the only way i can get 300mbps from this router is by having these settings, it seems the only valid settings to get 300mbps from the router are the following:
Network Mode: mixed
Channel Width: auto (20mhz or 40mhz)
Channel : 1
if i leave the channel to auto it won't show up as 300.on top of that it doesn't want to stay at 300mbps for very long, sometimes its max rate in inSSDer is only 144 or 156mbps. its the weirdest thing, i think this version of the firmware seems to forget to check for how fast its wireless transmit speed is.When it reboots it only transmits at 144 or 156mbps. i have to go in the basic wireless page and just save the settings to reset it to 300, i don't even have to change anything, it resets its max rated speed back up to 300mbps.and more importantly, are the devs aware of this problem for the e1200 v2 ?
Started a upgrade of my firmware to Ver.2.0.03 (Build 10) for the E1200 H/W v2 and at 98% it stalled this was over wired connection and via http not https.
I'm really disappointed which this router because in all honesty its been one of the slowest I have ever bought whereas the Wireless-N doesn't truly work with N speeds being like 3-9Mbps where if I disable WMM and switch to B/G Only then my speeds jump to 20-30Mbps.
I am unable to connect both of my smart phones to the access point. I am using WPA2 encryption on the AP. I can connect my phones to other AP's using WPA2. I have other devices that connect to the AP except my Android phones. I would like to be able to get some debug logs except the web interface says that the logging fictions are disabled when in bridge mode. Cisco/Linksys tech support: Any troubleshooting tips other than resetting the access point and or reflashing it.
1.) If you reboot the modem, it seems to loose UPnP settings. I have to turn UPnP off then back on again in order UPnP to work normally.
2.) Probably petty but when I click the Disconnect button under Router Status, the page doesn't automatically refresh like it did with E4200v1. I have to manually refresh to get the connect button to appear. The refresh issue is also true within the mobile app. Again, not an issue with E4200v1.
I own the linksys wrt160n v2...It has latest firmware 2.03 build 9...After installing this firmware i have noticed the internet speeds have reduced,the router requires frequent reboots to make it stable..
i used to have firmware version 2.02 build 15...It was stable unlike the current firmware...i cant find the old firmware anywhere...how do i revert back to old firmware?
I have had a DIR-655 for years, and this is a treat - channeling everything from IPTV, to a fast fiber connection, transfers - no sweats.
Then I had to setup a router for a friend, and recommended the DIR-615.
Setup the router, and max it would connect with was 150mb - I changed the settings accordingly: auto channel scan channel width: auto 20/40mhz
So this "opened" up the 300mb speed - however only for 5 mins, then it falls down to 150mb.
My laptop (lenovo) connects to the dir-655 just fine at full speed, and this is also the machine I used for testing the dir-615.
It's ax Hx firmware, FW: 8.04
What I can conclude by using inssider, and xirrus wifi inspector is that it generates 2 channels - and then after 5mins of connectivity looses a channel, and then the speed drops.
I got a new router from the dealer, same issue. Then a friend of mine lent me an ancient dir-615, and interestingly enough this had the same configuration option of "Transmission rate" in the wireless settings page! Just like the dir-655. and also connects at 300mb...
i'm having connection issues requiring frequent reboots of my router. it starts with internet slowdown to a crawl, then it times out and lastly the webinterface is not even responding when i try to access it to reboot. Requiring me to manually unplug. this happens once a day atleast.
Sometimes it recovers after a few minutes and get on the net.i've tried flashing, reflashing, re-reflashing , resetting , re-resetting, to no end. And all the usual tricks tech support ask to do.
i didn't use to have this problem before the firmware update 08/31/2012 Ver.2.0.04 (Build 1)
i would just like to flash to the previousl version and test if this still happens.
I just purchased a new E1200 router with firmware version 2.0.01 and downloaded the latest version 2.0.03 and tried to install it through the router. When I choose the downloaded file and try to start upgrade I immediately get an error "The Image File is Incorrect". I redownloaded it and tried again with the same error. how to get past this and upgrade the firmware?
When I bought my E1200 router my primary (in fact only) computer was a Windows laptop. Since that time I bought a MacBook Pro and have been using that as my primary computer. The Mac is running on the latest OS (Mountain Lion).
I would like to install the latest software to maintain the router on my Mac but I was told several months ago that there was no update available for Mountain Lion. If that has changed, and if so then where can I download the appropriate software?
I am trying to upgrade the firmware on my Linksys v1 router from 1.0.02 to 1.0.03 over a remote 56Kb circuit. I appear to be having a timeout problem. The upgrade always fails. I have upgraded several E1200s in my office over ethernet, and the upgrade appears to finish when the progress bar is at 15%. However, on my remote upgrade, the progress bar gets to 98%, hangs for a few more seconds, and then pops up a window with "Upgrade failed".
I suspect that there is a timeout on the upgrade process, and that I can't upload the 3.8 MB firmware file fast enough. If so, is there any way to increase the upgrade timeout?
I have a little problem with my new E1200. Before the E1200 I had a WRT160N that was bricked to death by a power surge due upgrading the firmware. Till that moment the WRT160N met al the required specs as told in the description..I have from my ISP a 40Mbit cable line and was always downloading at those speeds wired aswell as wireless...
Now with the E1200 I get the 40Mbit only wired... wireless it only allows it up to max. 20Mbit.I figured that I didn't do anything different than the Linksys I had before..I'm working with a MacBook from late 2007 running OSX Lion 10.7.2, Built-in AirPort Extreme card (802.11a/b/g/n)My wireless setting with a WP2 Personal Security Mode
I bought a new E1200 this fall when I got a new Internet provider who recommended it to replace my really old one. It worked fine until a month or so ago when it would occasionally disconnect. At first I thought it was my Internet company but I started using the Cisco Connect app to fix it after restarting the router. The first time it worked great for about 2 weeks, but a few days ago it started disconnecting several times a day. Now it doesn't last 10 minutes before it quits. It tells me the firmware is up to date
I have a Cisco E1200 router that is currently running firmware version 1.0.03 build4 Mar 1, 2012. Can I upgrade to the latest version 2 firmware ? How do I know if my router hardware will support it ?
For an N300 model F9K1002V4 router, how can I tell if it's transmitting in N mode? I have two newer laptops that are capable of receiving the 802.11N signal but are only receiving at 54mbps. The router is set to transmit at b/g/n rates.
I have a year old E1200 router. I just updated the firmware today, made adjustments to the MTU range to suit cable service and selected a different channel (9) as the neighbors were mostly on channels 2 and 6.My question is really in regard to the speed results of the router. In the immediate room where the router is located I am getting 17.6 Mbs download speed/ 3.53 upload speeds but if I move to my living room - less than 20 feet away and a few walls - the upload speed drops sharply to 3.21 Mbs download/3.21Mbs uploas.I have read where the router placement can be key. My router is sitting on the desktop. If I elevate the router will it improve performance 20 feet away or should I invest in upgraded router like a E3200 or look into a plug in type repeater?
Is there anywhere I can download WAP610N Firmware Version 01.0.00 build 832? I have two units with this firmware version that work OK. I recently purchased another unit that has WAP610N Firmware Versions 1.0.01 and and can only access an IP address if I do not use any security. I also spent a lot of time on the phone with Linksys support to no avail.
If I send video file(overall bit rate is 17.5Mbps) to client with 2.4Ghz band, it always freezes and go repeatedly around 1 second interval. the distance around 10m away without any wall, open space actually.
But same condition with above, cheaper wireless router no problem at all. It happens only with EA4500. And there are no any parameters setting menu actually.
I have been disappointed by the range of the EA4500 compared to previous routers, but I am most puzzled by it's behavior. I may get an "excellent" connection close to the router (one room away) and speeds up to 65 Mps, but after a few minutes of surfing the web the signal strength and speed can drop substantially.
The problem is the worst at a distance (one floor down in our house, maybe 30 feet away in total) where the signal strength may start at "good" and a speed of perhaps 30 Mps, but then after 3-4 minutes drops to "poor" and maybe 5 Mps.
I've spent parts of the past five days buying and exchanging several WAP4410N units because I was not able to achieve anything close to a 300Mbps data rate. I also tried various wireless-n network cards which were known to be configured correctly for 300Mbps speeds with no luck.
The highest speed I was able to achieve was 130Mbps, which is an indication that channel bonding is not in effect.
Then I came across another post in the forums:
WAP4410N does not exceed 130Mbps in N mode at close range.
where the OP mentions recently upgrading to firmware 2.0.4.2, though not treating that as the cause of his problems.
On a lark, I tried downgrading to both firmware 2.0.2.1 and firmware 2.0.3.3, and to my surprise, I was able to achieve the full 300Mbps data rate with both firmware versions.
When I reverted back to 2.0.4.2, I was not able to achieve the full 300Mbps data rate.
So, right now, I downgraded to firmware 2.0.3.3 so I can get the higher data rate, though there are other quirks to deal with.
Furthermore, when I do a web search of reviews, I can see that the inability to achieve the 300Mbps data rate is a huge source of complaints.
The coaxial"or any other metal cable" was using for transmission signals(before fiber optic) the coaxial need repeater every 2 or 3 Kilo meter,because the signal will be attenuation when pass through the cable,when we transmission electricity to far places ,we use transformer to rising the voltage to 10000 or 100000 volt
I have a home network running on a Linksys WAG320n and i have attached to it a WD MyBookLive (w Gigabit Ethernet). I am connected on the network via my Dell with a Intel(R) WiFi Link 5300 AGN. I am not able though to connect on N range. I have installed the latest drivers from Intel but nothing changed. When i try to copy a file from my computer to the WD Network drive the transfer rates are very slow. I get Max 2MB/s - 3MB/s while if i connect my computer with a wire the speed goes up by 3-4 times more.
How can I see network rate of other computers connected to my WRT54GL wireless router?I have admin password and I want to see how much bytes/sec received and sent from all the computers connected to the router.
I just bought a synology NAS ds212j . I updated to DSM4.0. I purchased 2 Seagate ST2000DM001 Barracuda 7200RPM 2 TB SATA 6 GB/s NCQ 64 MB Cache 3.5-Inch Internal Bare Drive
My e3200 has the latest 1.0.04 firmware I'm backing up via time machine(mac book pro) in MAC 10.7.4 which has a wireless N card.
in Utilities (activity monitor)I'm only getting 9 megabytes per second , why is it so slow? I feel like it's taking forever. e3200 says it does up to 300 megabytes per second. any possible settings causing this?
a backup of 202 gigs has been running for about 4 hours and still going
I have just bought an E3000 router when my old router died last week. I am having two problems:
1. The data rate slows down after a period of time (long message trail elsewhere)
2. I cannot see everything on the network.
I have several Win 7 computers, two win xp computers, three NAS devices (linux based), and a printer sitting on the network, along with two switches to cope with all the traffic (not to mention iPods, iphones etc.)With my old router, I couold see everything plugged into the network from my main Win 7 computer. (note: the win 7 network map does not always work, but the windows explorer window of the network always showed everything).With the E3000 router, I can only see 1 or 2 of the devices on the network. If I reboot the router, then sometimes all of the devices appear on the windows explorer window (sometimes not)I am running a workgroup (not a domain) and i am not using win 7's homegroup because that will not work with the non-win 7 devices.Is there a setting that will see all of the devices in Win 7 (either on the router or on the computers). I suspect it is a router issue as it worked with my old Zyxel router.
Which Intel network cards runs well with E4200 (latest FW)? I mean good connection and transfers rate. I have two clients with the same cards (Intel 4965agn, latest driver) and I got transfer rates at 144 Mbps with both radios working (2.4 and 5GHZ on the E4200). When I try to use 5Ghz only it drops to 54 Mbps and for 2.4Ghz it drops for 130 Mbps. Could I reach better transfers rate with a Intel 4965agn card (300 or 450 Mbps)?
I have 3 Wireless Devices connected to my Router which is a Ipad, Ipod Touch & laptop.I have 2 hard Wired conneted to my Router which is a ps3 and a Desktop. How can i have great speeds and reliable connection on all of them.
I have opened my NAT for xbox using Port Triggering , but I cannot open my NAT for the PC because it uses no ports!I cannot host a match using any MMO game , and I cannot host any MW3/Black Ops matches too!
Setting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password).
I purchased E1200 and have a problem. I have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.
I have a Panasonic Visio tv, I have a LINKsys E1200 that is connected to my Cable Internet. I have successfully connected the wireless to my laptop and have a guest network that has been tested and works as well. I bought a Sharp Blu Ray player that has wireless capability connected to the TV with HDMI cable and the LAN adapter is in the player. When I had the Blu Ray downstairs I had it connected to the LINKsys thru an ethernet cable and didn't use the adapter, but I wanted to take it upstairs and use it on that TV. CANNOT establish an internet connection?
