Linksys Wireless Router :: WRT120N - Can't Access Config Webpage
Jul 15, 2011
WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port. Also the support site has been down for over 13 hours for routine maintenance service.
View 2 Replies
ADVERTISEMENT
Apr 18, 2013
WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. After all that I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port.
View 4 Replies
View Related
Jun 17, 2012
I trying to portforward on my WRT54G2 router but can't access webpage because I don't know the username or password. Is there any way to find out the password and username
View 1 Replies
View Related
Mar 5, 2013
I'm having some difficulty getting into the settings web page on my e4200 router while the modem is running. I can access it soon as the modem is turned off. Additionally I downloaded the Android cisco express connect app for my tablet which does allow me to access the router while the modem is switched on.
View 5 Replies
View Related
Feb 28, 2013
I have a continuing problem with my WRT54G2 wireless router. I set up my network, changing the password for the router, and I change the SSID, as well as the encryption password. When I set it up, and after changing passwords etc. I always log off, go back and log on, and it works fine. Once I set up the network, over time, I'll notice a device will no longer connect via wireless. When that happens, I try to log on to the router, and can not connect to the router using either Firefox or IE. When I try, I get Internal Server Error, or just nothing. I can ping the router, and if I run an IPCONFIG at this point, the default gateway does show 192.168.1.1. Every time this starts to happen, I must do a hard reset of the router. Once I do this, I can connect, and log on using the default settings, and re-set everything. This is a HUGE pain, as it takes a lot of time, and happens way too often.
View 2 Replies
View Related
Jan 31, 2012
I posted before about my problem in forwarding certain ports in a LAN-to-WAN cascaded router setup, and I finally gave up looking for a solution, and went for a LAN-to-LAN. On the internet there is many articles to be found on how to accomplish the setup, but none of them is complete, and as such, I think I really screwed up someplace. My setup: ISP modem/router (192.168.1.1 / 255.255.255.0) DHCP enabled, and DHCP address range 3-100 NAT configured Static IP address for a Synology NAS connected to the E4200 SSID id_1
Then the E4200 Internet connection type: I set to Static IP IP 192.168.1.2 Subnet mask 255.255.255.0 Default gateway: 0.0.0.0 (to disable the WAN)
Then, the network setup: Router IP: 192.168.1.2 gave me the error that WAN and LAN IPs were identical. I played around quite some time but always got an “illegal value” error. Then finally I put the IP to 192.168.0.1 (IP I had in LAN-to-WAN) and this was accepted. And subnet mask: 255.255.255.0 The SSID I left unchanged from what it was, id_2 (also gives me the advantage that I know to which router I am connected)
I rebooted the E4200, and I was connected. But … I am unable to connect to the E4200 configuration page, and even Cisco Connect cannot establish the connection.
View 9 Replies
View Related
Oct 3, 2011
I can't access the web based setup via 192.168.1.1. I've had this problem since I swapped to Static Ip from PPPoE. I changed internet provider and now when it type 192.168.1.1 in the browser it says Internet explorer can't show the web page. I've tried Crome and FireFox but with the same result. I followed the instructions in [URL] but to no result.
View 1 Replies
View Related
Jul 6, 2012
My Wireless-N Home Router WRT120N with version 1.0.07 seems to have a problem blocking Sites through scheduling with Access Restriction "Allow" ...I notice that... when I enable access restriction, with policy and some range of computers connecting to my router , and set it to "allow" from "monday - friday" from "8am-6pm" .. with a purpose of blocking some social networking sites, example facebook, It works perfectly fine. But when the "scheduled" time comes ( before 8am and after 6pm ).. I cannot access the internet.. router is working, it detects my modem.. but no internet connection. It always happen before and after the "scheduled time" before the configured access restriction takes over. I have to disable the Access Restriction to continue our internet access.
View 4 Replies
View Related
Nov 9, 2011
I have the CISCO Linksys Wireless Router Model Number: WRT120N. My laptop is finding the router, and connecting to it fine. However, when I try to log onto the internet, it says no internet connection (same in the available net work section in the menu bar).Internet (Charter) they have checked the modem and there is no issue. I have also plugged the Ethernet cord directly from the modem into the computer, and unable to access the internet.
View 6 Replies
View Related
Dec 5, 2012
I reset my router (WRT120N) and used a laptop with cable connection to reconfigure the router. With the laptop I can acces the router admin wireless, but with my home pc I am not able to acces the router! I get "The username or password you've entered is incorrect. Please check and try again." Like I said, wireless acces with laptop is no problem.Is this a security issue that allows only acces with computer that you configured the router?
View 4 Replies
View Related
Jan 7, 2011
how i can change WRT160Nv2 settings if i cannot find it with default 192.168.1.1;i'm using it as secondary router connected to FIOS actiontec primary, which has the 192.168.1.1; factory default reset linksys to that same IP, can't get it.cannot get internet without actiontec as its coax connected, and linksys doesn't have coax port.can'ty open configure page without internet connection, i believe.tried to use a neighbor's wireless but that's using 192.168.1.1 as well, can't log in to that.this started with firmware upgrade of linksys which left it invisible; didn't complete the upgrade, i don't think. but i've reset it and still nothing.
View 9 Replies
View Related
Jul 24, 2012
I decided to limit some Internet time for the kids going off this router (which has been working great since set up) but my Access Restrictions tab is missing. I have an identical router at my work place, same version/firmware, same settings, but the one at work does have the tab.
View 6 Replies
View Related
Jan 7, 2011
I have been using Mozilla Firefox for about 5 or 6 years now, and I have always been able to access any router setup through Firefox. Now though, I strangely can't. I try to log in from Firefox and I get stuck at the log in dialog box even if I use the correct password. If I cancel, the router assumes that I do not know the password and I get the standard Linksys access denied page. I then start using IE[current version], and I can log in absolutely fine. I can still use Firefox to browse the internet. I can ping the router. I can use Firefox to access the router setup from a different machine.
[code]....
View 9 Replies
View Related
Jun 5, 2012
I have a WRT120N I would like to convert from a router to a Wireless Access point. Can this be done and how would I do this?
View 4 Replies
View Related
Mar 4, 2013
i have router lynksys WRT120N and the latest 1.0.0.7 firmware. And the problem occured frequently. At about 13.00 i went out, wifi was working okay. At around 18.00 i returned home and i was trying to connect to the wifi with my android phone, and suprisingly it did not work. I tried on my laptop and on a android tablet. It did not work. The only thing that i could figure it out is to reset the router. I checked the settings, and there was no access policy e.g. time based access blocking.
View 5 Replies
View Related
Jan 27, 2012
I have configure pppoe on my WRT120N it say it's connected but cannot access wan side of the router.
View 1 Replies
View Related
Oct 29, 2011
All the documentation for this router shows the Access Restriction tab in the router configuration menu. It's the same as other linksys routers. The current version of the firmware doesn't have this functionality. Was it removed?
View 5 Replies
View Related
Aug 11, 2010
I have configure pppoe on my WRT120N it say it's connected but cannot access wan side of the router.
View 5 Replies
View Related
Jan 6, 2012
Have a PS3 that will connect to my wrt120n if I unplug the modem and router then plug back in after 2 minutes. if I shut off my PS3 or after approx 1 hour, PS3 drops my connection. I'm trying to access my router page online but after entering the default into my browser, the pop up box will not accept any combo of entries to allow me access. I have an SSID name and my router is password protected. It does not connect me when I use any combo of user name or password or the default "admin".
View 2 Replies
View Related
Dec 16, 2011
Before, I can access admin panel of router via 192.168.1.1 on any computer, be it wired or wireless.This time, I can't anymore.This time, I can only access admin panel on 1 computer only. The computer in which it's directly connected to the router, wired. All other computers, connected to a switch, which the switch is also connected to router, can no longer access admin panel.I can still open 192.168.1.1 with a username/password prompt but I can't log in. It's like it's always wrong password. Same with accessing from laptop (wireless).Before, I can access admin panel from any computer (wired), even from laptop (wireless). There are times that I have to restart router in order to fix my internet connection. Only this time, I have to access it from the computer that's directly connected to router (wired).How do I revert it back so that all computers will be able to connect to admin panel of router?I have just finished upgrading firmware from 1.0.05 to 1.0.06 but I still have the same problem.
View 5 Replies
View Related
Aug 24, 2012
I have NM 5.5.9195.0 and WRT120N Linksys router. I have an Ipod using WIFI to connect to the network which I would like to restrict times for. Using the access restriction page in the manage/setup of the router seems to not work well. The system does recognize the MAC address of the Ipod but setting times to allow or deny gives me odd results. The allow button actually denies use for one thing. Secondly, the deny time ends, but the Ipod still cannot connect sometimes. It is like the system gets stuck in deny. I have tested using a random 5 minute deny time period, yet the Ipod is denied all times. The system is consistent in denying the Ipod (actually using the allow button) but not on the times.
View 4 Replies
View Related
Sep 27, 2011
My WRT120N router doesn't have Internet Access Policy when I access it.
View 2 Replies
View Related
Oct 31, 2011
I have a problem with my Router WRT120N wen I connect to router with wireless are wired it`s not giving me Internet access but the light on the router of Internet is ON if I put the internet cable directed to my computer give me internet.
View 2 Replies
View Related
Oct 29, 2011
I have a WRT120N with Firmware 1.0.06..First peculiarity is that I can't access the web based admin screen from Firefox 7.0.1. The password prompt appears but won't proceed from there.Second, and main issue is that frequently (several times a day) I get a 'Limited Access' error on my wireless connection. On mouse roll over Windows 7 Pro gives the error message 'no internet access'. This problem appears to resolve itself after several minutes or straight away if the router is powercycled. During these 'Limited Access' moments I am unable to connect to the route web based admin page nor ping or tracert. [code]
View 8 Replies
View Related
Sep 21, 2011
I am currently using a Linksys E2500 router and cannot get a strong enough signal to an upstairs bedroom for my wife's iPad 2. I have a spare Linksys WRT120N that I would like to utilize to increase the signal upstairs. There is no way I can run a CAT 5 cable to that room. I believe both routers have WDS.
View 5 Replies
View Related
Jul 15, 2011
The old configuration was a Linksys/Cisco WRT120N plugged into a NETGEAR ProSafe VPN Firewall FV336GV2. I will list the settings below, but the short of it is that the WiFi router was in charge of getting the wireless clients but the Firewall was the one that assigned IP addresses and all that. This setup worked out just fine except that the WiFi router was in the basement and clients could only connect to it while still in the basement. They wanted to be able to connect to the network wirelessly while on the third floor, but couldn't even see the basement router from there. We shipped out an identical router configured beforehand exactly the same way, save for its MAC address and local IP address (those having premonitions, during troubleshooting I try setting different radio channels as well). The client plugged an Ethernet cable from the wall to port #2, and a desktop to port #3.
The desktop has internet access. Wirelessly, however, had issues The client only had a single laptop to test with, an XP SP3 machine. Unfortunately I couldn't pull specs from it as of this post, so I don't know if it connected by G or N. This laptop, which worked fine in the basement, wouldn't connect upstairs (it would sit trying to get an IP address forever) until I had him "forget" the basement network. At this point, he was able to connect to the upstairs router and access the internet. However, he could then no longer use the access point in the basement. I tried the same troubleshooting steps, like having him delete the wireless profiles from his network card and rebooting the router, but he couldn't even see the basement router while down there anymore.
Occasionally, it would show up for a moment, then disappear before he could connect to it. To make sure it was the basement router that was briefly appearing, I renamed the upstairs router to something else; this confirmed that indeed it was the basement router that was doing the "now you see me, now you don't" act. I then tried setting the basement router to Channel 1 while leaving the upstairs one at Channel 6. Still nothing, even though the laptop was about 25 feet away from the basement router and I had him wipe the wireless profile again. Rebooting the computer didn't solve the issue either. After this, I named the upstairs router back to the same as the downstairs one and had him go upstairs to test; he could connect to it right away.
I figure this is either a configuration issue on the laptop or routers (or firewall). Unfortunately, there weren't any other wireless clients to test with, and I'm not sure there will be when I continue troubleshooting on Monday. By the way, I looked for a "bridge mode" option on the WRT120N and couldn't find one; I'm told that the firmware doesn't support it. I don't feel comfortable putting on alternative firmware unless it's literally the only thing that will solve this. The configurations for the networking equipment are listed below.
NETGEAR ProSafe Firewall:
IP Address: 192.168.50.1
Subnet Mask: 255.255.255.0
DHCP Server: Enabled
Starting IP address: 192.168.50.50
[code]....
View 1 Replies
View Related
Feb 15, 2013
I am a powerbook G4 user, Mac's wireless is good so far.OSX 10.4.11 and when I am using E1000 extender, often the admin page shows up automatically like 192.168.1.1 and asks me to log in and once I log into the admin page, of corse show up the admin page.So, all my other internet pages are gone every time.Only shows the admin page.It does not happen with windows PCs.
View 1 Replies
View Related
Apr 20, 2012
Every time I try to connect to the admin page of my router, I get "The connection to the server was reset while the page was loading." This happens with FIrefox 11, and started when I upgraded to 8 or 9. A machine running FF 3.6 does not exhibit this problem; I get right in. What IE 9 says is "Internet Explorer cannot display the webpage" (after complaining about the expired certificate).
I ran Wireshark to see if I could learn anything, but all I could figure out was this: https handshake was OK. First TLS packet is received by router, which then immediately issues a reset and ends the connection. I don't know why.
have I got a screwed up configuration (or router)?
View 5 Replies
View Related
Jun 25, 2011
I have installed my E3200 downstream from the Verizon FiOS Actiontec (going the other way disables FiOS functions). 1. My browser can get to the E3200 (192.168.1.2) when connected via wireless, but not when connected via ethernet cable. 2. When going to connect wirelessly, the 2GHz connection is visible but the 5 GHz connection is not (I have them named differently). How do I see both wireless connections?
View 9 Replies
View Related
Mar 6, 2008
I own a wireless WRT54G, which has worked fine in the past. After setting up a new wireless network, I went to the router webpage to open some ports. The problem with the page loading is that it doesn't display correctly. No clickable text is displayed on the top of the page or the side bar, so I basically can't do anything whatsoever to configure it. I've tried loading it up in both Firefox and Internet Explorer, with IE saying the page loaded but with errors.
View 5 Replies
View Related
Aug 25, 2011
Downloading the latest firmware for the E3000. Seems like the link on the page is broken.
View 1 Replies
View Related
Jan 14, 2013
Region : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP : Virgin Media
Bought recently and I'm very pleased with Setup and Performance.
However, even though I have tried repeatedly with different user details and passwords I cant access the router Config without resetting to defaults using the pin in the back and admin admin.
I am using W7 and get to a log in screen via Control Panel / ... Network Sharing Centre / Network Map and see Router. Click on this and up comes a User Name and Pasword form but it never works with what I entered for the router.
View 5 Replies
View Related
Jun 26, 2011
How to time access restrictions with WRT120N router a wireless network?
View 7 Replies
View Related
