I have 2 E4200's . One is connected to my ADSL Modem as DHCP and the other one is Bridged to the DHCP. I'm trying to connect to my E4200 that is set as Bridged. I am able to connect to my E4200 that is set as DHCP, but I cannot connect to the E4200 that is connected to that DHCP as Bridged.
How can I connect to that bridged E4200 because I want to upgrade the Firmware of the Bridged E4200?.
I put the ea4500 on Bridged mode, and now I cant connect!I know I have to put the new ip address, and when I do I choose direct conect, it ask me for a password, I put the password, I click to connect, and then it just sits there in waiting....
View 9 Replies View Relatedhad a EA4200 about a year now, no probs, very stable, i'm thinking about getting a EA6500, for better coverage, iPhone apps, etc, would like to use my EA4200 in bridge mode from a EA6500, I'm a fairly new to networking etc, i'm assuming when the EA4200 is bridged, it will act like a repeater connected by cable, with same SSID ?
View 7 Replies View RelatedI'm trying to use my WAG120N router as a modem only/Bridged Mode and I've managed to enter all my settings needed on the WAG120N which is the Encapsulation to Bridged Mode Only, QoS to UBR, Type Of Connection to LLC, VPI and VCI to 0 and 35, DSL Modulation to Multi mode.On the EA4500's end I've entered my Usrname and password in the Internet settings and configured for PPPoE.
View 8 Replies View RelatedI have just recently replaced my Netgear router with an EA3500 and have it bridged t an Airport Express. From there I have an ethernet cable attached to an AV receiver (Pioneer 1021k), but all to often now with this new router to use any of the features of the receiver ie Airplay, iOS app remote, I must restart the router EVERY time. This is frustrating because the these issues were never present with the netgear router.
View 9 Replies View RelatedEA4500 in bridged mode and I can log in the the CCC account but nothing appears on the screen. I was able to see the settings, etc with the previious firmware. I reset the router and tried different browsers, PC, etc. Now running Ver.2.1.39.144146.
View 9 Replies View RelatedHow to connect the e4200 to a mac via afp? Trying to mount the network drive so the mac see it and can use for time machine backup.
View 3 Replies View RelatedI just connected my new E4200 router, it worked fine until it recommended updating, as soon as it connected to do this, the power light started blinking every second and it will no longer respond. Support has not facilitate.
View 9 Replies View RelatedI'm runing an ea3500 in bridged mode, classic configuration, firmware 1.0.30 build 126544. I got ftp working for my usb attached wv delements drive , but it is totally invisible in windows (except for ftp of course).I read in an older post that the usb drive in certain situations does not work (independent of disk manufacturer/type and such) and for certain configurations the ftp option might work but the windows mapped network drive doesn't , does that still apply? does it apply to bridged mode ?
View 1 Replies View RelatedI've set up PPPoE on my EA4500 router with a Vigor 120 modem in bridged mode and it says an internet connection is established, but the connection is extremely slow on all my devices. When I run the speed test within the EA4500 firmware it appears fine, but I cannot load any web pages on my laptop or other decives because the connection is so slow. The connection is slow with both wired and wireless connections. I've tried changing the MTU settings with no success. I've also tried using a different router and connecting the modem directly to my laptop and using PPPoE within the laptop and these both work fine, so I think it's clear there is a problem with the EA4500 router itself.
I'm just using the Vigor 120 to authenticate and connect to the internet itself, with the router in DHCP automatic configuration mode. I think this is causing a double NAT.
I've had this router for just over a year now so the warranty is out and it just so happened to stop functioning last night. I'm fairly decent in the router world since I am studying for my CCNA, so I have tried just about anything imaginable. I woke up this morning with no connection, checked the modem, then the router. The router was powered on, but the up/downstream lights were not doing a thing. The modem is not the issue (I am hardwired as of now). I have tried both resets, including unplugging the device, and still can't get a response out of it. The logo light will turn straight on (no fad in and out like it's suppose to) and then it does absolutely nothing. I have never encountered this sort of problem on a home router before. I can't login to the router either.
View 5 Replies View RelatedBeen having problems connecting an old WGA54G v2 (firmware 1.16, March 29, 2005) to a new E4200 v2 (firmware 2.0.36) via WPA. I can get the two to connect using no encryption or WEP but not WPA. Using WEP is not an option for me,E4200 v2 wireless settings:
1. 5GHz broadcast is off, 2.4 GHz is on.
2. Network Mode - Mixed
3. Security Mode - WPA2/WPA Mixed Mode
4. Channel Width - Auto
5. Channel - Auto
6. Guest Access broadcast is off
WGA54G v2 settings:
1. SSID - same as router
2. Network type - Infrastructure
3. Security - enabled
4. Pre-shared key - same as router
5. Encryption - WPA Pre-shared Key, TKIP (tried AES, but still no connection)
Also, tried different WPA network modes on the router (Mixed, WPA personal, WPA2 personal etc.) to no avail. Switched between mixed, B and G network modes as well on e4200 v2 but still no connection. My guess now is that the WPA on the gaming adapter and the WPA on the router are just not compatible, as completely asinine as that sounds. Thought about updating firmware on the WGA54G v2 but checked in the download section here and the last firmware available is 1.13 (appears older than my 1.16, even though the 1.13 release date listed is a month after my 1.16).
I have this E4200 for about 3 months and allways has been used as an wireless router. Today i wanted to connect 2 wired computers to it via lan and whatever i do dosnt connect. Dosnt even let me acces the 192.168.1.1 page to router settings.I am on firmware 1.0.02, i also did a full reset and then did set up with cisco connect, did try that thing with the cisco usb connect and still no joy with the LAN conection.
One comp uses win 7 the other is on win xp. I can connect both comps succesfully to other router via the gigabit ports but not to this one.
On the 2.4ghz side, I'm set up on the cleanest channel (per inssider) which is 6, channel width is auto (although I've tried it fixed at 20 also), N-only, and security is WPA2 personal. WMM support is enabled. I'm running firmware 1.0.02 The laptops continually stay around 72mpbs, occasionally jumping to numbers in the 100 range... twice I saw it actually hit 144. Inssider shows the max rate as 144, while other N networks in range are as high as 270. I'm sitting right next to the router with 5 bars -- why is the max rate 144? Why won't it run at 300?
View 9 Replies View RelatedSo I purchased a Linksys E4200 a couple weeks ago from Best Buy (got the $149 price) and finally got around to setting it up last Thursday. Before I get to my problem, I am happy to say that I have not experienced the "blinking light" syndrome that seems to plauge a number of other owners. In fact, the E4200 is everything I hoped it would be ... except for one problem. I cannot get my sister's Acer Aspire One netbook to connect to it.
It's really strange actually; the netbook picks up the 2.4GHz SSID fine (it's set to mixed mode) and upon selecting it and I input the WPA2-Personal password no problem. Then, it takes forever to finally aquire a network address, like at least 3 full minutes (usually this process takes a few seconds). After that, it tells me it is connected to the network with excellent signal strength. Except, despite it saying it's connected, the Internet does not work at all. If I got into the details of the wireless adapter, it tells me that the router/network failed to give the adapter a network address.
[code]...
after setting up my e4200, I am no longer able to connect to Steam, I instantly get a connection error. I'm told it should work fine with UPNP, and I've even forwarded the proper ports just in case, but I cannot connect. I have latest firmware. Hoping someone else out there has same router and uses Steam.
View 6 Replies View Related1. I will be getting a e4200 on Thursday and was wondering if there is any advantage/disadvantage to using the Cisco Connect or just following instructions for manual setup using the web (I did it that way on my last router 6 years ago but was just following a script).?
2. Can I change things using the web after setting up using Cisco Connect or do I have to always use it:?
3. Finally after I set the router up can I just set up other computers in the house as I do now (just plug them in using wire or search for wireless and put in password)?
I've switched over from a d-link dir-655 router to the v1 4200. I've been playing around with the 4200 and trying to get it connected to my tv all night long. I have two laptops and two iphones connecting with no issues. I cannot for the life of me get the tv (GT30) to work. It picks up three signals, the 2.4 signal, the 5 signal and the guest signal. The only one that will even connect to the internet is the guest signal. When I run the connection test, however it will not connect to the vierra connect server. I've tried setting it up manually, and anything else that seems obvious. I had no issue with the dlink router at all.
View 1 Replies View RelatedRouter: E4200-V2
Firmware: 2.0.37
Just bought E4200-V2 and happy with the performance, except one thing.After several hours, I could not connect to the router manager both from "Cisco Connect" nor browser.I could resolve this by turn off the router and turn on again, but the same problem will be back after several hours.I tried to reset the router (reset 30 and reset 30/30/30) several times but have no luck.
I've noticed that my 192.168.1.1 login console was slow loading up on my E4200 V1. The router functioned just fine(wireless and wired). These past few days I tried to log in to set some DNS settings and I cannot access 192.168.1.1.I have tried via wireless and wired. The router powers on still seems to function but won't allow me to load up the admin console page.To my last resort, I held in the tiny reset button and the router seems to have went back to it's default settings (SSID = Cisco#####) but I cannot connect to it. what I can try to get back into the management window.I was able to manage everything from my laptop about a month ago or so, but now I can't do anything.
View 9 Replies View RelatedI have set up my WAG320N with my E4200v1 successfully. The problem is that my laptops can't connect through WiFi with the E4200 router, but only with the WAG320N (wireless). Since it is the first time I set up a network alone I possible have made mistakes and that's why I can't connect to my router wirelessly. My desktop pc will successfully connect to both of my routers (wired)! My devices won't (DS,Laptops). I have WEP security in my WAG320N (because this is the only one my DS card can connect to) and in my E4200 I want to use WAP2 to connect my 2 laptops. I have made nothing more than setting them up and both of my evices are new.
It is for home use, both of my devices are updated to their latest firmware and the laptops won't identify the problem and will ask to restart the router. (I did many restarts both on my routers, PC, laptops)
I have an e4200v1 in bridge mode (LAN IP 192.168.1.2) connected via its WAN port to a LAN port on the primary router at 192.168.1.1.
Guest Wireless works perfectly in Ver. 1.0.04 build 11 but not in Ver. 1.0..05 Build 7.
I want to set up an E1200 as a wireless access point for guests, and ordinarily I'd be happy to connect it LAN-to-WAN and have it create its own subnet, but I need to connect one office PC to it also because connecting the E1200 to the main gateway displaces that office PC from the last Ethernet port on the main router.
So I disabled DHCP on the E1200 and connected it LAN-to-LAN. The modem is at a fixed, non-configurable address of 192.168.0.1/255.255.0.0 and the main router is at 10.0.0.1/255.255.255.0. I set the E1200 to a static IP of 10.0.0.12/255.255.255.0.The E1200's primary wireless connection works fine. The guest access connects, but it does not prompt for a password and web pages generate a "failed to load" sort of message.I temporarily connected the E1200 as the main router and re-enabled DHCP, though I kept the static IP of 10.0.0.12/255.255.255.0, and in this configuration the guest access worked. I observed that it connected via 192.168.33.1/guestaccess.cgi (or something very similar to that).
I got the new E4200 router as I had issues with my old router. I was able to DMZ my console with the old router. But with my new router my xbox IP has changed and I want to know which numbers to use and how to DMZ my Xbox with Cisco Connect.
View 7 Replies View RelatedAfter I updated my E4200 V1 with the 1.0.04 update I am unable to connect my WET610N to it with 802.11N. I can connect fine with 802.11G. I tried the Site Survey method of pairing them as well as manual. When it fails it goes through the minute timeout of trying and then Link Status is disconnected. I have anything from phones to laptops connect to the E4200 with wireless N, its just the WET610N that doesnt want to pair.
Before I was running the following:
E4200 V1 1.0.03
WET610N V1 1.0.05
Connection between them: Bridged, WPA2 Personal, 802.11N
After I was running:
E4200 V1 1.0.04
WET610N V1 1.0.05
Connection between them: Bridged, WPA2 Personal, 802.11G
E4200 does fail functionality on 2 area's:
- 1) Media Streaming Server
- 2) NAS supporting modern USB devices, which register with multiple personalities/devices in one physical USB device.
1) Is already known by Cisco and hopefully the choose to fix it properly
2) Must be known now. Multiple users are reporting this lack of support.
NAS functionality of E4200 does not work/ gives problems with:
- Toshiba StorE Alu 2S USB 3.0, 1 TB disk. PN: PA4239E-1HJ0
- Iomega eGo 1 TB USB 3.0, (black casing) , PN 31924500, RPHD-UG3
Both drives report themself with 2 devices under Windows 7: 1x USB storage decive + 1x CD readonly device?
I'm using E4200 with latest 1.0.02 firmware and found I can not connect to VPN with my iPhone4 by WiFi.Googled a bit and found it's a common problem for Cisco routers when wireless devices can not connect to VPN but wired ones connects with no problems.\
View 3 Replies View RelatedI have a Motorola Docis Surfboard model Model SB6120 and can connect to the internet with the ethernet cable directly onto the labtop but if I connect it to the E4200 router the range is there but the internet connection is not. This happened 2 days ago and can't get the router to work.
View 4 Replies View RelatedConnecting E4200 media server (external hard drive connected to USB in router) to PS3.mapped External HD to media server folder. and enabled UPnP Media Server. after trying all options I can't see media server in PS3.
View 6 Replies View RelatedI got E4200 with latest firmware (updated two days ago) and WD Studion with 2 Tb drive (it is HFS+ file system)Once I connect this drive to router I am not longer available to access 192.168.1.1.
View 5 Replies View RelatedI just got a new E4200 router and downloaded Cisco Connect from the web site...file name CiscoConnect.E4200.1.4.11160.2.exe. When I try to run it, I find through Task Manager that Setup.exe is using about 35 to 40% CPU, but I'm never even getting to anything on the screen, nor is Task Manager even showing it as a running application. I'm running Windows XP SP3 (latest updates). I tuned off the AVG virus scan. But it still just seems to hang. BTW, I used the web interface to fully configure the router and it works fine so I could get by without Cisco Connect, but it might just be easier to use.
View 4 Replies View RelatedIs there any way to connect a Seagate USB drive to the E4200.i have 2 USB portables and 1 USB with power cable, none of them seem to be recognized by the router
View 9 Replies View RelatedI can't connect with putty to E4200.I tried different ways - telnet, ssh, etc.
View 1 Replies View Related
