My router was working till date. Due to some reason, I disconnected the internet cable and connected it. After that it does not connect to internet.Based on the forum I accessed 192.168.1.1, it displays the administration page. I have reset to factory settings and switched off the router for a while and turned it
View 9 RepliesCOX cable was out yesterday doing some work outside our apartment building. Now, our CISCO LinkSYS WRT120N won't work. I was working before COX cable came out and has been working without problem for the past two years.When I plug the harddrive into slot 1 in the back of the router, "4" lights up. When I plut it into slot 4, "1" lights up. When I plug it into slot 2, "3" lights up, and when I plug it into slot 3, "2" lights up.I tried the router software, but when I reach the plug the router in step, the soft ware returns after a couple minutes and says it cannot locate the router, even though the router lights are on.
View 8 Replies View RelatedI'm staying at a hotel where the internet offered is only wired. I can plug in the ethernet cable and no log-in is required. However, when I connect to the router and then try to access the internet from my laptop it does not appear to work.
View 2 Replies View RelatedFor some reason my wireless router recognized my pc, or my modem, Neither is it able to connect to the internet. All the lights are on but not flashing/blinking like they used to. I tried to run the setup over and it couldn't find the router even though everything was plugged correctly. I tried reseting the router but that doesn't even affect it. All the lights remain on with on blinking or flashing no mater what I do. Is there anyway for my router to work normal again or do I need to get a ned wireless router?
View 15 Replies View RelatedPutting this router back in service, I reset (10 and 30 sec hold) until lights flashed. Unplugged it. Came back and connected to computer. Used default u/n = blank and p/w = admin -- doesn't work, can't get to control screen. Tried various combinations and still won't work. How do I get router to respond?
View 9 Replies View RelatedReciently I bought a WRT120N Router to get a better internet connection and to have more capacity to connect different wireless devices, because the modem from my internet provider company is extremely restrictive.
I use an iMac, a Notebook with Windows 7 and a Netbook with Ubuntu 11.04, besides different devices (iPhone, iPod, PS3, Kindle). Although when I configured the router I connected every devices simultaneasly, with better signal quality than before, after using it for a couple of days I found that it disconnects itself, I can't access internet, and my only solution it's to switch it off and on.
I recently changed my internet connection to DSL from Cable, so now I'm using PPPoE type of connection.
Right now my router is configured as Automatic DHCP with the modem doing the PPPoE connection. All is fine and well.
Since I own a PS3, and Nat Type 3 conection is really bad for my online gaming, I would like to bridge my modem and connect to the internet through my router. That way I can properly forward my ports, use QoS and effectively get a better connection on the PS3.
I was able to successfully bridge the modem, but the PPPoE config on the router isn't able to connect to the internet.
Modem and router have been reinitialized after the configurations were changed. I do have the username and passwords, and they were properly put on the router.
My Linksys WRT120N router doesn't accept my cellphone's MAC address... Phone's MAC address is AC:81:F3:08:13:F5 but upon adding the MAC address Internet Access Priority Category based on MAC address, I get an error "Assign MAC address is incorrect".
View 1 Replies View RelatedI have a Motorola Docis Surfboard model Model SB6120 and can connect to the internet with the ethernet cable directly onto the labtop but if I connect it to the E4200 router the range is there but the internet connection is not. This happened 2 days ago and can't get the router to work.
View 4 Replies View RelatedI basically plugged it into my Verizon Fios router and downloaded the Cisco Connect application (since I have a macbook air which has no CD drive)
It sets up fine, I change my router name.... BUT at the end it says there is an issue of some sort. The Cisco Connect application reloads saying "repairing connection" but then does not repair it.
Not sure where to go from here. I also logged in to 192.168.1.1 but of course I do not know where to go from here. I also reset the router trying to start from new, but no dice.
Im trying to bridge my zyxel eq660r-f1 dsl modem so that i can resolve the nat issue im having in my home network. Only problem is that everytime I bridge the modem and hook my E4200 up, I cannot connect to the internet. If i connect my laptop directly to the modem, I do get internet but not through the router itself.
View 8 Replies View RelatedMy WRT54G2 v1 does not automatically connect to the internet on computer start-up. The computer will say "Connected, No Internet Access" In order to fix it I have to unplug the router and then plug it back in. This happens to any computer that tries to get online from a cold start-up. The router must always be unplugged, then plugged back in, then it will have internet access (and will generally maintain it throughout the session and even if the computer is restarted, i.e. warm boot). I have downloaded the latest firmware uprade.
View 9 Replies View RelatedI just bought a WRT120N to set up with my new Gateway Windows 7 64-bit using Cablevision cable internet. When I go through the steps from the CD to install, the wizard does not find the connection. When the internet is plugged directly into the computer, it works fine. If I have the router plugged in first and then run the install CD, it picks up the router as an existing router but I can't get it to install
View 4 Replies View RelatedI removed my ps3 from my network map and now i can't connect it back. How to do it?
View 1 Replies View RelatedI am trying to manually setup a WRT120N router. I am using my laptop (hard wired) for the initial setup. Okay, everything is working fine until I unplug the ethernet cable and try to go wireless. Will not connect to my network. I am also having this problem with all my other devices.
I had everything running fine on a WRT54G, I just wanted to try out the WRT102N. I did change the SSID name form what I was using on the WRT54G.
My mother in law bought my daughter a impression android tablet for Christmas it connects fine at public hotspots but I can not get it to connect to our wrt120n router at home. I have tried everything I know to add it. It asks for the password then says getting IP address then disconnects.
View 2 Replies View RelatedI can connect via a ethernet cable but can't connect via a "Ralink RT5390 802.11 b/g/n WiFi Adapter" on a HP Pavilion G6 Windows 7 OS. It finds the connection (with a strong signal) and asks for my network key but then says "Windows was unable to connect to network"
View 1 Replies View RelatedI just replaced my WRT54G with a WRT120N. Everything is working fine, but...
My MacBook Pro (about 18 months old) claims to support a/b/g/n, but it only wants to connect using 802.11g. It's running Snow Leopard. The laptop and the router are about 3 feet apart. Is there some incompatibilityin the version of 802.11n they support?
I've tried everything I can think of to try to connect to the internet with my Linksys WRT120N router.
The Problem
A few months ago my internet was out for a few hours, but I thought it was a router problem so I disconnected the router and connected my computer to the internet through my DSL modem. Of course, I couldn't connect to the internet because the internet was just out for a few hours on my provider's end. But after that the router wouldn't connect back to the internet.
Computer Specs
Windows Vista 32 bit. Intel Core2 DUO, 2.20 GHz, 2 GB RAM
Here are a list of things I've tried.
1. Installing it with the install disc.
2. Installing it manually
3. Updating the Firmware
4. Resetting the router multiple times
5. Making sure that Obtain IP Address Automatically is selected
6. Putting my MAC address into the router settings
7. Renewing my IP address
8. Flushing my DNS
9. Disabling both my Firewall and then making sure Windows Firewall was off
10. While doing all of this I rebooted my computer and powered down my DSL modem and router several times.
I have the WRT120N. It seems to work for the computer and for Netflix through the BluRay, but I cannot connect my Kindle, my son's Kindle or either my ormy husband's phones anymore. They used to work.
Also, the free trial of Network Magic is over and it can no longer be purchased. Do I really need something like that?
I have a WRT160NV2 connected to Internet through cable and wanted to connect it wirelessly to a WRT120N that is far from it in order to expand its signal. Is it possible to do it wirelessly or the only solution is to connect them with cable?
View 1 Replies View RelatedWe have Cable DSL modem that connects to router. One wired connection from router to PC. Wireless devices are 2 iphones 2 ipads and 2 imacs. Constantly having to power the WRT120N off and back on to regain connectivity.
View 2 Replies View RelatedCan you use Cisco Connect Software with the Linksy WRT120N router? My blackberry curve also asks for a guest password and refers users to get the password from Cisco. I have Network Magic installed and it seems to work fine except for communicating with my blackberry.
View 3 Replies View RelatedI have a WRT120N that is connected to a cable broadband modem. I have my desktop computer connected via cable to the WRT120 and that works fine. However, I am not able to connect to the WRT120N with the iPhone. I get the message, :Unable to join the network "<network name>".I've searched on the boards, but cannot find anything specific to the WRT120N and iPhone.
View 9 Replies View RelatedI've recently bought a Cisco WRT120N router and, like my previous router, the NAT type on my PS3 console is type 3 which means I can't connect to my friends.Does any one know how to change this? I have not port forwarded or anything, as I'm not sure how and do not want to mess up the router's settings.want to change the NAT type to Open or Type 1.
View 2 Replies View RelatedI have the CISCO Linksys Wireless Router Model Number: WRT120N. My laptop is finding the router, and connecting to it fine. However, when I try to log onto the internet, it says no internet connection (same in the available net work section in the menu bar).Internet (Charter) they have checked the modem and there is no issue. I have also plugged the Ethernet cord directly from the modem into the computer, and unable to access the internet.
View 6 Replies View RelatedFor home use, I have a Windows Vista PC which is hooked up to the Internet via a wireless EV/DO modem that plugs into a USB port. I just bought an iPad and for connectivity, I then bought a WRT120N wireless router. But I cannot attach the EV/DO modem to the WRT120N since the EV/DO only has a USB port. I plugged the PC into one of the 4 ports of the WRT120N and the iPad sees the router, but what I would like is that it also sees the internet when the PC is online via the EV/DO modem. Is there a way to configure this? I realize that the PC would always have to be switched on if I want to have the iPad online, but for the time being I am ok with that.
View 1 Replies View RelatedRecently I bought a new laptop (Sony Vaio SVE1511HFXW) and I haven't been able to connect it to the internet wirelessly. I previously was working on a Sony Vaio VGN-NR series laptop that I had no problem setting up a wireless connection for. I ran my router set up disc on the new machine and basically everything got ruined. My other laptop lost it's wireless connection and connecting it with an ethernet cable didn't work either. So now both computers were not connected. Actually, all devices can't pick up the wireless anyway (I tried to get on netflix with my Wii and it didn't work) I restarted the router several times, reset it once and nothing happened. I could only connect with the cable after I reset the modem and router, but it's still saying it "can't detect an internet connection." When I ping the router I get an answer back.
Here's what I get when I run ipconfig in the command prompt:
C:UsersShinsei>ipconfig
Windows IP Configuration
Wireless LAN adapter Wireless Network Connection:
[Code].....
Can a Linksys WRT120N Wireless N Router connect with an Acer 5253-BZ893 ?
View 1 Replies View RelatedI just installed an older router (WRT120N). Purchased an adapter for desktop and wireless connection for destktop works. Cannot get other devices to use the wifi (iphone, ipod, android phone...). I am at a loss. Saw some suggestions about disabling a Upn or something under the router's LAN properties
View 1 Replies View RelatedI have a Linksys WRT120N which had suddenly and unexectedly stopped working after disconnecting my roku box. I didnt worry about it until I got an Iphone and now .I was able to re-establish the wireless connection on my netbook today after a ton of research and messing around with the settings and then downloaded network magic, which finally fixed the problem. I believe that it automatically transmitted the WEP key to the Netbook, which is what I am missing when I try to log into the network on the Iphone.How do I get this password to show up on Network Magic? When I look at the settings, it does not show the actual numbers, they are hidden.
View 6 Replies View RelatedI recently purchased a WRT120n router to set up wifi in my house. I had installed the software and had the Wifi up and running. However, I am unable to connect to my wifi connection thru my cell phones. It does not connect to any of the smart-phones we have at home (Nexus S, iPhone 3G, )
The wifi connection is working on the laptops (Mac and Windows). Just not connecting to the phones.
i brought a new wrt120n from the retailer and when i tried to connect the modem and configure, my phone gets dead and i couldnt connect it to the internet.
View 1 Replies View Related