Linksys Wireless Router :: E4200 Firmware 1.0.02 Blocking VPN Access?
Aug 6, 2011
I cannot connect to my company’s VPN after installing the current firmware (FW_E4200_1.0.02.013_US_20110524) on my E4200 router. Version 1.0.01 was on the router when I received it, and it worked without issues. As soon as I upgraded version 02, I could not initialize a VPN connection. When I try to start a VPN session, I get a "page not found" error when attempting to initiate SSL VPN service using a Microsoft Forefront Unified Access Gateway. VPN pass through is enabled for all protocols in the e4200’s setup. As soon as I revert to firmware 01, everything works fine again.
I did a fresh download and re-flashed the 02 firmware just to make sure that it wasn’t an issue with a bad download or a faulty flash. The problem is consistent and repeatable. I have upgraded and downgraded twice, and the results are exactly the same. My VPN connection works with firmware 01, and it fails with version 02. There is a something different in the 02 firmware that is blocking VPN access.
View 9 Replies
ADVERTISEMENT
Oct 17, 2011
I have the 1.0.03 firmware installed and URL blocking doesn't work. I assigned the policy to the entire address range and could still access the web site I wanted to block.
View 1 Replies
View Related
Jul 2, 2011
I am on a 200GB/month 100mbit cable plan with Telstra, and we have a number of sites/servers which we can download from which do not count towards our monthly download limit. Normally there would be 3-4GB of usage per day which was 'unmetered' but since upgrading to the E4200 router, everything that should be 'unmetered' is not being recognised and is being counted towards my monthly download limit - in other words, all traffic through the router is counted as chargable downloads.
Im not sure how it all works, but the E4200 router is definitely blocking something out... if i plug directly into the modem or use my previous router (WRT160N) everything works perfectly.
View 7 Replies
View Related
Mar 7, 2012
I just picked up the E4200 to replace a router, I can remote desktop into a computer that is physically connected to this router, but cannot remote desktop into other computers on the network that are connected via another switch.
View 1 Replies
View Related
Apr 14, 2012
There is a new firmware for the E4200 router and I have no clue how to get the file. I've been searching in the support section » download tab without success. Any link to the new firmware how to get it?
View 1 Replies
View Related
Jul 28, 2011
I was looking for alternative firmwares until Linksys fixes their broken device.What do you guys make of this Tomato firmware? Do you think it has usb drive and Media Streaming (Twonky) support?
View 2 Replies
View Related
Oct 18, 2012
The file uploads fine, but I get an error message saying the router can't be updated atthe moment. I want to do the update because as of now, the router can't see my drive connected on usb (one ntfs partition and another one called wbfs, maybe that one is causing the issue about the drive).
View 2 Replies
View Related
Jul 2, 2012
I currently have Model name: Linksys E4200 Firmware version: 1.0.04 build 11 Software version: 1.4.12100.0
I'm trying to upgrade to the second and most up to date version. (Version: 2.0) firmware. Any links or way to do this? I tried doing it through my router settings under administration -> firmware upgrade but it won't update automatically. I have to find the actual update file and update the firmware through that.
View 2 Replies
View Related
Dec 13, 2012
Nom du modèle : Linksys E4200Numéro de modèle : E4200Numéro de série : 01C10C17152754Version du microcode (firmware) : 1.0.03 build 14OS : Windows 8Version du logiciel : 1.4.12284.0Type de connexion (réseau étendu) : DHCPAdresse IP (réseau local) : 192.168.0.1Adresse IP (réseau étendu) : 192.168.1.101Adresse IP de l'ordinateur : 192.168.0.135
I downloaded this file :[URL]I upgraded it, I typed 192, etc. in firefox, when to the maintenance tab, put the dowloaded file in "new firmware location" and clicked "update". It said: "you put a wrong file".this is written in the same tab : Current Firmware Version 6.0.0 Build 100906 Rel.43560
View 1 Replies
View Related
Oct 2, 2011
I am waiting for half year. And I read the forum know the NAT though put perfromance of 1.0.01 is poor than that of 1.0.03 of E4200.Actually a bit disappoint to CISCO LINKSYS products. It is not value to cost high selling price with poor functions and performance.
View 4 Replies
View Related
Aug 1, 2011
link to the original v1.0.0 firmware for the E4200. That was the best firmware for me and sadly I can't find a link to go back. v1.0.0 really had no problems for me. I initially skipped v1.0.1 becuase it disabled IPv6 which is a feature I want. v1.0.2 broke my YouTube and Netflix streaming. So I went back to v1.0.1 and my Netflix and YouTubue steaming returned to normal but I lost IPv6.
Any solution to Netflix and YouTube streaming problem on v1.0.2 when IPv6 is configured. (I'm positive the video is streaming over IPv4, but the IPv6 connectivity is available.)
View 9 Replies
View Related
Dec 30, 2011
I had a e4200,and i used 5ghz wireless.i can't set it to channel 149 or other high channel,my old wireless ethernet card can only support that.make the next version of the firmware can setting 5ghz channel to channel 149、153、157、161.
View 2 Replies
View Related
Dec 24, 2012
I've tried to upgrade/downgrade process twice with the same result. After few days without any issue 2.1.39.145204 gets stuck (=routing to internet doesn't work although I can ping from wireless network to all LAN IPs) and I need to reboot the router.
I have about 7 devices. Guest network is disabled, parental control is disabled, USB is not used, DHCP service is used, WPA2 mixed personal mode is used, MAC filtering is disabled, DMZ is disabled, DDNS is disabled, port triggering is not used. All the rest of settings are in default values.
As far as I notied the previous version 2.1.39.144146 doesn't get stuck at all.
View 1 Replies
View Related
Dec 18, 2011
I am unable to connect both of my smart phones to the access point. I am using WPA2 encryption on the AP. I can connect my phones to other AP's using WPA2. I have other devices that connect to the AP except my Android phones. I would like to be able to get some debug logs except the web interface says that the logging fictions are disabled when in bridge mode. Cisco/Linksys tech support: Any troubleshooting tips other than resetting the access point and or reflashing it.
View 4 Replies
View Related
Mar 10, 2012
I've assigned an ip address to my htpc using dhcp reservation. On my old router I could use the client name, for instance: ssh name@clientName Instead of: ssh name@ipAddress Currently I cannot do this with the stock cisco firmware (unless I'm mistaken). Is there something I have to do to get it working? Or do I have to resort to tomatoUSB/WRT.
View 1 Replies
View Related
Aug 24, 2011
I just bought a Cisco E4200 (from someone on Ebay, so returning is probably not an option). I was in the process of setting it up when it wanted to do a Router Update. Unfortunately, it did not specifically say to not do it WIRELESS. We had a disconnection in the upgrade process. Now the Power light just blinks. I can ping it from a hard-wired PC, but cannot get to the Administration Web page to retry the firmware update (I did download it from the site). Also Cisco Connect cannot connect to the router.
Oh Yes, I have tried holding reset button for 30 seconds, unplugging for 30 seconds, and replugging in the router. I do not get any different results.
View 6 Replies
View Related
Dec 1, 2011
After an indeterminate period my E4200 (firmware version 1.0.03) stops renewing the Internet IP address. This happens in both router mode and bridge mode.In router mode the E4200 is set for DHCP and connected to the cable modem, in bridge mode it is connected to a Dell switch with DHCP being provided by my Win2008R2 server.It appears that the device stops recognizing the existence of the Internet port - no lights come on when a cable is plugged in - whether connected to the cable modem or my Dell switch. Plugging the same cable into one of the 4 lan ports and that port lights up immediately (i.e. it is not a patch cable problem).If the E4200 is left switched off for some time (possibly days) it will work properly again for a while.
View 6 Replies
View Related
Apr 27, 2012
The device has been trying for days to auto-download and all it does is fail constantly. Saying that my connection is slow - gee, I have FiOS, I know it's not slow,maybe it's your Servers Cisco?Well, where can I obtain the direct DL link to that firmware file instead of relying on an unreliable device to get it and apply for me?
View 4 Replies
View Related
Oct 6, 2011
It is the router Cisco Linksys E4200.
My situation before I bought the router:
- my Internet speed is 120/20 (Mbps download / Mbps upload)
- speed test with my ISP gives 125/20 for 99% of the tests- speed test with [URL] gives 125/20 for 99% of the tests
- I never have had a router; my PC is connected directly to the cable modem
- My ISP is Vidéotron from Quebec in Canada : [URL]
My new situation with the new router :
- last Tuesday, I bought the router Cisco Linksys E4200
- the installation went fine and Internet works well
- during the installation process, the firmware is upgraded to 1.0.03
- speed test with my ISP gives 100/20 for 99% of the tests
- speed test with [URL] gives 100/20 for 99% of the tests
My observations :
- according to router status port, Internet port is 1 Gbps
- according to router status port, port 1 (where my PC is connected) is 1 Gbps
- it seems that speed cannot get more than 100/20 with the new router
- when I disconnect the router and I reconnect my PC directly to the modem cable, I still get 125/20
Calling Cisco support :
- Many tests are done during 3 chat sessions
- The speed is still 100/20
- The recommendation is to replace the router with a new one
Friend support :
- A friend of mine brought his router which is the same as mine- The speed is still 100/20 with his router
New router :
- As recommended by Cisco support, I got the router replaced from the store.
- I installed the new router
- During the installation process, the firmware is not upgraded; the firmware is 1.0.01
- The speed is now 125/20
- I upgraded the firmware to 1.0.03
- The speed is now 120/20
- I downgraded the firmware to 1.0.01
- The speed is now 125/20
Conclusion :
- My speed is maximized at 100/20 with the firmware 1.0.03
- I will stay with firmware 1.0.01 until firmware1.0.03 is corrected.
View 8 Replies
View Related
Dec 27, 2012
I have an E4200 router with 3 WET610N access points. I did the firmware update on the E4200 router about 2 weeks ago so my son could use his xbox when he got home after 4 months of being away. Everything seemed to work OK as far as I could tell....but when he went to sign into xbox live and watch Netflix, it will load to 98% and stop. A friend of his came over with the new Slim xbox 360 with built in wireless and it will connect fine on its own, if we hook up one of the 610N's to it, it will load to 98% on Netflix and stop again with error code R8152. Both of my older xbox's will hook up and play on xbox live, just not work with Netflix.
I also noticed, it shows the WET610N as a hard wire on xbox and will not search for any wireless networks, I have 2. The newer Slim xbox360 will search out both networks on its own if you allow it to use its internal wireless. This only happened since the firmware update. And this equipment was working fine before this. Is there a way I can restore the previous version of firmware?
View 4 Replies
View Related
Apr 1, 2013
This firmware bad, because my sync program, can't set create date of files on external usb storage connected to router, on 1.0.04 - all good.
View 5 Replies
View Related
Dec 9, 2011
I have a new E4200 with the latest firmware and my slingbox seems to not be playing nice with the router. It refuses to take the IP I reserved for the SB, but always defaults to 192.168.2.254. I use a 2 subnet just in case you're wondering. I have tried multiple reboots and the IP does not change. I have tried turning off UPNP, figuring that was hijacking the dhcp server, but that hasn't changed anything. I also notice that a few of my connected devices do not show up in the dhcp list, yet they connect and work ok.
View 2 Replies
View Related
Feb 6, 2012
Okay so I have been using my E4200 router and WET610N bridges for a while now without any issues really until yesterday when I updated the firmware on the 4200 now none of my WET610N's (I have 2) can connect via wireless at all. At first I thought it was a a wireless issue but I have other devices that connect up just fine via wireless.I've made no changes to the router or the bridges before the firmware update.
If I hook the bridge directly to the router I can access it and configure it, but looking at the "Status" page, I see the bridge try and connect wirelessly but is quickly disconnected. Range isn't an issue as in my testing the bridge was 2 feet from the router.I've update the bridges to the latest firmware and have verified a 100 times that the settings on both my router and the bridges are set correctly (when the bridges are hooked up via network card).
View 1 Replies
View Related
Oct 18, 2012
automatic firmware upgrade my E4200 can no longer be accessed.
View 6 Replies
View Related
Apr 19, 2013
I have a E4200 V1 router. A website that I have been accessing for years all the sudden no longer works. If I use my PC and PPTP VPN to another location, I can browse the website fine. If I remove the router and plug directly into my Comcast internet connection, I can browse the website fine. If I enable logging on the router, it shows the connection on port 80 just like every other outgoing connection. Security log shows nothing. I was on firmware version 1.0.03, upgraded to 1.0.05. Tried resetting to factory defaults before I updated firmware, and after I updated the firmware. The website all the sudden just stopped working 2 weeks ago. I also tried putting my PC as the DMZ IP address and nothing.
View 1 Replies
View Related
Jan 2, 2012
Video streaming was fine until I upgraded the firmware. Is it possible to downgrade the firmware?
View 3 Replies
View Related
Nov 6, 2012
I've been using my WRT310Nv2 Cisco wireless Gigabit N router for 2 weeks now, and sometimes, it's blocking access to Facebook.comI am not aware if it does the same thing with other websites, but my guess is that if I fix this one, I'll fix them all. So here I go, I click on my Facebook icon in my bookmarks and all goes well. Then, a while after, Facebook doesn't respond anymore and I'm send to a page that says "this is probably not the webpage you are looking for!" and it goes on about someone probably trying to hack my Internet and so on. But it's impossible: my network is under a solid WPA/WPA 2 security access. So I try again and click on the FB icon, and it shows me this:
"Invalid URL
The requested URL "/", is invalid.
Reference #9.c2c28f18.1352263449.304a8c9"
View 9 Replies
View Related
Oct 16, 2010
I am trying to set up an access policy on my WRT400N. Whenever an access policy is enabled, all internet acess is completely blocked. This occurs irregardless of what the access policy is supposed to block. Even a blank access policy that allows access to everything and doesn't have any computers registered still blocks everything. How do I get it to stop completely blocking internet access?
View 9 Replies
View Related
Aug 9, 2012
We have a home use WRT160N router linked to a PC desktop and two wireless laptops, Yesterday bought a new I-Phone, but could not link to my network (entered the security key many times). I accidentally connected to computer fix it firm that linked to my PC and wanted a large sum to fix the problem which he said was due to large number of temp?? internet files and once removed he would change the IP address of the desktop computer? Is this diagnosis logical and can I do it on my own. The router is definetely working - both laptops access the internet and I was recently able to hook up a Samsung Blu-Ray player using the same security code I used for the I-Phone.
View 1 Replies
View Related
Nov 2, 2012
This is now an issue with new firmware. I cannot even log into blockbuster.com. I have noticed cookie issues since 2.0.04 firmware installed.
View 9 Replies
View Related
Nov 15, 2012
I've been trying to get FTP Running up on my router for some time now.
I know my current WAN address and have setup a specified folder on my E4200 for the FTP partition. A username for myself has been created with login info and I have forwarded the port I have specified on my router's FTP configuration page.
I try to log into the server, but whenever I try to log into it, I keep getting a "incorrect login information" message back at me.
If I cancel out of that then I get an error message saying it can't find the specified folder and to check the address of the server.
I know the login information information is correct and I've tried changing the password to others of varying lengths.
I've also tried changing the port I'm running the FTP off of incase my ISP has blocked that port, nothing works.
View 9 Replies
View Related
Nov 10, 2012
i have installed lutron lighting in my home and need to configure e4200 so i can access it from outside home with iphone application. Lutron manual says to go to VPN iphone setting and add PPTP connection, server, account and password. I need to do same on e4200 but not sure where to go create pptp connection, accounts and passwords?
View 4 Replies
View Related
Jun 18, 2012
I have my main router, a E4200v2 which I use as a router and it provides wireless signal throughout my house, however reception is not as strong on the upper floor and there is a slight dead spot, so I purchased an E4200 for the uppermost floor.I set the E4200 to bridge mode so it will act solely as an AP.However connecting the two routers LAN to LAN and the AP does not access the internet.Setting a static IP for the router, instead of acquiring one via DHCP causes me to not be able to access the admin page on the AP.
Connecting WAN on the E4200 to the LAN on the v2 does not work either.My goal here is to have my main router on 192.168.1.1 and the AP on 192.168.1.2 where I can access the admin settings for both routers in case I need to make changes.
View 9 Replies
View Related
