I have two E1200 routers, one of which I purchased last night. My table and netbook are only connecting wirelessly at 65Mbps max. These same devices connect to a WRT120N router at 150Mbps though.
I have the settings on the E1200 the same as the WRT120N.
So why is the the E1200 only connecting at 65Mbps then? Changing channels and MTU and beacons has no positive effect.
I just installed an E1200 router and used the CD to take care of the software work. I Cannot connect to it by WiFi. I still have to use a cable connection.
View 4 Replies View RelatedCan the e1200 be bridges wirelessly? Or does it have to hardwired?
View 7 Replies View RelatedJust got my E4200, setup and working with my laptop, But its only showing a speed of 65Mbps, How to get it up to the advertised 300Mbps?
View 6 Replies View RelatedSetting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password).
View 9 Replies View RelatedI have a Panasonic Visio tv, I have a LINKsys E1200 that is connected to my Cable Internet. I have successfully connected the wireless to my laptop and have a guest network that has been tested and works as well. I bought a Sharp Blu Ray player that has wireless capability connected to the TV with HDMI cable and the LAN adapter is in the player. When I had the Blu Ray downstairs I had it connected to the LINKsys thru an ethernet cable and didn't use the adapter, but I wanted to take it upstairs and use it on that TV. CANNOT establish an internet connection?
View 2 Replies View RelatedI replaced my broken modem with a new Motorola 3360 as recommended by my ISP. The new modem works fine connected directly to my PC. When connecting the modem to the Cisco E1200 router, the same one I had with the older modem, the E1200 says I'm not connected to the PC. I've triple checked the wired connections from the modem to the router and then to the PC. I've swapped out cables and verified that they all work when used directly from the modem to the PC. I'm thinking some settings from the old Westell modem are messing with the connectivity of the new E1200 router.
View 2 Replies View RelatedI have a WRT54G2 router with a desktop wired to it. The desktop is mine and my roommate wirelessly connects with her laptop and has been doing so no problem for about 6 months (ever since we got the router). On Christmas Eve, she was connected, went out, came home and found she'd lost her wireless connection. Now she can't get it back.I can still get online on the desktop.i've power cycled to no avail. What is weird is sometimes she will click on the list of available networks (so she can choose which she wants to connect to) and mine WILL be there, other times it will NOT. If she does happen to catch it at a moment when my network is there, and she tries to connect using the passphrase, it says "Trying to connect" or something to that effect, for like 3 minutes and then nothing happens. Also, not that I would need to, but if I go to "connect to" on my PC (as if I were looking to choose a network to connect to), my network name doesn't always show. It is random. Sometimes it does not even show when I go to "Networks" on my desktop.
View 9 Replies View RelatedIn one area of the home is a century link pk 5000 modem that connect to the internet. In another area of the home is the computer that has an e1200. Is it possible to connect the computer to the internet, wirelessly, from the e1200 to the pk5000? How is this accomplished?
I know the settings for the pk5000 and would "input" them into the e1200 if I friggen knew where to do this.
We have just installed the E1200 wireless router. We are able to access the internet from our home computers, however we cannot get the IPAD connected. When we try to find our wireless network to connect to it doesn't display yet our we can still see our neighbors wireless networks.
View 1 Replies View RelatedI just bough Linksys E1200, downloaded setup software, ran it, all setup went fine, no errors, but at the end I got the screen saying that can establish internet connection.The steps are totally simple. Did exactly as instructed.'Modem, connected to a PC directly give internet no problem.Modem, connected to the router, and router connected to PC - no internet.And... It's all wired at this moment, all connected with network cable.
View 9 Replies View RelatedI received the Linksys E1200 today and I installed it according to the instructions but at the end of the installation it showed the message "No internet connection." I restarted the router + modem but that didn't work at all
View 4 Replies View RelatedWhen I first set up my router, I used the same user name and pw as I had for my old router and my iPhone connect just fine. I decided to use the guest network after one of my sons friends was sitting outside one morning using my network. I told the friend the pw for the guest and changed the pw for my network and created an key on a thumb drive. Now I cannot connect my iphone. When I try to use guest is seems to work ok, but I want to use my network. I chose my network on my iphone and it simply says unable to connect. That is the only info/choice I am given.
View 1 Replies View RelatedI can connect to the wireless network, but cannot connect to the internet. The guest can connect but not the main user.E1200..Win7SP1.
View 1 Replies View RelatedLinksys E1200. I cannot connect to the Internet through my primary connection, but I can still connect through the guest connection. I think I know what happened, but I don’t know how to fix it. A connect / disconnect key on my keyboard is located right next to the mute sound key. I wanted to mute my sound, and when it didn’t mute I pressed the key a couple more times before I realized I was pressing the wrong key. So I’m guessing I probably messed up some settings. But I don’t know if on the computer, router, or both. Per the documentation I thought I might be able to fix it with Cisco Connect, but it wasn’t installed on my computer. There were only 3 Cisco modules installed.. EAP-FAST module, LEAP module, and PEAP module. I managed to find Cisco Connect on the website and downloaded it, but still couldn’t fix the problem.
View 2 Replies View RelatedIm running a linksys wireless router, WRT54G V6 with firmware 1.02.8. It worked before I moved after I moved I can't connect via wireless. hard line works. i've tried resting to factor, i've tried not using ses, not using custom ssid. I've rest it like 5 times retarted the computers. I've hit the little cisco systems button on the front, this makes it work for a few minutes. When I hit the button it will go out then come back on white, and blink around 1-2 blinks per second, it will do this for maybe 1-2min. then stops and changes back to orange. and i get nothing from it. the WLAN light is on like it's working but I cannot detect it with my desktop or laptop, can i can detect 3 other routers around me. I've tried pretty much everything i know to do, tried flashing it, updating, about the only option i have left is throwing it out the window.
View 2 Replies View RelatedI'm using E4200 with latest 1.0.02 firmware and found I can not connect to VPN with my iPhone4 by WiFi.Googled a bit and found it's a common problem for Cisco routers when wireless devices can not connect to VPN but wired ones connects with no problems.\
View 3 Replies View RelatedI have a linksys WRT54GH wireless router running firmware v1.0.01 build 001.It's setup with DHCP.My desktop computer is connected to the router via cable.I also access the connection using my laptop, via wireless.The problem is that after I start using the desktop (wired connection), I can't connect from the laptop using wireless. It happens every time. I then turn the router off and back on again. After this procedure I can successfully connect from both the desktop (wired) and laptop (wireless).
View 6 Replies View RelatedA couple nights ago, my wireless router (Linksys BEFW11S4 ver4) just stopped letting me connect to the internet. All the lights were still flashing as they should, I could still go to the setup page, I just could not connect to the internet, both through wired and wireless. I could connect straight through the modem though.
So I decided that since the router was probably over a decade old that maybe it was just its time, and I bought a new one (E1000). I connected it, and still could not connect to the internet. I then did some internet searching and found this [URL] and I followed what was mentioned in post 10 (MAC address clone and changing local IP). Now I can connect through the wired connection and I rejoiced thinking I solved it.
Then I checked my laptop and it won't even connect to the router. It sees the router, but when I ask it to connect, it just says it can't. I decided I was too exhausted to try searching and fixing it on my own and if I tried I'd just end up breaking something out of frustration.
Does the EA4500 offer b/g wireless or not. My wireless camera is b. Cannot get it to connect to the ea4500 wirelessly.
View 1 Replies View RelatedI have a WRT160NV2 connected to Internet through cable and wanted to connect it wirelessly to a WRT120N that is far from it in order to expand its signal. Is it possible to do it wirelessly or the only solution is to connect them with cable?
View 1 Replies View RelatedI have a hard wired connection thought my cable modem, but can not get it thought my WRT160N v2
View 2 Replies View RelatedI currently have an E1000 connected to my cable modem in my living room. It provides wireless access to my whole household.
I have a set of computers I want to have set up as a lab on their own router and have a WRT54GS available for me to modify.
The WRT is in the dining room (office) and the cable modem/E1000 are about 45 feet away.
I want to set up the wireless environment on the E1000 as 192.168.1.1-24 and the wired network as 192.168.2.1-24 with the wired network being able to wirelessly connect to the wired so all the machines in the house can see my server and other machines.
I need to hook two wireless routers togetner. I want to use the E4200 as the primary and the WRT54GS as a bridge or 2nd access point to the same network. I have the WRT54GS firmware upgraded to the latest dd-WRT firmware with WDS enabled.
View 1 Replies View RelatedI can not get this to work.I have 1 EuroDocsis modem and 2x 1130AG wireless things.How do I manage to get this connected to each other wirelessly?The internet is allready configured at the EuroDocsis modem and I now want to distribute it wirelessly to both 1130AG's. The EuroDocsis is using WPA2 PSK.
View 3 Replies View RelatedI just upgraded my router from an old wireless54G to an E1200.The wireless device I have on my Sony Viao PCG GRT-240G laptop is LAN-Express AS IEEE 802.11g miniPCI Adapter
-Initially I couldn't connect at all with this machine (however the other two newer laptops could) so I contacted the Linksys tech and he advised I should upgrade my laptop driver
-After much research about this I found a common fix was to upgraded drivers from the 2004 sony driver to atheros_wifi_9.2.0.480 drivers.
-After I did the upgrade I can connect to the router on the guest account and use the internet
However, on the Main account I can connect to the router but I have no internet connectionGoogle chrome gives error belowThe server at [url]... can't be found, because the DNS lookup failed. DNS is the network service that translates a website's name to its Internet address. This error is most often caused by having no connection to the Internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing Google Chrome from accessing the network.How can I use one part of the network but not the other part? Shouldn't both the guest & main accounts use DNS lookup?
I basically plugged it into my Verizon Fios router and downloaded the Cisco Connect application (since I have a macbook air which has no CD drive)
It sets up fine, I change my router name.... BUT at the end it says there is an issue of some sort. The Cisco Connect application reloads saying "repairing connection" but then does not repair it.
Not sure where to go from here. I also logged in to 192.168.1.1 but of course I do not know where to go from here. I also reset the router trying to start from new, but no dice.
I have a Cisco E1200, I am wanting it to connect to the net using Etisalat ISP. The computer will talk to the router and all the settings look correct but it will not connect to the internet.The router did a software upgrade that it deemed successful.
View 9 Replies View RelatedTrying to set up E1200. I have a DSL connection, no Ethernet connection. I do have internet access. Cannot figure out how to connect.
View 2 Replies View RelatedI don't want to allow any Guest access to my network, but I do want to connect my iPad to my network. I've successfully added another computer to the network but the router setup seems to want the iPad to connect only as a Guest .Is there a way to treat my iPad as another computer (not as Guest) so that it my network recognizes it in the same way it recognizes the second computer (without entering a password)?
View 1 Replies View RelatedI just installed an E3200 to replace my old Linksys. All my Nooks, IPADs, laptops and desktops are connecting wirelessly fine. However, I have 2 Wi Fi Radios that will pick up the network but will not connect and go into a network connect time out. One of the radios also has a hardwired connection and that is working fine. I have checked and double checked the network name, WPA key, etc. Of course I have reset all the radios and reenter new data many times, both manually and auto.
View 3 Replies View Relatedrecently tried to connect a Samsung BD-EM57C blu-ray player to my wireless network. I have a D-Link WBR-1310. Have one desktop, Smart tv currently on network --no problems. Blu ray will find my network but cannot connect. "unable to connect enter ip address manually" which I did. Fail. "enter subnet mask" which I did. Fail. "Ip address taken enter different address" Now what?
View 2 Replies View RelatedI have a WRT610 and am unable to connect any devices wirelessly. All the lights on the right hand side of the router are on except for the USB connection....what am I doing wrong? The router has worked for about a year flawlessly and last night all wireless connections quit.
View 9 Replies View Related