We have Cable DSL modem that connects to router. One wired connection from router to PC. Wireless devices are 2 iphones 2 ipads and 2 imacs. Constantly having to power the WRT120N off and back on to regain connectivity.
View 2 Replies
I just installed an older router (WRT120N). Purchased an adapter for desktop and wireless connection for destktop works. Cannot get other devices to use the wifi (iphone, ipod, android phone...). I am at a loss. Saw some suggestions about disabling a Upn or something under the router's LAN properties
View 1 Replies View RelatedReciently I bought a WRT120N Router to get a better internet connection and to have more capacity to connect different wireless devices, because the modem from my internet provider company is extremely restrictive.
I use an iMac, a Notebook with Windows 7 and a Netbook with Ubuntu 11.04, besides different devices (iPhone, iPod, PS3, Kindle). Although when I configured the router I connected every devices simultaneasly, with better signal quality than before, after using it for a couple of days I found that it disconnects itself, I can't access internet, and my only solution it's to switch it off and on.
I have a WRT120N that is connected to a cable broadband modem. I have my desktop computer connected via cable to the WRT120 and that works fine. However, I am not able to connect to the WRT120N with the iPhone. I get the message, :Unable to join the network "<network name>".I've searched on the boards, but cannot find anything specific to the WRT120N and iPhone.
View 9 Replies View RelatedFor some reason my wireless router recognized my pc, or my modem, Neither is it able to connect to the internet. All the lights are on but not flashing/blinking like they used to. I tried to run the setup over and it couldn't find the router even though everything was plugged correctly. I tried reseting the router but that doesn't even affect it. All the lights remain on with on blinking or flashing no mater what I do. Is there anyway for my router to work normal again or do I need to get a ned wireless router?
View 15 Replies View RelatedI have a Linksys WRT120N which had suddenly and unexectedly stopped working after disconnecting my roku box. I didnt worry about it until I got an Iphone and now .I was able to re-establish the wireless connection on my netbook today after a ton of research and messing around with the settings and then downloaded network magic, which finally fixed the problem. I believe that it automatically transmitted the WEP key to the Netbook, which is what I am missing when I try to log into the network on the Iphone.How do I get this password to show up on Network Magic? When I look at the settings, it does not show the actual numbers, they are hidden.
View 6 Replies View RelatedI recently purchased a WRT120n router to set up wifi in my house. I had installed the software and had the Wifi up and running. However, I am unable to connect to my wifi connection thru my cell phones. It does not connect to any of the smart-phones we have at home (Nexus S, iPhone 3G, )
The wifi connection is working on the laptops (Mac and Windows). Just not connecting to the phones.
I have several devices connected to my EA4500 (two wired computers, two wireless laptops, iPhone, iPad, and a network drive). i have not been able to connect any new devices wirelessly. New laptops, PS3, friends laptops. Error message would suggest that password is being entered incorrectly, but I change the password to very basic word (idiot proof) but no luck.
View 9 Replies View RelatedI have a WRT610N which does not allow me to connect any new devices to the wireless network. This is a recent problem as I have been able to connect new devices before. Devices on the wireless network, those that have been on the network, are able to disconnect and reconnect. Just new devices are excluded. Have gone through the admin screens to see if something is amiss but can not find anything.
View 5 Replies View RelatedI have a WRT610 and am unable to connect any devices wirelessly. All the lights on the right hand side of the router are on except for the USB connection....what am I doing wrong? The router has worked for about a year flawlessly and last night all wireless connections quit.
View 9 Replies View RelatedI'm seeing some weird behavior trying to connect my Windows XP SP3 desktop via a USB wireless to my Windows network via Linksys WRT120N Router. It is unable to connect with DHCP. "Limited or No Connectivity" is shown on the network icon and no internet connectivity is present. When i manually assign a static IP, i am able to get connectivity to browse the internet, and I am able to ping the other computers in my network, but I am unable to view the windows workgroup. I am able to manually map network drives, but those drop continually. There seems to be no rhyme or reason to the connectivity and the dropping while I am using the static IP. DHCP does not work at all. I'm just trying to get this computer connected to the windows workgroup so that I can map network drives and printers once and for all. Right now the rest of the network (ethernet cabled to router) works fine. I'm thinking it may be something in the routers wireless config, as I am having the same issues (DHCP not working at all, static IP working but constantly dropping) with a Mac laptop.
View 3 Replies View RelatedI have a Cisco Linksys Router Model WRT120N - which is connect wirelessly to my MAC home computer. I also have a Dell D630 Laptop using WindowsXP. I have recently moved and my laptop used to connect to my wireless router (when I was at my old house) But now at my new house my laptop wont connect. It will connect wirelessly at other locations. The laptop picks up the wireless name and shows full strength.
View 1 Replies View RelatedI have a disconnecting problem with my WRT120N (Linksys) wireless router. Sometimes all wireless devices lose the connection to the internet, and the access to the router administration page (192.168.1.1) becomes impossible. In this case LEDs of power, internet and wireless are lighting without flashing. This problem usually occurs every 48 hour, and there was no way to make a reconnection except turning the router off by unplugging the power wire and plug it again…
I hope find a solution for this problem here
Other question: are there any problems in Firmware Version: v1.0.04
Note: currently I use Firmware Version: v1.0.01
I recently upgraded my Linksys wrt120n router firmware & had to reconfigure settings. Subsequently, some (but not all) of my apple devices are having intermittent wireless connection problems. Specifically, my ipad1 & ipad2 never lose their connection but a mac book pro (~ 2 years old), iPhone 3g, iPhone 4, older iPod touch & very old i book g4 all work for a period of time (usually 1/2 day) & then lose their connection. When I attempt to reconnect these devices I receive the following error..."unable to join the network xxxxxx....". I also have a Dell laptop (1 1/2 yrs old) that generally does not have the connection problem. Finally, when the devices do lose their network connection all I have to do to reconnect is go to the Linkys router setup webpage & click on save & the wireless connection works again (almost like this is just refreshing the connection for these specific apple devices). I was not having any problem prior to the firmware upgrade & from what I have read the older firmware version is no longer available so going back to the old firmware does not appear to be an option.
View 1 Replies View RelatedRouter 1: I have a WRT120N wireless router connected to the Internet. It has IP 192.168.1.1 and DHCP is enabled with address range 192.168.1.100 up.
Router 2: I have a WRT310N router connected to the LAN via LAN port to ethernet jack in the wall (not WAN/Internet port). It has ip 192.168.1.2 and DHCP is DISABLED.
All the devices on my network can see each other. Devices connecter to router 1 can see devices connected to router 2.The problem is, devices connected to router 2 cannot get to the Internet. I verified clients connecting to router 2 are assigned the same DNS addresses and the same gateway 192.168.1.1 as the clients connected to router 1. But for some reason router 2 doesn't know how to router Internet traffic out through router 1?
I tried plugging the LAN cable into the Internet/WAN port on Router 2 but then devices on Router 2 can no longer see devices on Router 1. I've seen discussions of setting up router 2 on its own subnet: 192.168.2.1 instead of 192.168.1.2 but then supposedly devices on router 2 will still not be able to see devices on router 1.
I'm guessing router 2 can't access the Internet because it is default configured to send Internet traffic to the Internet port, no t the LAN port. how to configure it so all devices on both routers see each other and router 2 devices can get to the Internet.
Firmware downloaded, FW_WRT120N_1.0.06.001_US after pressing APPLY nothing happens after few minutes it says. "There is an error in the Content-type field. Click the Back button to return to the previous page and re-enter the information."
View 2 Replies View RelatedI have a wrt120n wireless router and use Network Magic Essentials with 2 computers on my network. It has worked fine for about 2 years. I recently upgraded the desk top from an XP pro service pack 2 to a service pack 3. I am now unable to receive files from my laptop which is a Vista or print from the laptop. I can receive files on the laptop from the desktop. I am running McAfee and have spent about 3.5 hrs with a tech there but they have not been able to find any problems with their system.
View 3 Replies View RelatedHave a PS3 that will connect to my wrt120n if I unplug the modem and router then plug back in after 2 minutes. if I shut off my PS3 or after approx 1 hour, PS3 drops my connection. I'm trying to access my router page online but after entering the default into my browser, the pop up box will not accept any combo of entries to allow me access. I have an SSID name and my router is password protected. It does not connect me when I use any combo of user name or password or the default "admin".
View 2 Replies View RelatedI just bought a WRT120N to set up with my new Gateway Windows 7 64-bit using Cablevision cable internet. When I go through the steps from the CD to install, the wizard does not find the connection. When the internet is plugged directly into the computer, it works fine. If I have the router plugged in first and then run the install CD, it picks up the router as an existing router but I can't get it to install
View 4 Replies View RelatedI removed my ps3 from my network map and now i can't connect it back. How to do it?
View 1 Replies View RelatedI am trying to manually setup a WRT120N router. I am using my laptop (hard wired) for the initial setup. Okay, everything is working fine until I unplug the ethernet cable and try to go wireless. Will not connect to my network. I am also having this problem with all my other devices.
I had everything running fine on a WRT54G, I just wanted to try out the WRT102N. I did change the SSID name form what I was using on the WRT54G.
My mother in law bought my daughter a impression android tablet for Christmas it connects fine at public hotspots but I can not get it to connect to our wrt120n router at home. I have tried everything I know to add it. It asks for the password then says getting IP address then disconnects.
View 2 Replies View RelatedCOX cable was out yesterday doing some work outside our apartment building. Now, our CISCO LinkSYS WRT120N won't work. I was working before COX cable came out and has been working without problem for the past two years.When I plug the harddrive into slot 1 in the back of the router, "4" lights up. When I plut it into slot 4, "1" lights up. When I plug it into slot 2, "3" lights up, and when I plug it into slot 3, "2" lights up.I tried the router software, but when I reach the plug the router in step, the soft ware returns after a couple minutes and says it cannot locate the router, even though the router lights are on.
View 8 Replies View RelatedI can connect via a ethernet cable but can't connect via a "Ralink RT5390 802.11 b/g/n WiFi Adapter" on a HP Pavilion G6 Windows 7 OS. It finds the connection (with a strong signal) and asks for my network key but then says "Windows was unable to connect to network"
View 1 Replies View RelatedI just replaced my WRT54G with a WRT120N. Everything is working fine, but...
My MacBook Pro (about 18 months old) claims to support a/b/g/n, but it only wants to connect using 802.11g. It's running Snow Leopard. The laptop and the router are about 3 feet apart. Is there some incompatibilityin the version of 802.11n they support?
I can get regarding using the Collobos Fingerprint software through my WRT150N router. I'm using Windows XP SP3 and immediatly after installing (which went extreamy well) it immediatly found and listed all of my home network printers. All of the wired and wireless windows based systems in my house can see and print to the printers without any problem. However, getting ANY of my apple devices (iPad, iPhone etc ) to print will not even show them as listed on the device when I select print on the devices. Collobos says that I have to make sure that Ports UDP 5353 doe Bonjour and TCP 6361 for FingerPrint need to be open both ways for it to work, I have no problem getting into the router settings and have set them up as stated above in Port Range Triggering and enabled. Also made sure Filter Multicast was not check marked in Security. Unfortunatly, that doesn't seem to work as I had hoped.
View 3 Replies View RelatedI'm staying at a hotel where the internet offered is only wired. I can plug in the ethernet cable and no log-in is required. However, when I connect to the router and then try to access the internet from my laptop it does not appear to work.
View 2 Replies View RelatedI have the WRT120N. It seems to work for the computer and for Netflix through the BluRay, but I cannot connect my Kindle, my son's Kindle or either my ormy husband's phones anymore. They used to work.
Also, the free trial of Network Magic is over and it can no longer be purchased. Do I really need something like that?
I have a WRT160NV2 connected to Internet through cable and wanted to connect it wirelessly to a WRT120N that is far from it in order to expand its signal. Is it possible to do it wirelessly or the only solution is to connect them with cable?
View 1 Replies View RelatedMy router was working till date. Due to some reason, I disconnected the internet cable and connected it. After that it does not connect to internet.Based on the forum I accessed 192.168.1.1, it displays the administration page. I have reset to factory settings and switched off the router for a while and turned it
View 9 Replies View RelatedCan you use Cisco Connect Software with the Linksy WRT120N router? My blackberry curve also asks for a guest password and refers users to get the password from Cisco. I have Network Magic installed and it seems to work fine except for communicating with my blackberry.
View 3 Replies View RelatedI've recently bought a Cisco WRT120N router and, like my previous router, the NAT type on my PS3 console is type 3 which means I can't connect to my friends.Does any one know how to change this? I have not port forwarded or anything, as I'm not sure how and do not want to mess up the router's settings.want to change the NAT type to Open or Type 1.
View 2 Replies View RelatedI just switched to the EA4500 Router and I'm now unable to remotely access my camera devices. I have done the port forward. I can access the cameras from my local LAN both when using the local 10. ..and external 99 .. Addresses. When I go off the local connection - Access does not work. Slingbox did its auto configuration and I can access it. I just cant get to camera devices (Panosonic, Foscam, etc.).
View 3 Replies View Related
