If I send video file(overall bit rate is 17.5Mbps) to client with 2.4Ghz band, it always freezes and go repeatedly around 1 second interval. the distance around 10m away without any wall, open space actually.
But same condition with above, cheaper wireless router no problem at all. It happens only with EA4500. And there are no any parameters setting menu actually.
I have been disappointed by the range of the EA4500 compared to previous routers, but I am most puzzled by it's behavior. I may get an "excellent" connection close to the router (one room away) and speeds up to 65 Mps, but after a few minutes of surfing the web the signal strength and speed can drop substantially.
The problem is the worst at a distance (one floor down in our house, maybe 30 feet away in total) where the signal strength may start at "good" and a speed of perhaps 30 Mps, but then after 3-4 minutes drops to "poor" and maybe 5 Mps.
Just installed a refurb EA4500 this past weekend after testing it for a week. The regular wireless network is very stable, but not much faster than my single-band DLink DIR655. Guest network seems to drop out from two connected iPhones, and when the connection drops, you have to re-login and type in the guest password everytime. The linksys firmware is up-to-date( Linksys smart wifi)and so are the iOS on the 2 iPhones. Just to add, on my old DLink, the guest network comes up secured also, so when you type in the passcode, it remembers it next it comes in range unlike the Cisco, which requires login at a web interface.
View 3 Replies View RelatedI really want to have a password on my wifi, but I cant control it when all it keeps asking me is for a CD I have a EA4500
View 1 Replies View RelatedI ran the upgrade program this morning to upgrade my EA4500 to use the cloud based software. The router is back online and everything appears ok but the program is still running and the progress is sitting at 95%. It's been like this for the past 15 minutes.
View 2 Replies View RelatedI just purchased a Linksys EA4500 (firmware is up to date). However while it set itself up wonderfully. I cannot get my wireless devices (specifically my apple tv) to see my NAS or my itunes PC, My ipads can access the NAS if i put in the correct address but not automatically.
Everything is connected to my cisco switch that is hardwired (2 xboxes, 2 ps3, 3 tv's, Wii, network audio receiver, 2 NAS, printer, 2 computers, etc). I disabled the Wi-Fi on the bell router. On the wifi are a few ipads, 3 blackberries, 1 iphone, 2 laptops).I am fully aware that the reason the wireless devices cannot see the hardwired equipment is because it is on a different subnet.
However when i try and change the IP address of the router to 192.168.2.2 (putting it on the same subnet) the router must detect a conflict then changes itself to a class A address (10.x.x.x) OR i get an INVALID IP address. As well i have noticed an overall degradation in the speed of my network (all gigabit hardware with cat 6 cabling)
My two devices access the 2.4 ghz wireless network fine on my EA4500.Both my devices, laptop and iPhone4, have N rated network cards. What do I need to use the 5.0 ghz wireless network on the EA4500?Can the iPhone4 use a 5.0 wireless network? When I try to add the 5.0 ghz Wi-Fi to my iPhone4, it cannot find the named but hidden SSID network??
View 2 Replies View RelatedSo I went out and bought a brand new EA4500, because I thought my old router was bad due to horrific wifi Speeds on my Wireless devices like my laptop and Samsung Galaxy S3. Well now I have the same issue with this new router.My speed from comcast straight from the modem is 25mbps down and 5mbps up, on the routers through a wired connection I get the same thing. As soon as a switch over to Wireless my connection goes from 25mpbs/5mpbs to less then 2mbps down. I've reduced the MTU, and I've tried turning off QoS. Nothing seems to work
View 9 Replies View RelatedMy new EA4500 works fine all day, both wireless and wifi, on both bands, but nearly every evening, the wifi signal disappears, as shown on a wifi app for my smart phone, but not on Issid on my laptop, strangely, and my PC laptop and iPad both disconnect, then reconnect. Smart phone disconnects too. It isn't like the signal drops in strength, it just goes away! I have tried various settings on modes, and bandwidths, I am using different SSID's on each band, WPA2 security with a long non-dictionary passphrase and MAC filtering. The hardwire connection works great at 30+ Mbps even when the wifi is disappearing from the wifi scanner and the wifi connections are dropping. In other words, the cable connection/modem is working fine, but the wifi radio signal stops or the SSID drops off the signal. I really can't tell, but I know it is becoming very frustrating. The old WRT54GS works fine if I put it back on-line in the evening when these things start to happen.
I have turned off everything I can think of in the house that transmits or might transmit, in case it is an interference thing. I have tried disabling the 5 GHz side, since I can't see what is happening on that band, and the last thing I tried was changing the MTU from 1500 to 1400. So far, the past evening, it was okay, but I am not confident it will stay that way.
I am trying long distance to set up above router. Router communicates fine with laptop and wifi printer but when she tries to connect her iphone (I think iphone4), phone states that password is incorrect. She is using the same password that she used for the printer and laptop which is the router default one which is a series of mixed numbers and letters.
View 1 Replies View RelatedI just purchased a Linksys EA 4500.I set up the wifi properly, with laptops, tablets, smartphones and printer. The wifi network worked fine for a couple of days.But now one of the laptop "refuses" to see the Linksys wifi network. The other devices are still connected and running regularly.
The notebook that does not connect anymore is an ACER 5740DG with an Atheros Network adapter and Windows 7 installed. This notebook is otherwise running fine.At the beginning it was connecting ok and we never had any problem at all with the previous router Belkin_N+_7991AC, that I changed just for speed.
Now the Linksys network is simply not visible to such notebook in the "Available Connections List" that I get clicking on the WiFi icon in the bottom right, while a number of other wifi networks (not mine) are clearly visible. Of course I restarted the notebook properly. For one time I got the visibility of the Linksys, I entered the password and then it was not possible to see the network anymore.No error message from Smart WiFi software.
Last Sunday, I put lots of music files into usb storage, a external harddrive linked to EA4500. which is WD element 3T.Last Wednesday, I re-organize file folders. And then yesterday(Friday), I found all my files were lost.
View 1 Replies View RelatedI own a ea4500 wireless router, I have tested the speed at speedtest.net and wirelessly I get around 9 mbps. My speed is 23 mbps when I hard wired the pc. I have check the speed on a tablet ( android ), pc and a mac to about 5 feet away from the router with no walls or anything between the two devices.I have checked all the settings but I don't see anything wrong, I have changed to N mode only to make sure I use top speed.All my devices are able to use N.
View 3 Replies View RelatedI recently bought the top end ea4500 hoping its "high end" claims would get a better wifi signal in my bedroom(on my iphone 4s) than what i was getting with my WRT54G.The end result is it constantly drops signal completely or shows my network but when I try to connect says "cannot connect to wireless network" even though it's staring me right in the face. When I hook my WRT54G up, I get a signal.. all be it weak, but at least it doesn't drop out on me.Did I just waste almost $200 on a high end router that can't push a signal out stronger than my almost 7 year old WRT54G? or am i missing some setting that will make this EA4500 worth its claims? settings info:everything is pretty much on "default" aside from the SSIDs for the different bands and the corresponding WPA passwords.
also another problem, it seems like the router itself craps out every 60-120 minutes, no leds lit up on the router and my modem (Cisco DCP3010) shows no "link". Yet when hooked directly to the PC there is a "link", so pretty sure its the router and not the modem.
I use the Smart Wi-Fi app on my iPad3 (IOS 6.1.3) to access my EA4500 remotely.When I want to add a port forwarding, it shows always 192.168 as start of the ip address related to the ports. But I have a 10.71 network installed and cannot change the 192.168 to 10.71. I suppose this is a bug.
View 2 Replies View RelatedI just purchased the EA4500 router and went through the setup with no issues. The only problem is I cannot access the router either locally or through the Smart Wifi dashboard. Everytime I go to the page with "Access Router", enter the password and clikc the "Submit" button it does nothing...no incorrect password prompt or idle prompt...almost like the page is broken somehow. I've done all of the usual, restart router, restart PC, restart cable modem, etc. and always having the same result.
View 4 Replies View RelatedI am backing up massive amounts of data to the cloud. Everytime I do this, the wireless performance on my EA4500 seems to degrade to half its throughput. I am using the 2.4 GHz band.
View 9 Replies View RelatedI purchased this Router about 2 weeks ago as a phased upgrade of our Home Network, primarily to enhance media streaming. It has the latest firmware preinstalled from the factory. Prior to the purchase and installation of the EA4500 Router I replaced my old Motorola SurfBoard SB6120 DOCSIS 3.0 Cable Modem with a Motorola SurfBoard SB6141 DOCSIS 3.0 Cable Modem. My old Linksys E2000 Router worked perfectly with the SB6141, with the exception that the E2000 wasn’t IPv6 enabled, but does have 10/100/1000Base-T Ethernet (RJ-45) and Internet ports.
The EA4500 has been installed for about 10 days and seems to have improved local network speeds and I don’t seem to be having any Internet connectivity issues. However, there are some disturbing issues with the EA4500 and the AE3000 I purchased. There are 11 devices connected through the Router; a Dell Desktop (wireless with the AE3000), a Dell Desktop (Ethernet), a Dell Laptop (wireless), 2 Canon Printers (1 Ethernet and 1 Wireless), 2 Western Digital 1TB MyBookLive Network Drives (both Ethernet), a WD TV Live Streaming Media Player (wireless), an Apple TV media player (wireless), an iPad (wireless), and an Android Smartphone (wireless).
Issue 1 – The Linksys Smart Wi-Fi interface appears to be unreliable at times!!! I’ve read about this problem here on the Community involving the EA6500, so I don’t know if this is a Linksys Server issue, as suggested in a few responses, or a bug in the Router firmware, or defective hardware. However, when the interface locks up, it can’t be accessed from a wireless or wired connection. Usually, powering down the Router and then powering it back up and restart will allow it to function again. However, at times before the interface completely locks up it shows either just a white screen or the security screen will show no firewall features enabled. This is a little scary, so I’ll do a complete reset and setup; this is becoming a pain in the rear! Is there any hope for this being fixed, in this Router, not the next generation?
Issue 2 - All of my network devices show up in the Router’s Device List. Except for the Apple devices they also show up, when they are online, in Windows 7 Explorer under Network and when you click on Network they are correctly displayed as Computers, Media Devices, Network Infrastructure, or Storage. However, when you click on “Open Network and Sharing Center” and then click on “See Full Map”; it fails with the response “Windows cannot create the network map. Responses from other devices on the network are delayed or there is an incompatible router on the network”; no device map is shown. When I follow the link for more information, the only thing that stands out is “A device on the network, such as a hub or switch, is not working properly or is not compatible with the Link Layer Topology Discovery (LLTD) protocol, which Windows uses to create the map. To fix this problem, disable the device, turn it off, or remove it from your network”. All of my network devices showed up on the Network Map with the old E2000. This issue is the same on all of my computers, either wired or wireless.
I’m having with the EA4500 and the AE3000; they are both probably going back to Amazon.
I am using a EA4500 and use Linksys Smart Wi-Fi to manage the device. In the household we have multiple Apple i devices. Somehow the Linksys Smart Wi-Fi combined two separte i devices (iPhone 5 and a 4th generation iTouch) to one user.The devices actually have different names, but the Smart Wi-Fi is combining them into one device. So I can't use Parental Controls on one of the devices.
View 8 Replies View RelatedI just setup my new Cisco EA4500 and upgraded to latest firmware and signed up for my account.Local access to the router works fine and I see the Smart Wi-Fi admin/config interface However when I try to go to the following site: url...To access Linksys Smart Wi-Fi Tools, your router <em>requires</em> the <a href="url...Series Linksys Smart Wi-Fi Firmware</a> and you will need to associate your router with your Linksys Smart Wi-Fi account.On a computer or device connected to your router, open url... and follow the instructions. This requires that you enter the router password so have that ready.
However I see no way to perform the association step - my account exists and my router is configured.I am doing all this behind this router wi-fi network not remotely.
My desktops _usually_ connect, and then the connection will drop/go slow(14400 slow)/give that little yelow triangle on top of the wifi icon.First i had an edimax wifi PCI, now i have a trendnet wifi PCI. They both do the same thing.If i connect my HTC hero and start internet sharing, it works very well, and is stable. My ethernet works fine as well. It is like my computer is immune to PCI cards?I have tried with different wifi APs now, but its still the same.I have a zyxel adsl modem, and a linksys wifi AP hooked up to that. I noticed, that when my desktop is connected, the zyxel will get some kind of overflow from the linksys. It says "client reached max number of sessions per host" It's like my desktop is killing the network. I have tried many things. Drivers, fail safe, registry cleaner(I know), killing all unnescessary program, switching the PCI ports, but none of it seems to work.
I had my laptop running connectify (access point app) and it actually worked fine, but today it won't connect to that either.I'm going to create another partition on my harddrive, and install fresh windows 7 on that, and see if it does the same. But even if it doesn't I _want_ to find out what is causing this instabillity.When i try running the network diagnostics, it says DNS error, or that the router is fail. But my laptop works fine.Also, when doing speed tests, my laptop gets normal speeds, and my desktop is VERY slow DL, but normal UL ?In speed tests my desktop is very slow, but stable, but during the test, my laptop will first go like 2 mb/s - 3mb/s DL and suddently BURST up to like 64 mb/s although i only have 10 mbit line? It's like its buffering or something. Very weird behaviour, but working fine.And no, i do not have torrent programs or whatever running.Some says that i shout try and change wifi channel and bands, and avoid "mixed" mode, but none of it works. Always the same problem.ATM. my computer can't connect to any wifi at all. It keeps having the yellow triangle.
the only way i can get 300mbps from this router is by having these settings, it seems the only valid settings to get 300mbps from the router are the following:
Network Mode: mixed
Channel Width: auto (20mhz or 40mhz)
Channel : 1
if i leave the channel to auto it won't show up as 300.on top of that it doesn't want to stay at 300mbps for very long, sometimes its max rate in inSSDer is only 144 or 156mbps. its the weirdest thing, i think this version of the firmware seems to forget to check for how fast its wireless transmit speed is.When it reboots it only transmits at 144 or 156mbps. i have to go in the basic wireless page and just save the settings to reset it to 300, i don't even have to change anything, it resets its max rated speed back up to 300mbps.and more importantly, are the devs aware of this problem for the e1200 v2 ?
I have a Cisco Linksys EA4500 router that I would like to be able to connect to the LAN network in my building. The router is currently providing internet over wifi, but I'm not able to access the LAN network. I'm using DC++ to connect to a hub in our building, and this works fine if I directly connect my computer to the wall - I can get internet and LAN access. I can also see the other computers in the 'network' section of 'computer' in windows. I can't see any of the other computers in the 'network' section if I use my router (only devices connected to my router). I would like to be able to be able to connect to the internet and the LAN network over my wireless?
View 5 Replies View RelatedI recently found that whilst using my WIRED connections, web pages have been opening slower at times. My ping times to google.com usually is around 72-84 ms which I continue to get if I hook up the cable modem directly to the PC. As soon as I utilize the Linksys router, I start getting higher ping times anywhere from 72-300 ms. Firmware version is 1.5.01 which I recently upgraded to. I tried resetting and so on. Is there an older firmware version that works better? I'm currently running Windows 7 Ultimate 64-bit.
View 1 Replies View RelatedI recently replaced my old WRT54G router with a E3200 router.
Unfortunately, ever since my wireless network is a lot more unstable than before. I very often experience serious lag spikes and drops in speed. Very often I experience serious lag for a couple of seconds after which everything returns to normal. I notice this the most in online gaming, but it is also noticeable while browsing the web. When downloading large files (e.g. steam games), the download speed also seems to suffer from this by dropping every now and then.
There are no connection drops however. And it only seems to affect the wireless network.
I have configured the E3200 router manually using the Web UI and is has been configured exactly the same as my WRT54G: i.e. only 2.4GHz band enabled with b/g/n, WPA2 security, MAC filtering on, no throtling/parental control/port forwarding, UPnP disabled. The E3200 is in the exact same place as the the WRT54G was.
Things I have done so far for troubleshooting: I used inSSIDer to monitor the wireless network and it's signal strength seems about the same as the WRT54G. I changed channels for best signal strength (there is only one other wifi network that seems to be configured as a dual channel N network; 3 other networks with very low signal strength) and have tried every channel.
I updated the fimware to the latest version (Ver.1.0.04 (Build 1)) and did a factory reset and power cycle afterwards.
I noticed that switching channels can account for 5-10Mbps differences in internet speed. Something I never noticed with the WRT54G. The lag spikes occur more often on some channels than on others. This seems not related to the speeds I get on the channel.
I really can't imagine that a router marketed as High Peformance router with superior speed and superior range is less stable than my old WRT54G router.
Is there something I can do to improve stability of this router?
I have had my EA2700 for about 6 months now. Have had no problems until about a month ago. One night I could not get the router to connect to the internet. First thoughts were that the cable connection had gone down. When I finally started to trouble shoot I was able to confirm the cable connection is fine by connecting to the modem directly.
Out of the modem I am getting 14+ Mbps. (I only Pay for 10 So a plus there)
I could not get the router to connect to the internet. I ended up resetting the router and reconfiguring it. Ever since then I have been getting really unstable connection to the internet.
When I connect directly to the modem (cabled) I am getting a nice steady connection . When I add the router and hardware in I get a good connection only a Mbps or 2 drop off and a pretty steady connection. Then when I connect over WIFI I get a much larger drop off depending on if the device is a 2.4 or a 5
The connection is extremely unstable. The curve on the graph {URL} is very peaky and has extreme highs and lows. This is multiplied when running on the GHz (as my laptop runs on). My Iphone running on GHz. I can pull down 9 Mbps but the curve is still up and down. Iphone on GHz I barely get Mbps and it is extremely choppy on the graph.
I am able to back this up with my I PAD. I can only confirm the 2.4 number with the laptop as it does not have GHz radio in it. So every thing that us running on the 2.4 is getting poor connections.
I also suspect that the through put on the wired side is poor as well. I am unable to prove it as every test I run shows a good connection but netflix has been locking up and I have to restart what ever I am watching 2 to even 10 times a show. I need to do more testing to be sure the network or the devices are to blame.
Region : Netherlands
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 121211
ISP :
after changing from a Thomson router with wifi to the TP-link WDR-4900 I find that the wifi is very unstable. The 2.4GHz is operating on the same channel as my previous router (channel 8 - which is the lest busy channel around my house), and none of my neighbours have wifi on the 5GHz band. Almost all devices in my home regularly have to reconnect to the wifi, both on the 2.4GHz as on the 5GHz (tested with more than 8 devices). Almost every 15 minutes I see a "wifi channel disconnected" message, 10 seconds later followed by a "wifi connected" message. the Wifianalyser app on my tablet confirms that the wifi signal drops once in a while to zero. I use the latest stable frmware (I read that there is beta firmware but I don't like to loose warranty). The stability seems to unrelated to the amount of traffic on the wifi network.
Will this be fixed in the next firmware of the TP-WDR-4900 ?
I have an NTFS formatted USB disk drive (Western Digital My Passport Essential Black 320 GB WDBAAA3200ABK) attached to the WRT160NL wireless router (Firmware Version 1.0.02), and I have video, picture and music files on the USB disk drive in three folders: Videos, Music, Pictures. Auto-scan is disabled, I scan the media files manually by clicking on the 'Scan All' button.
PROBLEM 1 The worst problem is that the router is very sensitive to files that can't be recognized by the router as media files. For example if there are subtitle files (*.str) between the media files, then strange and nondeterministic things happen: some valid media files are skipped and not included in the media database; some files included but the file names are mixed. The most irritating in the bug is that there is no log file, where you could find the problem, and so you never know which file cause the problem, and you have to browse through all the files hunting for the cause.
PROBLEM 2 When the router is in the process of scanning the media files, then the internet (WAN) connection often can't be used, although the router can be accessed and the status says it is connected to the internet.
i have a little annoying problem with my E4200. V1 with the latest 04 fw. It seems, that after many hours of downloading at full speed (only one torrent at a time) the speed goes down, and up again, and becoming unstable. My max download speed is 1.5 Mb/s, and it can drop from that, to 50 kb/s, and then up again. and i have no internet access when that happens, but it only last 10-20 seconds and then its back again. Sometimes i get that yellow warning sign on the taskbar which says "No Internet Access" but not always.
Seems like its happening after many hours of downloading at full speed. im on the latest firmware, have tried different channels, 20 Mhz only on Channel Width, different names on the 2.4Ghz and 5Ghz channels.. i use the 2.4Ghz channel btw. Otherwise its stable, and i have had no problems while gaming online.
I noticed some serious random ping spikes in online games and found that the connection between my Laptop and the E4200 is very very unstable. Sometimes it works perfectly fine but at other times my ping will spike each 5 seconds to three or even four digits and back to normal. I never get disconnected but playing is obviously not possible.
I ran several pingtests through pingtest.net and got everything from 15ms ping 3ms jitter to like 400 ping 300 jitter.
Eventually, I pinged the router (192.168.1.1) and got delays between 2ms and 300ms for both the 2.4 ghz and the 5ghz network. The 2.4ghz channels are fairly crowded but the signal is perfectly fine and stable. The 5ghz band is totally free therefore interference shouldn't be a problem i guess.
I assign private IP for each PC within LAN. And DHCP is in charge of wireless connection since 192.168.0.100 for 10 clients. ,Web setup access is also disable for wireless connection.When a notebook connect to WRT54G via wireless. Private IP is always out of range and it could accesses web setup.What happen to my WRT54G ?
View 3 Replies View RelatedRegion : Hongkong
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 3.14.3 Build 130320 Rel.39025n
ISP : PCCW Netvigator
I have upgraded to the latest firmware which solved lots of problems regarding unstable wifi connection as well as BitTorrent / P2P transfers.But I also observed that when my BT is on (Transmission for Mac) at around 50KB/s upload and download, my network latency hikes up from some 30ms to 500ms which affects a lot on web browsing or other apps requiring Internet.My BitTorrent app is showing I am merely making some 20 peers connection so I am not convinced that is an ISP problem but it's more about the router.
The coaxial"or any other metal cable" was using for transmission signals(before fiber optic) the coaxial need repeater every 2 or 3 Kilo meter,because the signal will be attenuation when pass through the cable,when we transmission electricity to far places ,we use transformer to rising the voltage to 10000 or 100000 volt
View 8 Replies View Related