Linksys Wireless Router :: E4200 Running Firmware 1.0.03 Build 14?

Dec 18, 2011

I am unable to connect both of my smart phones to the access point.  I am using WPA2 encryption on the AP.  I can connect my phones to other AP's using WPA2.  I have other devices that connect to the AP except my Android phones.  I would like to be able to get some debug logs except the web interface says that the logging fictions are disabled when in bridge mode. Cisco/Linksys tech support: Any troubleshooting tips other than resetting the access point and or reflashing it.

View 4 Replies


ADVERTISEMENT

Linksys Wireless Router :: Low Transmission Rate In E1200 Firmware V2.0.04 (Build 1)?

Nov 1, 2012

the only way i can get 300mbps from this router is by having these settings, it seems the only valid settings to get  300mbps from the router are the following:
 
Network Mode: mixed
Channel Width: auto (20mhz or 40mhz)
Channel : 1
 
if i leave the channel to auto it won't show up as 300.on top of that it doesn't want to stay at 300mbps for very long, sometimes its max rate in inSSDer is only 144 or 156mbps. its the weirdest thing, i think this version of the firmware seems to forget to check for how fast its wireless transmit speed is.When it reboots it only transmits at 144 or 156mbps. i have to go in the basic wireless page and just save the settings to reset it to 300, i don't even have to change anything, it resets its max rated speed back up to 300mbps.and more importantly, are the devs aware of this problem for the e1200 v2 ?

View 3 Replies View Related

Linksys Wireless Router :: EA4500 Firmware V2.0.37 (Build 131047) Feedback

May 7, 2012

Just a few things I've noticed with this build..
 
1.) If you reboot the modem, it seems to loose UPnP settings.  I have to turn UPnP off then back on again in order UPnP to work normally.
 
2.) Probably petty but when I click the Disconnect button under Router Status, the page doesn't automatically refresh like it did with E4200v1.  I have to manually refresh to get the connect button to appear.  The refresh issue is also true within the mobile app.  Again, not an issue with E4200v1.

View 9 Replies View Related

Linksys Wireless Router :: WRT160N - Internet Speeds Reduced After Installing Firmware 2.03 Build 9

Jul 28, 2012

I own the linksys wrt160n v2...It has latest firmware 2.03 build 9...After installing this firmware i have noticed the internet speeds have reduced,the router requires frequent reboots to make it stable.. 
 
i used to have firmware version 2.02 build 15...It was stable unlike the current firmware...i cant find the old firmware anywhere...how do i  revert back to old firmware?
 
All settings are currently at default. 

View 3 Replies View Related

Linksys Wireless Router :: Setting Up An E4200 On A Mac Running OS Lion

Sep 23, 2011

Apparently the setup cd does not work with Mac OS Lion.  Anyone else out there is using this router on a Mac running Lion...if so, how did you set up the router.

View 3 Replies View Related

Linksys Wireless Router :: How To Tell If E4200 Running At Optimal Configuration

Jan 11, 2012

Just picked up the E4200 and used Cisco Connect to install.  Wanted to know a few things?
 
-Windows 7, 64 bit
-E4200 router
-AE2500 adapter
 
1)  How can I tell if its running at optimal configuration?
 
2)  Before with my previous router (netgear) I didn't see my router in Device Manager.  Now its under Network Infrastructure Devices.  It lists the name of my router, under that it lists Microsoft Wireless Router Module??
 
3)  Before with my previous adapter (belkin) I would see my Network Adapter in Device Manager.  I see my network adapter listed, under that Realtek PCI (LAN), but now there is another new device?  Microsoft Virtual WiFi Miniadapter?? 
 
Why are these Microsoft devices showing in Device Manager?  Did they not get installed correctly?

View 2 Replies View Related

Linksys Wireless Router :: Running E4200 With Mac OS X Mountain Lion?

Feb 20, 2012

Running an E4200 with Mac OS X Mountain Lion?

View 3 Replies View Related

Linksys Wireless Router :: Running Firmware Version 1.1.28.14856 On EA6500

Mar 13, 2013

I'm running firmware version 1.1.28.14856 on EA6500 series.

View 4 Replies View Related

Linksys Wireless Router :: E4200 (v1) 5Ghz Disconnects When Running Speedtest?

Feb 15, 2012

I have an e4200 set up using a trendnet TEW-684ub.  Connection on 2.4Ghz and 5Ghz seems fine, but when the 5Ghz network is under load, such as running speedtest, the network drops for a second.  This does not appear to happen on the 2.4Ghz network.
 
2.4Ghz and 5Ghz networks are set to Auto width and channel using WPA2 and I've tried raising the router up a bit to increase airflow to try to eliminate overheating as a possible issue.  I'm also running the latest firmware...1.0.0.3, I believe.

View 5 Replies View Related

Linksys Wireless Router :: E4200 - Running In Bridge Mode /Automatic DHCP?

Dec 9, 2012

I am trying to determine the best way to setup my E4200 V2 so that it is “uplinked” correctly to a Comcast Dory Modem/router.  Currently we have the E4200 V2 router plugged into the Comcast Dory Modem/Router using a CAT6 cable from one of the Ethernet ports on the Comcast device to the WAN port on the E4200.  The E4200 is set to “Automatic Configuration - DHCP.”  
 
We are trying to do two things.  First better WIFI in the center of the house and for a TV located next to the Comcast device, and second, have all devices in this house see and access all other devices including the Samsung SmartTV, my son’s two systems upstairs, the 3 systems in the room with the E4200, and the one network printer.  In the room with the E4200 we have 3 computers and one network printer.  3 of those 4 devices support WIFI so we don’t have to use all 4 Ethernet ports on the E4200.     
 
I see others talking about running the CAT6 cable to an Ethernet port on the E4200 instead of the WAN port and setting it to “Bridge Mode.”  Right now the system appears to be working fine although we are sometimes experiencing brief dropped connections with the devices hardwired into the E4200. 
 
Should I be running the E4200 in “Bridge” mode or “Automatic DHCP” mode and which port on E4200 should the CAT6 from Comcast be plugged into?

View 9 Replies View Related

Linksys Wireless Router :: Where To Get New Firmware For E4200

Apr 14, 2012

There is a new firmware for the E4200 router and I have no clue how to get the file. I've been searching in the support section » download tab without success. Any link to the new firmware how to get it?

View 1 Replies View Related

Linksys Access Point :: Download WAP610N Firmware Version 01.0.00 Build 832?

Dec 21, 2011

Is there anywhere I can download  WAP610N Firmware Version 01.0.00 build 832?  I have two units with this firmware version that work OK.  I recently purchased another unit that has WAP610N Firmware Versions 1.0.01 and and can only access an IP address if I do not use any security. I also spent a lot of time on the phone with Linksys support to no avail.

View 6 Replies View Related

Linksys Wireless Router :: E4200 Tomato Firmware?

Jul 28, 2011

I was looking for alternative firmwares until Linksys fixes their broken device.What do you guys make of this Tomato firmware?  Do you think it has usb drive and Media Streaming (Twonky) support?

View 2 Replies View Related

Linksys Wireless Router :: Can't Upgrade Firmware On E4200

Oct 18, 2012

The file uploads fine, but I get an error message saying the router can't be updated atthe moment. I want to do the update because as of now, the router can't see my drive connected on usb (one ntfs partition and another one called wbfs, maybe that one is causing the issue about the drive).

View 2 Replies View Related

Linksys Wireless Router :: How To Upgrade Firmware On E4200

Jul 2, 2012

I currently have  Model name: Linksys E4200 Firmware version: 1.0.04 build 11  Software version: 1.4.12100.0
 
I'm trying to upgrade to the second and most up to date version. (Version: 2.0) firmware. Any links or way to do this? I tried doing it through my router settings under administration -> firmware upgrade but it won't update automatically. I have to find the actual update file and update the firmware through that.

View 2 Replies View Related

Linksys Wireless Router :: Cannot Update E4200 Firmware

Dec 13, 2012

Nom du modèle : Linksys E4200Numéro de modèle : E4200Numéro de série : 01C10C17152754Version du microcode (firmware) : 1.0.03 build 14OS : Windows 8Version du logiciel : 1.4.12284.0Type de connexion (réseau étendu) : DHCPAdresse IP (réseau local) : 192.168.0.1Adresse IP (réseau étendu) : 192.168.1.101Adresse IP de l'ordinateur : 192.168.0.135
 
I downloaded this file :[URL]I upgraded it, I typed 192, etc. in firefox, when to the maintenance tab, put the dowloaded file in "new firmware location" and clicked "update". It said: "you put a wrong file".this is written in the same tab : Current Firmware Version 6.0.0 Build 100906 Rel.43560

View 1 Replies View Related

Linksys Wireless Router :: Does It Value To Update E4200 Firmware To 1.0.03

Oct 2, 2011

I am waiting for half year. And I read the forum know the NAT though put perfromance of 1.0.01 is poor than that of 1.0.03 of E4200.Actually a bit disappoint to CISCO LINKSYS products. It is not value to cost high selling price with poor functions and performance.

View 4 Replies View Related

Linksys Wireless Router :: Download Source For E4200 V1.0.0 Firmware?

Aug 1, 2011

link to the original v1.0.0 firmware for the E4200.  That was the best firmware for me and sadly I can't find a link to go back.  v1.0.0 really had no problems for me.  I initially skipped v1.0.1 becuase it disabled IPv6 which is a feature I want.  v1.0.2 broke my YouTube and Netflix streaming.  So I went back to v1.0.1 and my Netflix and YouTubue steaming returned to normal but I lost IPv6.
 
Any solution to Netflix and YouTube streaming problem on v1.0.2 when IPv6 is configured.  (I'm positive the video is streaming over IPv4, but the IPv6 connectivity is available.)

View 9 Replies View Related

Linksys Wireless Router ::E4200 - Why Firmware Can Only Set 5Ghz Broadcast

Dec 30, 2011

I had a e4200,and i used 5ghz wireless.i can't set it to channel 149 or other high channel,my old wireless ethernet card can only support that.make the next version of the firmware can setting 5ghz channel to channel 149、153、157、161.

View 2 Replies View Related

Linksys Wireless Router :: E4200 Firmware 1.0.02 Blocking VPN Access?

Aug 6, 2011

I cannot connect to my company’s VPN after installing the current firmware (FW_E4200_1.0.02.013_US_20110524) on my E4200 router. Version 1.0.01 was on the router when I received it, and it worked without issues. As soon as I upgraded version 02, I could not initialize a VPN connection. When I try to start a VPN session, I get a "page not found" error when attempting to initiate SSL VPN service using a Microsoft Forefront Unified Access Gateway. VPN pass through is enabled for all protocols in the e4200’s setup. As soon as I revert to firmware 01, everything works fine again.
 
I did a fresh download and re-flashed the 02 firmware just to make sure that it wasn’t an issue with a bad download or a faulty flash. The problem is consistent and repeatable. I have upgraded and downgraded twice, and the results are exactly the same. My VPN connection works with firmware 01, and it fails with version 02. There is a something different in the 02 firmware that is blocking VPN access.

View 9 Replies View Related

Linksys Wireless Router :: E4200 V2 With Firmware 2.1.39.145204 Gets Stuck

Dec 24, 2012

I've tried to upgrade/downgrade process twice with the same result. After few days without any issue 2.1.39.145204 gets stuck (=routing to internet doesn't work although I can ping from wireless network to all LAN IPs) and I need to reboot the router.
 
I have about 7 devices. Guest network is disabled, parental control is disabled, USB is not used, DHCP service is used, WPA2 mixed personal mode is used, MAC filtering is disabled, DMZ is disabled, DDNS is disabled, port triggering is not used. All the rest of settings are in default values.
 
As far as I notied the previous version 2.1.39.144146 doesn't get stuck at all.

View 1 Replies View Related

Linksys Wireless Router :: E4200 Cannot Use The Client Name With Stock Firmware

Mar 10, 2012

I've assigned an ip address to my htpc using dhcp reservation. On my old router I could use the client name, for instance: ssh name@clientName Instead of: ssh name@ipAddress Currently I cannot do this with the stock cisco firmware (unless I'm mistaken). Is there something I have to do to get it working? Or do I have to resort to tomatoUSB/WRT.

View 1 Replies View Related

Linksys Wireless Router :: E4200 Firmware Upgrade Failed?

Aug 24, 2011

I just bought a Cisco E4200 (from someone on Ebay, so returning is probably not an option).  I was in the process of setting it up when it wanted to do a Router Update.  Unfortunately, it did not specifically say to not do it WIRELESS.  We had a disconnection in the upgrade process.  Now the Power light just blinks.  I can ping it from a hard-wired PC, but cannot get to the Administration Web page to retry the firmware update (I did download it from the site).  Also Cisco Connect cannot connect to the router.
 
Oh Yes, I have tried holding reset button for 30 seconds, unplugging for 30 seconds, and replugging in the router.  I do not get any different results.

View 6 Replies View Related

Linksys Wireless Router :: E4200 (firmware 1.0.03) Fails To Renew IP Address

Dec 1, 2011

After an indeterminate period my E4200 (firmware version 1.0.03) stops renewing the Internet IP address. This happens in both router mode and bridge mode.In router mode the E4200 is set for DHCP and connected to the cable modem, in bridge mode it is connected to a Dell switch  with DHCP being provided by my Win2008R2 server.It appears that the device stops recognizing the existence of the Internet port - no lights come on when a cable is plugged in - whether connected to the cable modem or my Dell switch. Plugging the same cable into one of the 4 lan ports and that port lights up immediately (i.e. it is not a patch cable problem).If the E4200 is left switched off for some time (possibly days) it will work properly again for a while.

View 6 Replies View Related

Linksys Wireless Router :: E4200 V2 Firmware 2.0.37.131047 Manual Download?

Apr 27, 2012

The device has been trying for days to auto-download and all it does is fail constantly.  Saying that my connection is slow - gee, I have FiOS, I know it's not slow,maybe it's your Servers Cisco?Well, where can I obtain the direct DL link to that firmware file instead of relying on an unreliable device to get it and apply for me?

View 4 Replies View Related

Linksys Wireless Router :: E4200 / Firmware 1.0.03 - Internet Speed Maximized

Oct 6, 2011

It is the router Cisco Linksys E4200.

My situation before I bought the router:
- my Internet speed is 120/20 (Mbps download / Mbps upload)
- speed test with my ISP gives 125/20 for 99% of the tests- speed test with [URL]  gives 125/20 for 99% of the tests
- I never have had a router; my PC is connected directly to the cable modem
- My ISP is Vidéotron from Quebec in Canada : [URL]

My new situation with the new router :
- last Tuesday, I bought the router Cisco Linksys E4200
- the installation  went fine and Internet works well
- during the installation process, the firmware is upgraded to 1.0.03
- speed test with my ISP gives 100/20 for 99% of the tests
- speed test with [URL] gives 100/20 for 99% of the tests 

My observations :
- according to router status port, Internet port is 1 Gbps
- according to router status port, port  1 (where my PC is connected) is 1 Gbps
- it seems that speed cannot get more than 100/20 with the new router
- when I disconnect the router and I reconnect my PC directly to the modem cable, I still get 125/20 

Calling Cisco support :
 - Many tests are done during 3 chat sessions
- The speed is still 100/20
- The recommendation is to replace the router with a new one  

Friend support :
- A friend of mine brought his router which is the same as mine- The speed is still 100/20 with his router 

New router  :
- As recommended by Cisco support, I got the router replaced from the store.
- I installed the new router
- During the installation process, the firmware is not upgraded; the firmware is 1.0.01
- The speed is now 125/20
- I upgraded the firmware to 1.0.03
- The speed is now 120/20
- I downgraded the firmware to 1.0.01
- The speed is now 125/20

Conclusion :
- My speed is maximized at 100/20 with the firmware 1.0.03
- I will stay with firmware 1.0.01 until firmware1.0.03 is corrected.

View 8 Replies View Related

Linksys Wireless Router :: E4200 - Restore Previous Version Of Firmware?

Dec 27, 2012

I have an E4200 router with 3 WET610N access points.  I did the firmware update on the E4200 router about 2 weeks ago so my son could use his xbox when he got home after 4 months of being away.  Everything seemed to work OK as far as I could tell....but when he went to sign into xbox live and watch Netflix, it will load to 98% and stop.  A friend of his came over with the new Slim xbox 360 with built in wireless and it will connect fine on its own, if we hook up one of the 610N's to it, it will load to 98% on Netflix and stop again with error code R8152.  Both of my older xbox's will hook up and play on xbox live, just not work with Netflix.

I also noticed, it shows the WET610N as a hard wire on xbox and will not search for any wireless networks, I have 2.  The newer Slim xbox360 will search out both networks on its own if you allow it to use its internal wireless.  This only happened since the firmware update.  And this equipment was working fine before this.  Is there a way I can restore the previous version of firmware? 

View 4 Replies View Related

Linksys Wireless Router :: E4200 With Bad Firmware Cannot Use External Storage Settings

Apr 1, 2013

This firmware bad, because my sync program, can't set create date of files on external usb storage connected to router, on 1.0.04 - all good.

View 5 Replies View Related

Linksys Wireless Router :: E4200 And Slingbox Firmware Not Connecting / Playing

Dec 9, 2011

I have a new E4200 with the latest firmware and my slingbox seems to not be playing nice with the router.  It refuses to take the IP I reserved for the SB, but always defaults to 192.168.2.254.  I use a 2 subnet just in case you're wondering.  I have tried multiple reboots and the IP does not change.  I have tried turning off UPNP, figuring that was hijacking the dhcp server, but that hasn't changed anything. I also notice that a few of my connected devices do not show up in the dhcp list, yet they connect and work ok. 

View 2 Replies View Related

Linksys Wireless Router :: E4200 And WET610N No Changes To Bridges Before Firmware Update

Feb 6, 2012

Okay so I have been using my E4200 router and WET610N bridges for a while now without any issues really until yesterday when I updated the firmware on the 4200 now none of my WET610N's (I have 2) can connect via wireless at all. At first I thought it was a a wireless issue but I have other devices that connect up just fine via wireless.I've made no changes to the router or the bridges before the firmware update.
 
If I hook the bridge directly to the router I can access it and configure it, but looking at the "Status" page, I see the bridge try and connect wirelessly but is quickly disconnected.  Range isn't an issue as in my testing the bridge was 2 feet from the router.I've update the bridges to the latest firmware and have verified a 100 times that the settings on both my router and the bridges are set correctly (when the bridges are hooked up via network card).

View 1 Replies View Related

Linksys Wireless Router :: Firmware Upgrade E4200 Can No Longer Be Accessed

Oct 18, 2012

automatic firmware upgrade my E4200 can no longer be accessed.

View 6 Replies View Related

Linksys Wireless Router :: Choppy Video Streaming After Upgrading E4200 Firmware

Jan 2, 2012

Video streaming was fine until I upgraded the firmware. Is it possible to downgrade the firmware?

View 3 Replies View Related

Linksys Wireless Router :: E1200 Ver.2.0.03 (Build 10) Upgrade Stalls At 98%

Aug 8, 2012

Started a upgrade of my firmware to Ver.2.0.03 (Build 10) for the E1200 H/W v2 and at 98% it stalled this was over wired connection and via http not https.
 
I'm really disappointed which this router because in all honesty its been one of the slowest I have ever bought whereas the Wireless-N doesn't truly work with N speeds being like 3-9Mbps where if I disable WMM and switch to B/G Only then my speeds jump to 20-30Mbps.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved