Setting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password).
View 9 RepliesI have a Panasonic Visio tv, I have a LINKsys E1200 that is connected to my Cable Internet. I have successfully connected the wireless to my laptop and have a guest network that has been tested and works as well. I bought a Sharp Blu Ray player that has wireless capability connected to the TV with HDMI cable and the LAN adapter is in the player. When I had the Blu Ray downstairs I had it connected to the LINKsys thru an ethernet cable and didn't use the adapter, but I wanted to take it upstairs and use it on that TV. CANNOT establish an internet connection?
View 2 Replies View RelatedI replaced my broken modem with a new Motorola 3360 as recommended by my ISP. The new modem works fine connected directly to my PC. When connecting the modem to the Cisco E1200 router, the same one I had with the older modem, the E1200 says I'm not connected to the PC. I've triple checked the wired connections from the modem to the router and then to the PC. I've swapped out cables and verified that they all work when used directly from the modem to the PC. I'm thinking some settings from the old Westell modem are messing with the connectivity of the new E1200 router.
View 2 Replies View RelatedI just installed an E1200 router and used the CD to take care of the software work. I Cannot connect to it by WiFi. I still have to use a cable connection.
View 4 Replies View RelatedIn one area of the home is a century link pk 5000 modem that connect to the internet. In another area of the home is the computer that has an e1200. Is it possible to connect the computer to the internet, wirelessly, from the e1200 to the pk5000? How is this accomplished?
I know the settings for the pk5000 and would "input" them into the e1200 if I friggen knew where to do this.
We have just installed the E1200 wireless router. We are able to access the internet from our home computers, however we cannot get the IPAD connected. When we try to find our wireless network to connect to it doesn't display yet our we can still see our neighbors wireless networks.
View 1 Replies View RelatedI just bough Linksys E1200, downloaded setup software, ran it, all setup went fine, no errors, but at the end I got the screen saying that can establish internet connection.The steps are totally simple. Did exactly as instructed.'Modem, connected to a PC directly give internet no problem.Modem, connected to the router, and router connected to PC - no internet.And... It's all wired at this moment, all connected with network cable.
View 9 Replies View RelatedI received the Linksys E1200 today and I installed it according to the instructions but at the end of the installation it showed the message "No internet connection." I restarted the router + modem but that didn't work at all
View 4 Replies View RelatedWhen I first set up my router, I used the same user name and pw as I had for my old router and my iPhone connect just fine. I decided to use the guest network after one of my sons friends was sitting outside one morning using my network. I told the friend the pw for the guest and changed the pw for my network and created an key on a thumb drive. Now I cannot connect my iphone. When I try to use guest is seems to work ok, but I want to use my network. I chose my network on my iphone and it simply says unable to connect. That is the only info/choice I am given.
View 1 Replies View RelatedI can connect to the wireless network, but cannot connect to the internet. The guest can connect but not the main user.E1200..Win7SP1.
View 1 Replies View RelatedLinksys E1200. I cannot connect to the Internet through my primary connection, but I can still connect through the guest connection. I think I know what happened, but I don’t know how to fix it. A connect / disconnect key on my keyboard is located right next to the mute sound key. I wanted to mute my sound, and when it didn’t mute I pressed the key a couple more times before I realized I was pressing the wrong key. So I’m guessing I probably messed up some settings. But I don’t know if on the computer, router, or both. Per the documentation I thought I might be able to fix it with Cisco Connect, but it wasn’t installed on my computer. There were only 3 Cisco modules installed.. EAP-FAST module, LEAP module, and PEAP module. I managed to find Cisco Connect on the website and downloaded it, but still couldn’t fix the problem.
View 2 Replies View RelatedI just upgraded my router from an old wireless54G to an E1200.The wireless device I have on my Sony Viao PCG GRT-240G laptop is LAN-Express AS IEEE 802.11g miniPCI Adapter
-Initially I couldn't connect at all with this machine (however the other two newer laptops could) so I contacted the Linksys tech and he advised I should upgrade my laptop driver
-After much research about this I found a common fix was to upgraded drivers from the 2004 sony driver to atheros_wifi_9.2.0.480 drivers.
-After I did the upgrade I can connect to the router on the guest account and use the internet
However, on the Main account I can connect to the router but I have no internet connectionGoogle chrome gives error belowThe server at [url]... can't be found, because the DNS lookup failed. DNS is the network service that translates a website's name to its Internet address. This error is most often caused by having no connection to the Internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing Google Chrome from accessing the network.How can I use one part of the network but not the other part? Shouldn't both the guest & main accounts use DNS lookup?
I basically plugged it into my Verizon Fios router and downloaded the Cisco Connect application (since I have a macbook air which has no CD drive)
It sets up fine, I change my router name.... BUT at the end it says there is an issue of some sort. The Cisco Connect application reloads saying "repairing connection" but then does not repair it.
Not sure where to go from here. I also logged in to 192.168.1.1 but of course I do not know where to go from here. I also reset the router trying to start from new, but no dice.
I have two E1200 routers, one of which I purchased last night. My table and netbook are only connecting wirelessly at 65Mbps max. These same devices connect to a WRT120N router at 150Mbps though.
I have the settings on the E1200 the same as the WRT120N.
So why is the the E1200 only connecting at 65Mbps then? Changing channels and MTU and beacons has no positive effect.
I have a Cisco E1200, I am wanting it to connect to the net using Etisalat ISP. The computer will talk to the router and all the settings look correct but it will not connect to the internet.The router did a software upgrade that it deemed successful.
View 9 Replies View RelatedTrying to set up E1200. I have a DSL connection, no Ethernet connection. I do have internet access. Cannot figure out how to connect.
View 2 Replies View RelatedI don't want to allow any Guest access to my network, but I do want to connect my iPad to my network. I've successfully added another computer to the network but the router setup seems to want the iPad to connect only as a Guest .Is there a way to treat my iPad as another computer (not as Guest) so that it my network recognizes it in the same way it recognizes the second computer (without entering a password)?
View 1 Replies View RelatedRan CiscoConnect.E1200.1.4.12263.1.exe on laptop twice and returned the same "there is a problem result." Disconnected router power for a few minutes in between. Current version is 1.4.11200.0. My desktop is also connected by cable to my broadbandcable modem
View 2 Replies View RelatedI want to use cisco connect with the Router E1200. There is a wireless connection between laptop and E1200 Router. When I run the "Cisco Connect" after couple minutes searching It can not find the Router and I have to put an (Router name SSID) and password.
View 9 Replies View RelatedI am trying to set up my E1200 router to Frontier FIOS internet. I went thru the setup and it failed to connect to the internet. What settings do I need? Frontier says that it should find the connection automatically.
View 1 Replies View RelatedI had originally set up my E1200 Jan 2012 & had Cisco Connect setup. I didn't use it much but back in Oct after being away for 10 days I didn't have internet connection. Had to re-set both cable modem--then I at least had connection via ethernet, but still no wifi connection. Had to turn off for awhile to get it Router to properly reset & work. & then I think I had to do another reset maybe in Dec, can't remember exactly.
As I mention in another post, I have been having frequent intermittent not connected to internet messages for a long time. Usually if I just turn wifi off & then turn it back on it finds my network (although frequently I notice that it was on my guest network rather than main). I still don't know if it is cable modem, router or my ISP, altho they came out & checked & said signals ok, but modem could be going (Its old but about to move so don't want to buy new modem now).
I updated to Mountain Lion about 2-3 weeks ago.After a Panic last night I was advised to make sure everything updated including router firmware.When I opened Cisco Connect it said I had an unsupported Operating System. Trying to figure this all out, I finally found links to download Cisco Connect that are supposed to be compatible w Mountain Lion (at least the original link said that, but not where I went w the links so hoping it is right link for that). Anyway I downloaded it & was reading a bit & then clicket on the setup icon.
That said it was damaged & to eject it. I downloaded it via wifi just like I download other software. Maybe it is hyper sensitive so I need to take it over to plug directly into my cable modem? But then that will mess up the router, although I guess it will need to be reset any way.So I think i need to get Cisco Connect updated so it works w Mountain Lion. Mountain Lion told me about 1 software that wasn't compatible but didn't pick up on Cisco Connect.So don't know if I need to do a hard wired download, unlike the way I download other things, or what to get an undamaged copy. I then hope that it will see the old version, even though it isn't didn't work & hopefully pick up all my settings & all.
& then I guess I still need to check for a firmware update. & I understand that a firmware update should be done w a good connection (although the user manual just says good signal, web says hard wired ethernet. & because of the intermittent issues I plan to to it manually by 1st downloading & then installing from the download so there won't be a risk of interruption during install--if its even needed.
I have an E1200 and if a device - such as my tablet or laptop - is left unused for a period of time - say for 4 or 5 hours - they won't reconnect to the router unless I do a power cycle/reset on the router.
View 5 Replies View RelatedI have just installed the E1200 router to my cable internet and it works great, but my printer is not wireless and is not even being recognized as an device on my computer. How do I now connect my printer?
View 1 Replies View RelatedI am connected to the internet fine, but there are some websites that when I try to navigate to them, it just loads forever (White page) [URL] I Also, some download links don't work (Flash, or Skype)I have a DSL connection with a modem and a Linksys E1200 router and I am hooked into the router via Ethernet cable. I have no antivirus software installed and windows firewall is disabled The other computer on the network and my wireless device can access all websites just fine, and even when I plug my pc directly into the modem it. I have already checked to see if the websites are having issues; they are not. I have reset my router and set it up again multiple times, I have re-installed my drivers, I even reformatted my computer (it needed it anyway..)I first assumed it was an issue with the DNS, I currently have it automatically assign a DNS and I tried using Googles DNS but the issue remained.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Sylvester
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code].....
I just purchases a Linksys E1200 router and set it up using a Dell Win 7 laptop. It works fine for the Win 7 laptop, but I am unable to connect with my Inspiron 1525 with Vista 32 bit OS. Actually, it says I'm connected, but the Access is 'Local' instead of 'Internet' - and I don't have Internet service.
After working with Linksys support, they recommended that I contact Dell. I have tried to find an updated driver for the Dell Wireless 1395 WLAM Mini Card, but am having trouble locating it on the Dell website.
I am having trouble connecting via wireless a Kodak ESP 5250 to a Linksys E1200 Router.I am using the printer console controls to configure the printer.I have verified that the password string is correct.I have changed the Channel to 6 and the encryption method to WPA/WPA2 Personal.The printer is configured to use DHCP to obtain and IP address.The problem that I am experiencing is that the printer is not getting far enough in the connection process to attempt to obtain an IP address.Tis printer was previously connected to a Belkin Router using WPA/WPA2 TKIP. But the Linksys router does not support selecting TKIP.I am not to the point that I can connect a computer (via wireless) to the printer. I have a computer connected via USB cable and that works well.
View 1 Replies View RelatedInternet went out for 3 days straight and calling frontier about 20 times they finally gave us a new model 7500 modem to replace the previous. The linksys e1200 router which had worked perfectly fine before the new modem has decided to not allow me to connect online. Sometimes it says im connected to internet but web browser does not connect, sometimes it says no internet access. I have no idea what i am doing so im not sure if it is a modem or router issue. I have done full reboots of both and powered on correctly. plugging in the modem into ports 1-3 do not light up the modems ports lights, only port 4 seems to light up when plugged in however computers light up all the ports when hard wired to E1 - E4.i also downloaded the latest firmware update for the linksys e1200 router.All fire walls are shut off and no WEP ( we live in middle of nowhere so a key is not needed )
View 7 Replies View RelatedI have a Linksys E1200 wireless router and I am having problems connecting to the internet. I can connect when plugged in to the cable modem directly. I can connect to the wireless network, but there is no internet connection. I ran ipconfig release and renew. I think it may be a DNS problem, but I'm not sure.
View 7 Replies View RelatedI have 3 Wireless Devices connected to my Router which is a Ipad, Ipod Touch & laptop.I have 2 hard Wired conneted to my Router which is a ps3 and a Desktop. How can i have great speeds and reliable connection on all of them.
View 9 Replies View RelatedI have opened my NAT for xbox using Port Triggering , but I cannot open my NAT for the PC because it uses no ports!I cannot host a match using any MMO game , and I cannot host any MW3/Black Ops matches too!
View 7 Replies View RelatedI purchased E1200 and have a problem. I have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.
View 4 Replies View RelatedIs it possible to use a Linksys E1200 as a repeater? If so, how do I set it up?
View 3 Replies View RelatedBought a new Samsung tablet and a Cisco wi fi router. But I don't have the CD drive to activate the wi fi router. I am using the Cisco linksys E1200.
View 1 Replies View Related