I have the 1.0.03 firmware installed and URL blocking doesn't work. I assigned the policy to the entire address range and could still access the web site I wanted to block.
View 1 RepliesI'm having a problem with Wake on Lan. (I'll bet you never guessed from the title, eh?). I have an E4200 and I can not get WoL to work over the internet.(I'm assuming it's not actually going out to the internet when I wirelessly wake it using shawn.dynamicservice.com and the subnet, but rather the DDNS name is being resolved through the ARP cache, but I don't know. I'm still learning) Consequently, if the sentence above in parenthesis is correct, I am unable to perform WoL from outside my LAN. What am I missing?
View 3 Replies View RelatedI have a E4200 v1, connected with a few PCs by ethernet ports and various devices by wifi. Now the wireless devices work perfectly but sometimes the PC via ethernet ports cannot connect to LAN and internet.
View 2 Replies View RelatedWe have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies View RelatedI cannot connect to my company’s VPN after installing the current firmware (FW_E4200_1.0.02.013_US_20110524) on my E4200 router. Version 1.0.01 was on the router when I received it, and it worked without issues. As soon as I upgraded version 02, I could not initialize a VPN connection. When I try to start a VPN session, I get a "page not found" error when attempting to initiate SSL VPN service using a Microsoft Forefront Unified Access Gateway. VPN pass through is enabled for all protocols in the e4200’s setup. As soon as I revert to firmware 01, everything works fine again.
I did a fresh download and re-flashed the 02 firmware just to make sure that it wasn’t an issue with a bad download or a faulty flash. The problem is consistent and repeatable. I have upgraded and downgraded twice, and the results are exactly the same. My VPN connection works with firmware 01, and it fails with version 02. There is a something different in the 02 firmware that is blocking VPN access.
Like others I see on this board, we've got middle- and high-school age kids whose access to FB and other sites needs to be controlled/scheduled.
I thought the DIR-655 was great, in that it has features that, on the face of it, would seem to be ideal for blocking domains and restricting access.
My problem: I've never been able to get this to work.
I've set up schedules and created lists of domains that I want to limit access to according to the schedules, but the only constraint I've ever gotten to stick is blocking access completely to the router.
*None* of the schedule-based or website-based access controls have ever worked; I'll put the block in place to my daughter's computer's MAC address so she shouldn't be able to get to youtube or facebook, save, bounce the router, but then I go by her room and she's still busily chatting away online to her FB friends.
Based on similar posts I've seen on this forum, this may not be a unique problem.
So in a nutshell, this is what I want to do:
1) Block certain computers (identifiable by MAC address)
2) from being able to get to particular named domains (and any of their sub-domains)
3) according to a schedule that I can create and modify.
My preference would be to do this in the router, but again, responses I've seen here suggest that may not be possible.
I am on a 200GB/month 100mbit cable plan with Telstra, and we have a number of sites/servers which we can download from which do not count towards our monthly download limit. Normally there would be 3-4GB of usage per day which was 'unmetered' but since upgrading to the E4200 router, everything that should be 'unmetered' is not being recognised and is being counted towards my monthly download limit - in other words, all traffic through the router is counted as chargable downloads.
Im not sure how it all works, but the E4200 router is definitely blocking something out... if i plug directly into the modem or use my previous router (WRT160N) everything works perfectly.
I just picked up the E4200 to replace a router, I can remote desktop into a computer that is physically connected to this router, but cannot remote desktop into other computers on the network that are connected via another switch.
View 1 Replies View RelatedI'm trying to build different content security scenarios for a potential deployment of ASA5500-X series firewall with CX module and ran into a trivial problem. A simple access policy has been configured to deny Skype. It's as simple as it sounds. To my surprise I don't see that it is being enforced.I have all my pending changes committed, events are now showing with hits, see attached print screens. Tried to start Skype on my PC with the source shown on the print screen it and don't see any effects of this policy.
As a side note, I know for sure that other type of filtering does work, i.e. I have configured a deny filter for gambling URL category and it seems to work nicely.
I purchased a new router and it doesn't have a security key. I can't connect my blue ray or roku.
View 1 Replies View RelatedI have a Motorola Docis Surfboard model Model SB6120 and can connect to the internet with the ethernet cable directly onto the labtop but if I connect it to the E4200 router the range is there but the internet connection is not. This happened 2 days ago and can't get the router to work.
View 4 Replies View RelatedI can't connect with putty to E4200.I tried different ways - telnet, ssh, etc.
View 1 Replies View RelatedOk this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7
Linkysy E4200 V1
Century link DSL modem 660 series
I've been into the setup page several times over the years but now it won't load. I recently reset it and want to setup security again.
View 6 Replies View RelatedIm trying to bridge my zyxel eq660r-f1 dsl modem so that i can resolve the nat issue im having in my home network. Only problem is that everytime I bridge the modem and hook my E4200 up, I cannot connect to the internet. If i connect my laptop directly to the modem, I do get internet but not through the router itself.
View 8 Replies View RelatedPutting this router back in service, I reset (10 and 30 sec hold) until lights flashed. Unplugged it. Came back and connected to computer. Used default u/n = blank and p/w = admin -- doesn't work, can't get to control screen. Tried various combinations and still won't work. How do I get router to respond?
View 9 Replies View RelatedI have a mac 10.7.4 and an xbox 360 slim. Whenever I try to play online like cod or fifa and someone else is on the computer It is super lagy, Laging. Before when I had a **bleep**y netgear 33 mb it worked perfectly fine. Now this router is has 300 +mb and it stil doesnt work. This router cost me $80 dollars. Before cisco linsys I bought a netgear not the **bleep**ty neatgear but a newer one and it still had the same problem.
View 1 Replies View RelatedI just received a new modem from my ISP acanac, the modem model is NetVito5300.When I connect the modem directly to my computer, I can access the internet, but if I connect through my wireless router, there's no wireless internet access. Wireless router model is CISCO Linksys E2000.I tried to download Cisco Connect Setup Software for PC and followed the step until one point it asked for my wireless username and password and I put them in correctly but it said my router was not successfully set up and failed. I should press the reset button and set the router to factory default mode, but I'm afraid I won't be able to set it up properly after doing so.What should I do to connect my new modem and wireless router properly so I have wireless internet access?
View 6 Replies View RelatedTrying to troubleshoot a Cisco Pix 501. We have a cable modem/router that goes to the Cisco box that then goes to my wife's computer. It's worked flawlessly since we hooked it up, even if we unplug/replug the router. Today, we unplugged the Cisco box itself to hook up a newer one. When the newer one didn't work, we tried to hook up the old one again to no avail. The led indicators seem to show that everything's working properly. We've unplugged and rebooted everything. Nothing works. The network monitor on the computer shows that it detects being connected to a network, but it always says no internet access.
View 1 Replies View RelatedI have a new Polycom Soundpoint IP550 VOIP phone that was not connecting via my old WRT54GS router. I purchased a new router, the E4200, thinking it was just the age of my original router. It also will not allow the VOIP traffic through. I can connect the VOIP phone directly to my CenturyLink modem and it works. But when I connect it back to the router it stops.
I contacted Cisco support and they had me upgrade the firmware to 1.0.02 build 13 May 24, 2011 version. Also adjusted down the MTU to 1364. That still did not work so they told me to take the router back to the store. I have not done that yet as I want to ensure that the router is really broken and not that I am missing a setting. The tech said that I should be able to plug the VOIP phone into the router and make NO additional changes.
I have a E4200 V1 router. A website that I have been accessing for years all the sudden no longer works. If I use my PC and PPTP VPN to another location, I can browse the website fine. If I remove the router and plug directly into my Comcast internet connection, I can browse the website fine. If I enable logging on the router, it shows the connection on port 80 just like every other outgoing connection. Security log shows nothing. I was on firmware version 1.0.03, upgraded to 1.0.05. Tried resetting to factory defaults before I updated firmware, and after I updated the firmware. The website all the sudden just stopped working 2 weeks ago. I also tried putting my PC as the DMZ IP address and nothing.
View 1 Replies View RelatedI've tried to cascade two Linksys routers, but It hasn't worked for me. The first one (which has cable-modem connection) is the brand new E4200, and the second one is the old WRT54GCv3.[code] However, the WRT54GCv3 doesn't get the IP address from the E4200's DHCP. I've also tried to connect them directly (without the PLC), even specifing an static IP on the second router, but I got the same results.I've to state I don't want to change the first router IP/gateway parameters because I have a web and game home server working with an static IP and I don't want to put it offline temporarily because of readjusting network parameters.
View 9 Replies View RelatedU just bought a new E4200 router to enjoy 5ghz band for the first time.I noticed the range at my house of the 5gh is smaller than 2.4 is that right?one of my pc is having trouble keep connected to the 5ghz signal or the router doenst respond to it, is there a way to improve that signal?
View 2 Replies View RelatedBuy new one Linksys E3200. Two day using and now have such problem. Every 30 minutes WiFi connection disappears for 10-15 sec. Then appear, but you can't connect to WiFi network for next 30 seconds. Update firmware of router to last version, but it doesn't work.
View 3 Replies View RelatedI have just upgraded my E3200 to firmware: 1.0.04 build 1 Apr 10, 2012.The guest network SSID didn't show before in my access point list, but now I can't even change the settings on the router.The options are greyed out.
View 6 Replies View RelatedI just purchased a new E4200 router. When I try to set it up, , it says that my software (Lion v. 10.7.2) is unsupported. Is there a download that will allow me to use this router?
View 2 Replies View RelatedI set up my new E4200 to forward port 7300 to a computer on my LAN. I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work. I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.
View 9 Replies View RelatedI have an HP LJ4050 plugged right into one of the open LAN ports on my E4200 with a CAT6 cable. Can this router work as a LAN print server? I can't pull up the IP on a browser window or ping it successfully.The 4050 doesn't have USB capability and I don't want to use the parallel port on my PC unless I have to.If possible, I'd like to have wireless computers on the network be able to print to it as well.
View 5 Replies View Relatedwhy Windows Backup in Windows 7 pro 64 would not backup over the network to a drive I have connected to the 4200s USB port? Everytime I run it I get a Access Denied error at the end, even though data has been transfered. After about 5 hours of searching both here and Microsoft's website, I just get lots of people with the same issue that hasnt been resolved anywhere consistantly.
View 1 Replies View RelatedI'm looking to purchase the E4200 and use an external HDD with enclose as a NAS (probably just a backup drive), specifically this model. [code]The HDD would be a 1TB Samsung Spinpoint F3.Does this router allow for USB 3 connections or at least fallback to USB 2? The first comment on the external enclose says so otherwise.
View 3 Replies View RelatedModel name: Linksys E4200
Model number: E4200
Firmware version: 2.0.36.126507
Operating system: Windows XP SP 3
Software version: 1.4.12005.2
Connection type (WAN): DHCP
My Canon MX882 multifunction printer is connected to the router via USB cable. The printer works. The scanner does not work.
I have tried both old firmware (2.37) then the Cloud firmware and now back to 2.37 again. the parental controls seems kind of fool proof but anyhow they dont work for me.If I set the internet access as denied at certain times, if the client is already connected when that time occours, it can continue to use internet (until it disconnects and tries to reconnect). Happens almost every time. And the biggest problem is that if I try to block internet access for a device like a cell phone, even though the user can not access the internet through the web browser, apps like Facebook, games etc can still access internet. Kind of useless parental control?!But I have tried to reset, reflash etc.Also I find this router pretty unstable, the only device that works flawless is my iPad (3), the laptops and cell phones at home loses internet connection every one and then, even though it seems like they have good connection to the router. Never been a problem with my earlier routers.
View 9 Replies View RelatedI am setting up a new E4200 modem, and have not been able to use the wired connection. The Windows 7 diagnositic on all three computers tells me "Local Area Connection, doesn't have a valid IP configuration."Model: E4200v1..I am using a new E4200 router, along with a new SE1500 5-port switch and a new SE2800 8-port switch.I am using a wired network that consists of two desktop computers, a laptop computer, a network printer, three Direct TV recorders, two Roku streaming video players, a BluRay player, and an XBox gaming console.Here is what I have done so far.
1- I can bypass the router to establish a direct wired connection to the cable modem. This works to access the internet. It establishes a new wired connection called Network 2.
2- I can access the internet using the wireless connection to the router. It shows a valid IPv4 address.
3- With all cables in place, all the lights are flashing on the router and on the computers.
4- I had changed cables and swapped cable ends.
5- Using the wireless connection, I can access the router home page (192.168.1.1). It shows valid IP addresses.
The problem is that my old Linksys BEFSR81 stopped working, with the same eror message for the LAN connection, "Local Area Connection, doesn't have a valid IP configuration."How often does the WAN port go bad? On both a five-year old BEFSR81, and a brand new E4200?