Linksys Wireless Router :: E1200 Ver.2.0.03 (Build 10) Upgrade Stalls At 98%
Aug 8, 2012
Started a upgrade of my firmware to Ver.2.0.03 (Build 10) for the E1200 H/W v2 and at 98% it stalled this was over wired connection and via http not https.
I'm really disappointed which this router because in all honesty its been one of the slowest I have ever bought whereas the Wireless-N doesn't truly work with N speeds being like 3-9Mbps where if I disable WMM and switch to B/G Only then my speeds jump to 20-30Mbps.
View 2 Replies
ADVERTISEMENT
Nov 1, 2012
the only way i can get 300mbps from this router is by having these settings, it seems the only valid settings to get 300mbps from the router are the following:
Network Mode: mixed
Channel Width: auto (20mhz or 40mhz)
Channel : 1
if i leave the channel to auto it won't show up as 300.on top of that it doesn't want to stay at 300mbps for very long, sometimes its max rate in inSSDer is only 144 or 156mbps. its the weirdest thing, i think this version of the firmware seems to forget to check for how fast its wireless transmit speed is.When it reboots it only transmits at 144 or 156mbps. i have to go in the basic wireless page and just save the settings to reset it to 300, i don't even have to change anything, it resets its max rated speed back up to 300mbps.and more importantly, are the devs aware of this problem for the e1200 v2 ?
View 3 Replies
View Related
Aug 4, 2012
I just purchased a new E1200 router with firmware version 2.0.01 and downloaded the latest version 2.0.03 and tried to install it through the router. When I choose the downloaded file and try to start upgrade I immediately get an error "The Image File is Incorrect". I redownloaded it and tried again with the same error. how to get past this and upgrade the firmware?
View 9 Replies
View Related
Apr 13, 2012
I am trying to upgrade the firmware on my Linksys v1 router from 1.0.02 to 1.0.03 over a remote 56Kb circuit. I appear to be having a timeout problem. The upgrade always fails. I have upgraded several E1200s in my office over ethernet, and the upgrade appears to finish when the progress bar is at 15%. However, on my remote upgrade, the progress bar gets to 98%, hangs for a few more seconds, and then pops up a window with "Upgrade failed".
I suspect that there is a timeout on the upgrade process, and that I can't upload the 3.8 MB firmware file fast enough. If so, is there any way to increase the upgrade timeout?
View 2 Replies
View Related
Aug 21, 2012
I was asked to connect directly to the modem to be sure that it worked before beginning to install the E1200. When I connect my laptop (Win7) to an available wired ethernet port on my WR54GS I can connect to the internet. If I unplug the internet input to the router from the modem and connect that to my computer, I do not get an internet connection. I am using a Motorolla SB5120 modem connected to comcast.
View 3 Replies
View Related
Jan 15, 2013
I have a Cisco E1200 router that is currently running firmware version 1.0.03 build4 Mar 1, 2012. Can I upgrade to the latest version 2 firmware ? How do I know if my router hardware will support it ?
View 4 Replies
View Related
May 27, 2011
This issue started about 6 months ago. I have noticed the following issues:
1. I cannot download large files. It starts downloading then it stalls.
2. I cannot download videos on Youtube and other video site to stream the video. In [URL] the test shows 100% complete but the test keeps on running and upload speed goes down.while running the upload speed test on [URL] sometimes it cannot connect to server to upload the file. When it connects to the server I get error saying that it cannot read the file it uploaded.Had Comcast come out to take a look at the cable and they claim that it was the PC's fault and not the cables's fault. I have the cable coming out of the modem to a linksys router ( WRT54G), then to my PC. I connected the cable directly from the modem to the PC and still had the same proble.
I have the following:
System
Manufacturer: Velocity Micro
Model: Edge V420
Processor: Intel core 2 Quad CPU Q9550 @ 2.83 GHz
Memory(RAM): *.00 GB
[code]....
View 1 Replies
View Related
Dec 18, 2011
I am unable to connect both of my smart phones to the access point. I am using WPA2 encryption on the AP. I can connect my phones to other AP's using WPA2. I have other devices that connect to the AP except my Android phones. I would like to be able to get some debug logs except the web interface says that the logging fictions are disabled when in bridge mode. Cisco/Linksys tech support: Any troubleshooting tips other than resetting the access point and or reflashing it.
View 4 Replies
View Related
May 7, 2012
Just a few things I've noticed with this build..
1.) If you reboot the modem, it seems to loose UPnP settings. I have to turn UPnP off then back on again in order UPnP to work normally.
2.) Probably petty but when I click the Disconnect button under Router Status, the page doesn't automatically refresh like it did with E4200v1. I have to manually refresh to get the connect button to appear. The refresh issue is also true within the mobile app. Again, not an issue with E4200v1.
View 9 Replies
View Related
May 22, 2011
I have a old version on my CSC SSM module 6.0, I want to upgrade to the last version.I never use the CSC SSM module, so first i must activate it using the activation key right ?
From my understanding I need to install first the release csc6.1-b1519, i have tryed to find it on cisco software center, but it seems unavaiable. How upgrade my CSC SSM module?At last when I will upgrade the CSC SSM, the activation key remain vaild? (I have also the plus license.)
View 11 Replies
View Related
Jul 28, 2012
I own the linksys wrt160n v2...It has latest firmware 2.03 build 9...After installing this firmware i have noticed the internet speeds have reduced,the router requires frequent reboots to make it stable..
i used to have firmware version 2.02 build 15...It was stable unlike the current firmware...i cant find the old firmware anywhere...how do i revert back to old firmware?
All settings are currently at default.
View 3 Replies
View Related
Dec 29, 2011
I have a couple of Droid Incredibles, and when I use them connected to my Wi-Fi (even tho I have unlimited data, the cell signal strength is not that high in my home -- I'd rather use the Wi-Fi) they'll run for 10-15 minutes, then hit a brick wall. Internet traffic stops, for all devices conected. ROuter has to be re-booted.url...but I also read some where in this forum that simply disabling AES would work.
View 2 Replies
View Related
Dec 24, 2012
My home network uses a Cisco router connected to a cable modem. The router has a WAP and a second WAP is connected with power over Ethernet connection. Both WAP have strong signals. We have PC's, a Mac and several Iphones connected wirelessly. When using the Internet, the computers and phones seem to stall when moving from one web page to another. This happens with one or several devices in use, so it does not appear to be related to volume. Re-booting the modem and router usually corrects the problem, but not always.
View 1 Replies
View Related
Dec 22, 2012
I have 3 Wireless Devices connected to my Router which is a Ipad, Ipod Touch & laptop.I have 2 hard Wired conneted to my Router which is a ps3 and a Desktop. How can i have great speeds and reliable connection on all of them.
View 9 Replies
View Related
Jun 5, 2012
I have opened my NAT for xbox using Port Triggering , but I cannot open my NAT for the PC because it uses no ports!I cannot host a match using any MMO game , and I cannot host any MW3/Black Ops matches too!
View 7 Replies
View Related
Aug 12, 2012
Setting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password).
View 9 Replies
View Related
May 1, 2013
I purchased E1200 and have a problem. I have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.
View 4 Replies
View Related
Nov 7, 2011
I have a Panasonic Visio tv, I have a LINKsys E1200 that is connected to my Cable Internet. I have successfully connected the wireless to my laptop and have a guest network that has been tested and works as well. I bought a Sharp Blu Ray player that has wireless capability connected to the TV with HDMI cable and the LAN adapter is in the player. When I had the Blu Ray downstairs I had it connected to the LINKsys thru an ethernet cable and didn't use the adapter, but I wanted to take it upstairs and use it on that TV. CANNOT establish an internet connection?
View 2 Replies
View Related
Jan 4, 2012
Is it possible to use a Linksys E1200 as a repeater? If so, how do I set it up?
View 3 Replies
View Related
Oct 23, 2012
Bought a new Samsung tablet and a Cisco wi fi router. But I don't have the CD drive to activate the wi fi router. I am using the Cisco linksys E1200.
View 1 Replies
View Related
Dec 29, 2011
I can't see where to set a user name on my E1200. I set a password for the web interface then it boots me out and I am promted for the password and username.I don't want to download and configure my router with some poorly written software for my mac; why can't I just do it all through the good old web interface???? I'm able to set everything else up fine but when i set the password I am basically rendering the web interface usless and have to reset the router!! (running Lion, latest build with 8gigs of ram and N wirless adaptor in lappy)
Ok, so I was given this router for free so I shouldn't complain but I do not see any speed increase over my 6 year old 54G rinning wrt, perhaps I need summin better than this $50 walmart special Getting about 10mps download which is also the theoretical max of G right)
View 6 Replies
View Related
Jun 9, 2012
I set my router to allow my xbox360's mac address, not knowing that it would kick out all of my other devices. So now I can't access my own router and I need to reset it. How do I do that?E1200 series linksys router. I'm looking for an ethernet cable and my installation disk right now to see if I can connect with the cable and maybe use something on the disk if I have to.
View 1 Replies
View Related
Dec 26, 2012
I replaced my broken modem with a new Motorola 3360 as recommended by my ISP. The new modem works fine connected directly to my PC. When connecting the modem to the Cisco E1200 router, the same one I had with the older modem, the E1200 says I'm not connected to the PC. I've triple checked the wired connections from the modem to the router and then to the PC. I've swapped out cables and verified that they all work when used directly from the modem to the PC. I'm thinking some settings from the old Westell modem are messing with the connectivity of the new E1200 router.
View 2 Replies
View Related
Apr 16, 2013
my wifi router is E1200 at first it works very fine but then when the time you unplugged it and turn it on again it won't work already i mean its working the lights are on and blinking but there's no wifi... why does it happen??? i don't understand...i have already did the 30-30-30 rule the hard reset thin but still nothing's change...
View 5 Replies
View Related
Dec 29, 2012
i'm having connection issues requiring frequent reboots of my router. it starts with internet slowdown to a crawl, then it times out and lastly the webinterface is not even responding when i try to access it to reboot. Requiring me to manually unplug. this happens once a day atleast.
Sometimes it recovers after a few minutes and get on the net.i've tried flashing, reflashing, re-reflashing , resetting , re-resetting, to no end. And all the usual tricks tech support ask to do.
i didn't use to have this problem before the firmware update
08/31/2012
Ver.2.0.04 (Build 1)
i would just like to flash to the previousl version and test if this still happens.
View 9 Replies
View Related
Jan 19, 2012
I have been attempting to set up a linksys wireless-n e1200 router on my hp p6-2007c (Windows 7 SP1, 64-bit) desktop pc for the last day and have exhausted everything i can think of. The previous router was a linksys WRT54G and it worked fine. However, upon setting up this new router i get a "no internet access" message accompanied by the little yellow triangle and the ability to still connect to my router via its ip address to alter its configuration. The connection status for the network and the internet is identical for all the laptops in my house. I originally attempted setting up the router using Cisco's setup program. At its conclusion, the setup program informs me that i am connected to the router, but my internet connection has been lost (even though it was never there) I have tried starting over from scratch by resetting the router back to its default settings and using a variety of different channels (Auto, 1, 6, and 11), frequencies, etc. I have uninstalled norton antivirus, disarmed the windows security programs, made sure of TCP/IP settings, rolled back, uninstalled, and finally updated firmware, uninstalled/reinstalled driver for wireless card, disabled/enabled the card itself, deleted all other previous network profiles still present in the "Manage Wireless Networks" screen, and probably some other suggestions i came across in this forum. They all failed with the same results, i.e. the ability to connect to the network locally and having no internet access.
View 1 Replies
View Related
Jan 17, 2013
I have a linksys e1200 wireless router and the internet port does work. Is there a way to make one of the lan ports the internet ports?
View 1 Replies
View Related
Sep 21, 2012
I can connect to the guest account but it cannot resolve DNS addresses; how should the router be set up?
The regular (non-guest) account works as advertised. The E1200 is connected to my Verizon modem/router. I have tried disable/enable of DHCP on the E1200; I have tried setting the E1200 Static DNS 1 to my Verizon router IP address without success.
View 6 Replies
View Related
Mar 26, 2012
I just installed an E1200 router and used the CD to take care of the software work. I Cannot connect to it by WiFi. I still have to use a cable connection.
View 4 Replies
View Related
Jul 6, 2011
I want to prevent a wired pc with a static ip from accessing the internet on an e1200 router, but the computer does not show up in the list under "parental controls". I have tried adding it to the dhcp reservation table manually, but it still does not show up. There are, however, several unspecified "network devices" on the list. How can I do this?
View 7 Replies
View Related
Jan 3, 2013
I wish to have a home network using the E1200 without an internet connection. I have a netbook (Lenovo S100) and a Samsung Galaxy Note II. I want to be able to have both connected to the router so I can interface the two devices using a program such as Teamviewer.
View 1 Replies
View Related
Mar 25, 2012
I just got a Macbook Air and couldn't get connected at home so I went and bought a new router (our other router was old!!). We purchased the E1200. Our Dell desktop seems to have a fine connection, but my MacBook Air and my husbands laptop are really slow when on the internet.
View 1 Replies
View Related
Sep 10, 2012
I'm having getting my E1200 to work is this; I'm connected wirelessly with an N-adapter to the router, my roomate is connected directly with an Ethernet cable and to the modem. Whenever he logs ons or logs off from internet I GET DISCONNECTED! Its very frustrating. At first I kept wondering why I would get frequent Disconnects, until I matched exactly the times he would log on or log off. I've never seen this type of problem before in my previous router?
View 9 Replies
View Related
