I have a Motorola Docis Surfboard model Model SB6120 and can connect to the internet with the ethernet cable directly onto the labtop but if I connect it to the E4200 router the range is there but the internet connection is not. This happened 2 days ago and can't get the router to work.
View 4 Replies
Im trying to bridge my zyxel eq660r-f1 dsl modem so that i can resolve the nat issue im having in my home network. Only problem is that everytime I bridge the modem and hook my E4200 up, I cannot connect to the internet. If i connect my laptop directly to the modem, I do get internet but not through the router itself.
View 8 Replies View RelatedI can't connect with putty to E4200.I tried different ways - telnet, ssh, etc.
View 1 Replies View RelatedI'm having a problem with Wake on Lan. (I'll bet you never guessed from the title, eh?). I have an E4200 and I can not get WoL to work over the internet.(I'm assuming it's not actually going out to the internet when I wirelessly wake it using shawn.dynamicservice.com and the subnet, but rather the DDNS name is being resolved through the ARP cache, but I don't know. I'm still learning) Consequently, if the sentence above in parenthesis is correct, I am unable to perform WoL from outside my LAN. What am I missing?
View 3 Replies View RelatedI basically plugged it into my Verizon Fios router and downloaded the Cisco Connect application (since I have a macbook air which has no CD drive)
It sets up fine, I change my router name.... BUT at the end it says there is an issue of some sort. The Cisco Connect application reloads saying "repairing connection" but then does not repair it.
Not sure where to go from here. I also logged in to 192.168.1.1 but of course I do not know where to go from here. I also reset the router trying to start from new, but no dice.
My router was working till date. Due to some reason, I disconnected the internet cable and connected it. After that it does not connect to internet.Based on the forum I accessed 192.168.1.1, it displays the administration page. I have reset to factory settings and switched off the router for a while and turned it
View 9 Replies View RelatedI have put two different e4200 routers in my network and both of them have the same issue. I believe there are some major firmware bugs with this router. First of all I set up everything using the web interface. My laptops could connect to the network and internet but any of my devices that use wireless bridges (WET610N) to connect could only get local network access. They could not connect to the internet. After some troubleshooting I found the reason it was not working properly. I used DHCP reservations in my network because of port forwarding and such. Well when the devices connected to the bridges were in the reservation list they were unable to connect to the internet. After I removed them they now are able to get on the internet without a problem. So that is the first problem I've found so far...
The second is I can no longer connect from my Xbox 360 to my Media Center PC. I tried to set up a new connection but this did not work either.
I purchased a new router and it doesn't have a security key. I can't connect my blue ray or roku.
View 1 Replies View RelatedI have a WAG320N working successfully on an ADSL line. I now have an E4200 that I want to link to it. I have it currently set up with the WAG320N using IP range 192.168.1.1 and the E4200 using 192.168.2.1.The E4200 is setup using the default - Automatic Configuration - DHCP and the internet port is connected to port 1 on the WAG320N. The E4200 links to the WAG320N successfully and picks up the correct external DNS addresses.I want to split the wireless network with the WAG320N providing the 2.4Ghz and the E4200 providing the 5Ghz.
View 6 Replies View RelatedOk this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7
Linkysy E4200 V1
Century link DSL modem 660 series
I have the 1.0.03 firmware installed and URL blocking doesn't work. I assigned the policy to the entire address range and could still access the web site I wanted to block.
View 1 Replies View RelatedMy WRT54G2 v1 does not automatically connect to the internet on computer start-up. The computer will say "Connected, No Internet Access" In order to fix it I have to unplug the router and then plug it back in. This happens to any computer that tries to get online from a cold start-up. The router must always be unplugged, then plugged back in, then it will have internet access (and will generally maintain it throughout the session and even if the computer is restarted, i.e. warm boot). I have downloaded the latest firmware uprade.
View 9 Replies View RelatedI've tried to cascade two Linksys routers, but It hasn't worked for me. The first one (which has cable-modem connection) is the brand new E4200, and the second one is the old WRT54GCv3.[code] However, the WRT54GCv3 doesn't get the IP address from the E4200's DHCP. I've also tried to connect them directly (without the PLC), even specifing an static IP on the second router, but I got the same results.I've to state I don't want to change the first router IP/gateway parameters because I have a web and game home server working with an static IP and I don't want to put it offline temporarily because of readjusting network parameters.
View 9 Replies View RelatedI have a E4200 v1, connected with a few PCs by ethernet ports and various devices by wifi. Now the wireless devices work perfectly but sometimes the PC via ethernet ports cannot connect to LAN and internet.
View 2 Replies View RelatedU just bought a new E4200 router to enjoy 5ghz band for the first time.I noticed the range at my house of the 5gh is smaller than 2.4 is that right?one of my pc is having trouble keep connected to the 5ghz signal or the router doenst respond to it, is there a way to improve that signal?
View 2 Replies View RelatedWe have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies View RelatedI am setting up a new E4200 modem, and have not been able to use the wired connection. The Windows 7 diagnositic on all three computers tells me "Local Area Connection, doesn't have a valid IP configuration."Model: E4200v1..I am using a new E4200 router, along with a new SE1500 5-port switch and a new SE2800 8-port switch.I am using a wired network that consists of two desktop computers, a laptop computer, a network printer, three Direct TV recorders, two Roku streaming video players, a BluRay player, and an XBox gaming console.Here is what I have done so far.
1- I can bypass the router to establish a direct wired connection to the cable modem. This works to access the internet. It establishes a new wired connection called Network 2.
2- I can access the internet using the wireless connection to the router. It shows a valid IPv4 address.
3- With all cables in place, all the lights are flashing on the router and on the computers.
4- I had changed cables and swapped cable ends.
5- Using the wireless connection, I can access the router home page (192.168.1.1). It shows valid IP addresses.
The problem is that my old Linksys BEFSR81 stopped working, with the same eror message for the LAN connection, "Local Area Connection, doesn't have a valid IP configuration."How often does the WAN port go bad? On both a five-year old BEFSR81, and a brand new E4200?
One of the many things that I liked about the e4200 over my olg 54GL was the fact that I could reboot it remotely. However, I've recently had a few problems that only a full power down would fix. In addition, I've noticed that the DCHP client table doesn't reset when I do a soft reboot. Is this intentional? Is the soft reboot not really a full reboot? Can it be made a real reboot?
View 7 Replies View RelatedI recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results. Other than a factory reset, get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago?
View 2 Replies View RelatedI have an E4200 with a USB hard drive connected to its USB port. I want to use the E4200 media server to stream divx and other video files on my Sharp Aquos HDTVs.I have an LC-70LE732U and a LC-52LE832U wired to my network. Both of them seem to discover and successfully connect to my media server however only MP3s and certain MPG files are detected. None of the AVI files show up.I have upgraded my E4200 firmware to 1.0.03 hoping that would fix the problem but it didn't. I don't want to run a Windows based media server as I don't have a computer that I can leave on all the time.
View 3 Replies View RelatedHow to connect the e4200 to a mac via afp? Trying to mount the network drive so the mac see it and can use for time machine backup.
View 3 Replies View RelatedI just connected my new E4200 router, it worked fine until it recommended updating, as soon as it connected to do this, the power light started blinking every second and it will no longer respond. Support has not facilitate.
View 9 Replies View RelatedI've had this router for just over a year now so the warranty is out and it just so happened to stop functioning last night. I'm fairly decent in the router world since I am studying for my CCNA, so I have tried just about anything imaginable. I woke up this morning with no connection, checked the modem, then the router. The router was powered on, but the up/downstream lights were not doing a thing. The modem is not the issue (I am hardwired as of now). I have tried both resets, including unplugging the device, and still can't get a response out of it. The logo light will turn straight on (no fad in and out like it's suppose to) and then it does absolutely nothing. I have never encountered this sort of problem on a home router before. I can't login to the router either.
View 5 Replies View RelatedI have 2 E4200's . One is connected to my ADSL Modem as DHCP and the other one is Bridged to the DHCP. I'm trying to connect to my E4200 that is set as Bridged. I am able to connect to my E4200 that is set as DHCP, but I cannot connect to the E4200 that is connected to that DHCP as Bridged.
How can I connect to that bridged E4200 because I want to upgrade the Firmware of the Bridged E4200?.
Been having problems connecting an old WGA54G v2 (firmware 1.16, March 29, 2005) to a new E4200 v2 (firmware 2.0.36) via WPA. I can get the two to connect using no encryption or WEP but not WPA. Using WEP is not an option for me,E4200 v2 wireless settings:
1. 5GHz broadcast is off, 2.4 GHz is on.
2. Network Mode - Mixed
3. Security Mode - WPA2/WPA Mixed Mode
4. Channel Width - Auto
5. Channel - Auto
6. Guest Access broadcast is off
WGA54G v2 settings:
1. SSID - same as router
2. Network type - Infrastructure
3. Security - enabled
4. Pre-shared key - same as router
5. Encryption - WPA Pre-shared Key, TKIP (tried AES, but still no connection)
Also, tried different WPA network modes on the router (Mixed, WPA personal, WPA2 personal etc.) to no avail. Switched between mixed, B and G network modes as well on e4200 v2 but still no connection. My guess now is that the WPA on the gaming adapter and the WPA on the router are just not compatible, as completely asinine as that sounds. Thought about updating firmware on the WGA54G v2 but checked in the download section here and the last firmware available is 1.13 (appears older than my 1.16, even though the 1.13 release date listed is a month after my 1.16).
I have this E4200 for about 3 months and allways has been used as an wireless router. Today i wanted to connect 2 wired computers to it via lan and whatever i do dosnt connect. Dosnt even let me acces the 192.168.1.1 page to router settings.I am on firmware 1.0.02, i also did a full reset and then did set up with cisco connect, did try that thing with the cisco usb connect and still no joy with the LAN conection.
One comp uses win 7 the other is on win xp. I can connect both comps succesfully to other router via the gigabit ports but not to this one.
On the 2.4ghz side, I'm set up on the cleanest channel (per inssider) which is 6, channel width is auto (although I've tried it fixed at 20 also), N-only, and security is WPA2 personal. WMM support is enabled. I'm running firmware 1.0.02 The laptops continually stay around 72mpbs, occasionally jumping to numbers in the 100 range... twice I saw it actually hit 144. Inssider shows the max rate as 144, while other N networks in range are as high as 270. I'm sitting right next to the router with 5 bars -- why is the max rate 144? Why won't it run at 300?
View 9 Replies View RelatedSo I purchased a Linksys E4200 a couple weeks ago from Best Buy (got the $149 price) and finally got around to setting it up last Thursday. Before I get to my problem, I am happy to say that I have not experienced the "blinking light" syndrome that seems to plauge a number of other owners. In fact, the E4200 is everything I hoped it would be ... except for one problem. I cannot get my sister's Acer Aspire One netbook to connect to it.
It's really strange actually; the netbook picks up the 2.4GHz SSID fine (it's set to mixed mode) and upon selecting it and I input the WPA2-Personal password no problem. Then, it takes forever to finally aquire a network address, like at least 3 full minutes (usually this process takes a few seconds). After that, it tells me it is connected to the network with excellent signal strength. Except, despite it saying it's connected, the Internet does not work at all. If I got into the details of the wireless adapter, it tells me that the router/network failed to give the adapter a network address.
[code]...
after setting up my e4200, I am no longer able to connect to Steam, I instantly get a connection error. I'm told it should work fine with UPNP, and I've even forwarded the proper ports just in case, but I cannot connect. I have latest firmware. Hoping someone else out there has same router and uses Steam.
View 6 Replies View Related1. I will be getting a e4200 on Thursday and was wondering if there is any advantage/disadvantage to using the Cisco Connect or just following instructions for manual setup using the web (I did it that way on my last router 6 years ago but was just following a script).?
2. Can I change things using the web after setting up using Cisco Connect or do I have to always use it:?
3. Finally after I set the router up can I just set up other computers in the house as I do now (just plug them in using wire or search for wireless and put in password)?
I've switched over from a d-link dir-655 router to the v1 4200. I've been playing around with the 4200 and trying to get it connected to my tv all night long. I have two laptops and two iphones connecting with no issues. I cannot for the life of me get the tv (GT30) to work. It picks up three signals, the 2.4 signal, the 5 signal and the guest signal. The only one that will even connect to the internet is the guest signal. When I run the connection test, however it will not connect to the vierra connect server. I've tried setting it up manually, and anything else that seems obvious. I had no issue with the dlink router at all.
View 1 Replies View RelatedRouter: E4200-V2
Firmware: 2.0.37
Just bought E4200-V2 and happy with the performance, except one thing.After several hours, I could not connect to the router manager both from "Cisco Connect" nor browser.I could resolve this by turn off the router and turn on again, but the same problem will be back after several hours.I tried to reset the router (reset 30 and reset 30/30/30) several times but have no luck.
I've noticed that my 192.168.1.1 login console was slow loading up on my E4200 V1. The router functioned just fine(wireless and wired). These past few days I tried to log in to set some DNS settings and I cannot access 192.168.1.1.I have tried via wireless and wired. The router powers on still seems to function but won't allow me to load up the admin console page.To my last resort, I held in the tiny reset button and the router seems to have went back to it's default settings (SSID = Cisco#####) but I cannot connect to it. what I can try to get back into the management window.I was able to manage everything from my laptop about a month ago or so, but now I can't do anything.
View 9 Replies View Related
