Linksys Wireless Router :: Wrt120n Unable To Access Settings Page
Jan 6, 2012
Have a PS3 that will connect to my wrt120n if I unplug the modem and router then plug back in after 2 minutes. if I shut off my PS3 or after approx 1 hour, PS3 drops my connection. I'm trying to access my router page online but after entering the default into my browser, the pop up box will not accept any combo of entries to allow me access. I have an SSID name and my router is password protected. It does not connect me when I use any combo of user name or password or the default "admin".
I entered some QoS settings and now when I load the QoS page I get this Javascript error message in Firefox.Error: missing ) after argument list Source File: [URL]. Line: 100, Column: 47 Source Code: QosList[0] = new QosEntry('0','3','0','Kathy's Mac','3', infor);
Basically, the Javascript chokes on any computer name that you enter that has an apostrophe in it. As a result, I don't have access to add or edit any settings on that page. Seems like a major rookie mistake, especially for a major network device manufacture.
I moved. Runnig an iMac at home. Can connect to the internet but was not able to access my cisco admin page for 54G V5. Also need to connect VPN but unable to.
I bought my self a WRT120N as my wireless router for my house. and not a long ago i bought the WAP4410N, for my repeater (after i ask to some people).my house were concrete wall, it have about 15-20cm thick, and we try to avoid any wired LAN. The destinaton were unreachable with only WRT120N.it's look like this (what i want for the network on my home) : [code] i already tried to setting the WAP4410 as a wireless WDS repeater, and wireless client/repeater (with and without "Allow wireless stations to associate"). both were unable to connect (limited), although i get the signal. for the IP on the WAP4410N (192.168.0.50), i used static IP [IP, Subnet and Default Gateway were fill in] within the WRT120N range (192.168.0.2 ->192.168.0.51)
- how i configure my WAP4410N as a repeater?
- is there any settings that i must set on the WRT120N, before combining the WAP4410N?
I just bought a new WRT120N router and it works perfectly on cable and Wi-Fi with one major issue on Wi-Fi. If i connect my phone or any phone for that matter that knows N speed the connection speed is 65Mbps and that is fine as all phones are limited to this speed over Wi-Fi. When I connect a Sony laptop that has N connection speed up to 300 Mpbs the connection speed shows as 65Mpbs. Are there any special settings I have to do to make the connection at least 100 or 120 Mpbs? What is the maximum connection speed of this model because I couldn't find any information about this. I did some digging on google and found that some people have connection speed of 120 Mpbs but they didn't give any advice on the settings they used or how they got to this speed. Keep in mid that I am refering to the connection speed now the actual download speed. So what settings I have to do to get at least 100 Mpbs speed connection?
LE: I would prefer a setting that would alow me to connect a Galaxy Nexus phone an iPhone 3G and the Sony laptop so that all of them will be connected at the maximum speed suported by that specific device.
I am having a problem accessing my router settings page. everything was working fine and then all of a sudden my desktop couldn't get internet but all the laptops could so I tried everything power cycling the everything changing the Ethernet cable and I got nothing. So then I hard reset my router and erased all the settings and now it works so I have internet just fine and right away after I hard reset I could access my router settings page and input all of my settings like DNS servers and port forwarding and changing my SSID etc. but now every time I try and go to it it just won't I don't even get the login prompt nothing. So why I can't access this page. Here is a copy of my ipconfig /all. Also when I ping 192.168.0.1 I have no packet loss.
Edit:I have gotten it to work in IE I have to go to HTTPS://192.168.0.1 and then click go to site anyways after it gives me a warning about the certificate being invalid and I have to allow it or whatever otherwise it won't bring up the login prompt. Also the same thing is happening for FF so I need to go to https://192.168.0.1 and click I understand the risks and add exception for it to work.
When I try to go to192.168.1.1 it says connection interrupted. If i use the Cisco Connect it tells me i am not connected to the internet. My pc is connected via ethernet cable. My son can pull it up on is laptop and is connect the our Linksys E3000 wirelessly. I can go online, I just cant get to the router.
I just got a WET54GS5 to use for game systems. i wa able to use the software in order to get the system online and working, but i am not able to access the wireless bridge though the web page. the username is blank and i put in the correct password, but it does not go through.
Firmware downloaded, FW_WRT120N_1.0.06.001_US after pressing APPLY nothing happens after few minutes it says. "There is an error in the Content-type field. Click the Back button to return to the previous page and re-enter the information."
We have Cable DSL modem that connects to router. One wired connection from router to PC. Wireless devices are 2 iphones 2 ipads and 2 imacs. Constantly having to power the WRT120N off and back on to regain connectivity.
I have a wrt120n wireless router and use Network Magic Essentials with 2 computers on my network. It has worked fine for about 2 years. I recently upgraded the desk top from an XP pro service pack 2 to a service pack 3. I am now unable to receive files from my laptop which is a Vista or print from the laptop. I can receive files on the laptop from the desktop. I am running McAfee and have spent about 3.5 hrs with a tech there but they have not been able to find any problems with their system.
I have a WRT120N that is connected to a cable broadband modem. I have my desktop computer connected via cable to the WRT120 and that works fine. However, I am not able to connect to the WRT120N with the iPhone. I get the message, :Unable to join the network "<network name>".I've searched on the boards, but cannot find anything specific to the WRT120N and iPhone.
For some reason my wireless router recognized my pc, or my modem, Neither is it able to connect to the internet. All the lights are on but not flashing/blinking like they used to. I tried to run the setup over and it couldn't find the router even though everything was plugged correctly. I tried reseting the router but that doesn't even affect it. All the lights remain on with on blinking or flashing no mater what I do. Is there anyway for my router to work normal again or do I need to get a ned wireless router?
I have a Linksys WRT120N which had suddenly and unexectedly stopped working after disconnecting my roku box. I didnt worry about it until I got an Iphone and now .I was able to re-establish the wireless connection on my netbook today after a ton of research and messing around with the settings and then downloaded network magic, which finally fixed the problem. I believe that it automatically transmitted the WEP key to the Netbook, which is what I am missing when I try to log into the network on the Iphone.How do I get this password to show up on Network Magic? When I look at the settings, it does not show the actual numbers, they are hidden.
I recently purchased a WRT120n router to set up wifi in my house. I had installed the software and had the Wifi up and running. However, I am unable to connect to my wifi connection thru my cell phones. It does not connect to any of the smart-phones we have at home (Nexus S, iPhone 3G, )
The wifi connection is working on the laptops (Mac and Windows). Just not connecting to the phones.
It's been a while since I sent into my router and messed with any of the Storage setting. I recently decided to change things around so I recently went in the router and attempted to access the Storage page but all I get is a blank page with this address http://192.168.1.1/storage/Disk_Management.asp.
I recently (~month ago) switched to a new computer after my old one (which I had configured the router on previously with no problems) died.Since then, I have been unable to access my router's config page (entering in the ip address simply results in a blank page with no prompt for username/password). Switching browsers (I've tried Firefox 5 and IE 8) does not solve the problem, nor does disabling AdBlockPlus/NoScript on Firefox. Any way to access my router so I can begin forwarding ports again?
I have the issue of being unable to access my router configuration page. My standard gateway IP (83.226.48.1), does not work, resulting in "unable to connect". If I try with my IPv4-adress, it just comes out with a blank page (Mozilla Firefox and Internet Explorer).
I'm having wrt610n and there is an issue, i can login to the config page via http, but using the same computer i'm not able to login there via https but the same time i can login via ipad and the other computer, using the https.i even tried to reset the router settings, but the result was the same, so what PC option can cause it?
I have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed." I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it.
I was doing some changes in baitone router due to mistake i have disabled something in it.Now i am not able to access its admin page....Before it i was accessing through 192.168.1.1
I can't access the web based setup via 192.168.1.1. I've had this problem since I swapped to Static Ip from PPPoE. I changed internet provider and now when it type 192.168.1.1 in the browser it says Internet explorer can't show the web page. I've tried Crome and FireFox but with the same result. I followed the instructions in [URL] but to no result.
My Wireless-N Home Router WRT120N with version 1.0.07 seems to have a problem blocking Sites through scheduling with Access Restriction "Allow" ...I notice that... when I enable access restriction, with policy and some range of computers connecting to my router , and set it to "allow" from "monday - friday" from "8am-6pm" .. with a purpose of blocking some social networking sites, example facebook, It works perfectly fine. But when the "scheduled" time comes ( before 8am and after 6pm ).. I cannot access the internet.. router is working, it detects my modem.. but no internet connection. It always happen before and after the "scheduled time" before the configured access restriction takes over. I have to disable the Access Restriction to continue our internet access.
I have the CISCO Linksys Wireless Router Model Number: WRT120N. My laptop is finding the router, and connecting to it fine. However, when I try to log onto the internet, it says no internet connection (same in the available net work section in the menu bar).Internet (Charter) they have checked the modem and there is no issue. I have also plugged the Ethernet cord directly from the modem into the computer, and unable to access the internet.
I reset my router (WRT120N) and used a laptop with cable connection to reconfigure the router. With the laptop I can acces the router admin wireless, but with my home pc I am not able to acces the router! I get "The username or password you've entered is incorrect. Please check and try again." Like I said, wireless acces with laptop is no problem.Is this a security issue that allows only acces with computer that you configured the router?
I decided to limit some Internet time for the kids going off this router (which has been working great since set up) but my Access Restrictions tab is missing. I have an identical router at my work place, same version/firmware, same settings, but the one at work does have the tab.
I have been using Mozilla Firefox for about 5 or 6 years now, and I have always been able to access any router setup through Firefox. Now though, I strangely can't. I try to log in from Firefox and I get stuck at the log in dialog box even if I use the correct password. If I cancel, the router assumes that I do not know the password and I get the standard Linksys access denied page. I then start using IE[current version], and I can log in absolutely fine. I can still use Firefox to browse the internet. I can ping the router. I can use Firefox to access the router setup from a different machine.
WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. After all that I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port.
i have router lynksys WRT120N and the latest 1.0.0.7 firmware. And the problem occured frequently. At about 13.00 i went out, wifi was working okay. At around 18.00 i returned home and i was trying to connect to the wifi with my android phone, and suprisingly it did not work. I tried on my laptop and on a android tablet. It did not work. The only thing that i could figure it out is to reset the router. I checked the settings, and there was no access policy e.g. time based access blocking.
WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port. Also the support site has been down for over 13 hours for routine maintenance service.
