edu.co) while connected through my router (Belkin Wireless G router F5D7230-49). I was able to access it without problem for the last four years, but recently I can't access it. If I plug in the PC directly to the cable modem, I can access the site. I can also access the website through a proxy server[CODE]
View 9 Replies
View Related
Dec 13, 2011
I cant access microsoft webpage. I have fresh copy of win XP pro SP3, IE 8, and connected through an updated Vodafone ADSL modem through ethernet. Strange thing is, I can access bank, tv over internet, etc. except MICROSOFT webpages.
View 2 Replies
View Related
Jul 11, 2012
My laptop says that it is connected to my home wireless home network but no web pages seem to load yet when I connect to my neighbours connection using the same machine it connects and the browser loads instantly? I have made sure that the detect proxy settings box is ticked, and tried to reset my router, could it be a problem with my router and not my laptop?
View 1 Replies
View Related
Jan 20, 2012
I have a sony vaio VGN-NW20EF running windows 7, It use to work fine but now I can't access the internet wirelessly. It detects and connects to networks wirelessly and it even says I have internet access but the msg cannot display the webpage keeps coming.
It works fine with the ethernet cable. It works fine wirelessly if I use my mobile phone as a hotspot as it's a HTC HD 2 and works as a router on the go, through the phone's internet. I've restored the computer to the earliest date available and no luck.
View 1 Replies
View Related
Dec 19, 2011
Using QuickVPN from one RV220W to another RV220W I cannot access the Webpage of the remote router. Goes to "CERTIFICATE NOT VALID" then click through that, and the the login page will not come up. Sceen flashes a hint of blue background, then turns white, then just sits there saying "Waiting for response from ???.???.QuickVPN will sucessfully connect and I can use all computers behind the router. Just cannot access the Webpage of the remote router. I can access the Webpage of the local router.Also, when I hookup using QuickVPN from an "Internet Cafe" that is using a Netgear router. I can then access the webpage on both remote routers (of course, depending on whom I QuickVPN'd into at the time).
Location #1
Office #1
RV220W: RV220W-A-K9-NA SER: SER15140314Firmware: 1.0.3.5
IP: 192.168.63.1
Location #2
Office #2
RV220W: RV220W-A-K9-NA SER: SER151600R2
Firmware: 1.0.3.5
IP: 192.168.2.1
I have called Cisco on this with no luck. They said to update my JAVA. I am currently JRE 6 Release 30 and still no luck. The Log files reveal nothing and are darn near unreadable since there is no line breaks in the log file. Have to manually edit the log to pick stuff out.
View 1 Replies
View Related
Apr 29, 2011
I try to access my router web page with a correct address (192.168.1.1) but on my computer i have this message {Network Error (tcp_error)} but i can access this page from another computer through the network (WHY)
View 1 Replies
View Related
Jun 17, 2012
I trying to portforward on my WRT54G2 router but can't access webpage because I don't know the username or password. Is there any way to find out the password and username
View 1 Replies
View Related
Apr 18, 2013
WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. After all that I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port.
View 4 Replies
View Related
Mar 5, 2013
I'm having some difficulty getting into the settings web page on my e4200 router while the modem is running. I can access it soon as the modem is turned off. Additionally I downloaded the Android cisco express connect app for my tablet which does allow me to access the router while the modem is switched on.
View 5 Replies
View Related
Feb 28, 2013
I have a continuing problem with my WRT54G2 wireless router. I set up my network, changing the password for the router, and I change the SSID, as well as the encryption password. When I set it up, and after changing passwords etc. I always log off, go back and log on, and it works fine. Once I set up the network, over time, I'll notice a device will no longer connect via wireless. When that happens, I try to log on to the router, and can not connect to the router using either Firefox or IE. When I try, I get Internal Server Error, or just nothing. I can ping the router, and if I run an IPCONFIG at this point, the default gateway does show 192.168.1.1. Every time this starts to happen, I must do a hard reset of the router. Once I do this, I can connect, and log on using the default settings, and re-set everything. This is a HUGE pain, as it takes a lot of time, and happens way too often.
View 2 Replies
View Related
Jul 15, 2011
WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port. Also the support site has been down for over 13 hours for routine maintenance service.
View 2 Replies
View Related
May 19, 2012
We have 36 cctv cameras slowing down our oracle network pc's all in same subnet. I want to remove the dvr's of cctv to a separate network to improve performance. How to accomplish that with a Rv042 linksys router? Or is there any other better way around. 5 Users access the cctv cameras all the time.
View 2 Replies
View Related
Nov 2, 2011
How do you setup a Clint VPN on a RV042
View 1 Replies
View Related
Oct 24, 2011
I'm a bit new at this and I wanted to know if this is possible with the RV042 or if there's a better product to use. Our server is at located at location A and locations B and C telnet to the server via a VPN. We're looking at getting another ISP at each location as a backup and abandon older modem backups.
Would I setup a VPN tunnel between (A and B) and (A and C) for each ISP? Also I had a question on local IP addresses and if this would work
location A, ISP 1 -> location B, ISP1
local IP 192.168.1.1 remote IP 192.168.2.1
Public IP aa.aa.aa.aa Public IP bb.bb.bb.bb
[ code]....
View 2 Replies
View Related
Nov 17, 2011
I am trying to access the settings webapge so that I can delete computers from the scan list. When I select the settings link it attempts to open the page but then the lights on the adapter start to flash and it seems to lose the connection with it ....... The other links e.g. status, information and security seem to work OK provided they are aceessed before I select the settings link. One the lights have started to flash I have to switch off the adapter and switch back to restore the connection to the network. The adapter is connected to a BTHomehub. Other than this issue the printer works fine through the network.
View 15 Replies
View Related
Mar 16, 2011
We have a Network set up with a RV042 router. Router is hooked up to Cox Cable and ATT DSL. Currently have 20 computers hooked up to the router all using Static IP addresses. Setup has been in place for over 7 years. I want to set up a Wireless Access point on this network. The problem is, I can't seem to get DHCP to work right even WITHOUT the Wireless Access Point. I have taken one of the computers that works great with a static IP and changed it to be DHCP, I have enabled DHCP on the router and set the from and thru parameters for the IP assignment. The computer will connect and get an IP address and it allows me to see all the INTERNAL servers on the network but going to the Internet is REAL FLAKY. I usually have to refresh 5 or 6 times to get a web page and sometimes even that don't work. If I do get a page to come up there is about a 10% chance that it will bring up a subpage of that page without doing a refresh 5 or 6 times. Its like it won't hold the connection to the Internet. I did notice one thing different in the User Manual of the RV042 that is different than all the other Linksys routers I have worked with. It says that when you enable the DHCP on the router, you then make sure ALL computers hooked to it are set for DHCP. All other routers I have worked with do NOT use that word ALL. Am I missing some setting or is this a binding thing where you are either ALL static or ALL DHCP?
View 1 Replies
View Related
May 3, 2012
I have the rv042 vpn router which is the main gateway for our internet, connected to the vpn is one server for a software and then another computer is connected for a web server software, well i need to get these setup like so
Setup firewall rules that will block all inbound Internet access to the web server except port 443Setup firewall rules that will block all communication between the two internal networks, except ports 7000 and 1702These must be on two different internal networks
View 2 Replies
View Related
Apr 7, 2013
I am trying to setup the following. We have an RV042 Router and are using it as our gateway at the office. In the office we are using a Windows Domain abc.lan with DHCP of 10.0.0 - 10.0.0.254. The Router/Gateway is setup with a Static IP of 10.0.0.100.A couple of our office employees would like to work from home via VPN using their laptops. With the many options available for this router, I am not clear as to which options and what settings I should set.
View 2 Replies
View Related
Oct 13, 2012
I need DHCP Option 66 to be enabled my small business RV042 router, so the IP phones could know where is the TFTP server.
View 1 Replies
View Related
Apr 5, 2013
We are currently running Windows 2003 Domain in our network with DHCP turned on the Server. We have turned off the DHCP on the Router. We are using RV042 as out Gateway to the internet and everything is working fine. We would like to allow a couple of our users to be able to VPN into the network so that they can use Outlook and be able to access their files on the Shared Folder. The users would be using their laptops from their homes to connect via VPN using the standard Windows 7 VPN connection.
In the RV042 Interface there are many options and I am not sure I understand which setting would allow them to connect successfully to the network, be authenicated as a domain user.
View 1 Replies
View Related
Sep 1, 2011
I am trying to set up my rv042 to use the ddns service. The rv042 is directly connected to the ISP provided modem on WAN port 1. The problem is that instead of seeing the internet IP the rv042 is using the ISP sub net assigned IP.
LAN IP : 192.168.1.1 WAN1 IP : 192.168.12.9 WAN2 IP : 0.0.0.0 Mode : Gateway DNS (WAN1) :DNS (WAN2) : 192.168.12.1 DDNS(WAN1 | WAN2) : Off | Off DMZ Host : Disabled
View 1 Replies
View Related
Jul 24, 2011
I am trying to set up my router to grant http traffic a minimum bandwidth of - for example - 5,000 kBit (if there is any http traffic).
So I set http min. rate to 5,000 while I set nntp min. rate to 1 However, when I run nntp downloads on several connections (e.g. 10) my single http download never goes above 1,000 kBit. Without any other connections I reach 8,000 kBit.
I am using a single 12 MBit line.
View 4 Replies
View Related
Apr 6, 2013
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies
View Related
Jun 28, 2011
I had an older Linksys RV042 working perfectly until it blew up on me after 5 years of faithful service. This new 'Cisco' with v4.0.0.07-tm firmware appears to be a dramatic step backwards - I'm tempted to call it a heap of junk!!!
1. The 'Smart Link Backup' is not working (our primary ISP failed today and it did *not* switch over to the backup ISP on WAN2 as advertised and more critically ..
2. It *will not* allow me to access the sbs-2003 R2 server using Remote Web Workplace.
From ouside the office I can connect to the server using a Remote Desktop Connection and my laptop clients can use the built-in sbs 'VPN' connections but not RWW.
I have duplicated all the port forwarding as per the old router, turned off the firewall and even tried forwarding 'all traffice to the servers external NIC all to no avail. I get 'error 404' when clicking past the customary 'continue to this website ..." certificate warning.
I administer another 2 installations that use different routers and work flawlessly
View 1 Replies
View Related
Jan 12, 2011
I have been trying to resolve this issue with only allow facebook access throug the content filter between 12pm and 1 pm. However The settings never seem to take. Is this a bug in the system? If I start the filtering from 1300 to 1200 that should allow facebook to be accessible only on lunch.
View 2 Replies
View Related
Aug 19, 2011
I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 Replies
View Related
