I assign private IP for each PC within LAN. And DHCP is in charge of wireless connection since 192.168.0.100 for 10 clients. ,Web setup access is also disable for wireless connection.When a notebook connect to WRT54G via wireless. Private IP is always out of range and it could accesses web setup.What happen to my WRT54G ?
View 3 RepliesI have a WRT54G wireless router that I haven't used in years because my old cable provider supplied me with a router. I recently switched cable providers & they don't provide a wireless routers. I would like to use my WRT54G router, but I don't have the cd. I figured it wasn't a problem because I can just do a manual setup using the ip address 192.168.1.1. I receive the pop up window to enter the user name & password. I follow the instructions & just type in the password field the word admin & l left the user name blank but it doesn't work.
View 4 Replies View RelatedI had my router settings in a file on my hard drive so I would not lose them. Just my luck, my hard drive took a giant dump and the restore did not restore 100% and guess which file was among the missing?So I've followed about 15 different "reset" instructions which includes holding the reset button for 10-60 seconds; unplugging the router afterwards for anywhere from immediate to 60 seconds. Obviously, none of those sets of "sage" advice had any influence whatsoever on my router. My "server" is of my own creation:
Core2 Quad Q9550;
8 GB PC28500;
Gigabyte GA-EP45-UD3R;
Windows 7 Ultimate 64 bit SP1.
Cable Modem RCA DCM425.
I'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
View 1 Replies View Relatedmy mother in law thought she forgot her wifi password so i tried to do a reseti reset it then no internet at all and could not access the router gateway page (192.168.1.1)I had to set the internet protocol to default and 2 power cycles later i can access the internet.Then i used the linksys disc to set up the security and now it doesn't work can't access nothing through ie.
View 1 Replies View RelatedI have a WRT54G router that I have not used for many years, but now I need to use it again. I have connected it between my modem and PC, and I am able to get an internet connection on the PC, but I am unable to connect to the router's configuration page. I have tried resetting the router numerous times (holding the reset button 5 seconds, 10 seconds, even longer) to reset the IP address to the default 192.168.1.1 address, but still cannot access the page. The power LED is on and the WLAN and Internet LEDs are on, and the LED for the port my PC is connected to is on. The hardware version of the router is v3. I tried downloading the latest firmware, but without being anble to communicate with the router at the IP address I cannot update the firmware. How can I go about connectiong to the router's setup page? When using ipconfig, the Default Gateway appears to still point to my ISP's IP address instead of the router's.
View 9 Replies View RelatedI have a Linksys Router that shows WRT54G Ver 3 on its base, but when I go in the settings I realized it says WRT54GL over there.
View 1 Replies View RelatedI have lost my installation disk for my WRT54G Version 8. Where I can download the drivers and installation.
View 9 Replies View RelatedI have wrt54gl setup with dd-wrt standard version running hotspotsystem. 3 wrt54g version 5 with dd-wrt micro setup as WDS client of wrt54gl. After the intial setup I can log into the main router wrt54gl (192.168.1.1)and all 3 WDS routers (192.168.1.2 ,3 and 4), but after couple of days of testing suddenly i can not login to 2 of the WDS routers,
I mean I can connect to it and it will get me to internet but I can no longer login, it just says the page take too long to load. I know if I do a hard reset and setup WDS again then it will work, but I dont want to keep doing that. Tried to power cycle the router but still wont work. Is it the load on the router made it inaccessible ?
I wanted to know if you can setup reserved wireless IP address on the WRT54G router. With all the kids devices, when I reset the router, getting all the devices online is a challage. Some end up with duplicate IP address causing conflicts. If I could reserve an IP address for a specific device. Let me know what option the router has?
View 3 Replies View RelatedWhen I had DSL, my WRT54G was my DHCP master for my home network. When I got AT&T U-Verse, their "gateway" became the DHCP master and also the wireless access point. But the signal was not strong enough where I wanted to use it, so I hooked up the WRT54G again. I discovered that if I connected the U-Verse gateway to the "Internet" port on the WRT54G Linksys, then my home network was split in two, which I did not want. The WRT54G access point is physically somewhat distant from my wired computer, so I wanted to keep the U-Verse gateway as the DHCP master. (The U-Verse gateway is a router with four "computer" ports but no "Internet" port.)
I followed instructions on the Linksys web site, and using my wi-fi connected computer I re-programmed the WRT54G to be "Disabled" as a DHCP server. Then I powered down and physically connected the U-Verse gateway to a "Computer" port on the WRT54G. This solved my problem: my distant wi-fi computer now has a good signal, and both computers "see" each other.
However, now I seem to have lost access to the WRT54G setup "web page." Is it possible to access the innards of the WRT54G when its DHCP service is disabled? Or would I have to reset the device to factory configuration and start all over if I wanted to make any tweaks?
When I go to the router setup screen via 192.168.1.1 the screen does not load properly in MSIE or Firefox. Text does not load.The graphics load okay, and the dropdown boxes, checkboxes, etc. Since many of the links are from text, and all of the descriptions, it is impossible to navigate properly. I managed only by using Firefox's Page Info, Links tab and cutting & pasting. A couple of screen captures are available [URL] have downloaded the latest firmware, but while I can get to the Administration page, much less click on, the Upgrade Firmware sub-tab.
View 3 Replies View RelatedI have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed." I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it.
View 9 Replies View RelatedI'm trying to setup a Linksys wireless-g router model number WRT54G with my DSL connection. I followed the basic instructions that came with the router and towards the end of the process it says detecting network settings with a % bar. The bar fills to 100% and then asks for a password. I've tried the password my DSL company gave me along with various other things like admin etc. After I enter the password I hit enter and it just asks me for the password over and over again.
View 9 Replies View Relatedhow do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
I am finally duffing my WRT 610N (N=Never consistent in performance) main router and WRT54G that I am using up in my shop as an expander. Now I am going to a E4200 Main Router and E3000 for my secondary router (Truthfully a dual band expander).
Am I going to just simply Flash my 610 to default , disconnect it and pack it away , Setup my new E4200 , Plug in my E3000 into port 1 and go about giving it a separate IP Addy? Or can I expect a **bleep**? Any setup tips?
Wirelessly I am running 2 laptops , a PS3 , Xbox 360 , Epson printer , a picture frame and Samsung Blue Ray and TV, and on occasion 2 android phones. On the Wired side (Ethernet) I have a Sling Box , a Desktop , and the router up in the shop. This is the normal load and never everything all at once (Although it has been done).
I have a WRT54G V8 and everyone says the username to sign is is blank and the password is admin. I have tried this and it does not work. I have also reset the router several times and this also does not work.
View 2 Replies View RelatedI've currently got a WRT54G and have an opportunity to buy a WRT54GS. The problem is that the seller of the WRT54GS has lost the Set-Up Wizard CD & Hard Copy Quick Installation Guide. Obviously I have these items already with my WRT54G. My question is this. Are these items different for the WRT54G or will the stuff I already have for the WRT54G "work" for the WRT54GS.
View 5 Replies View RelatedI recently found that whilst using my WIRED connections, web pages have been opening slower at times. My ping times to google.com usually is around 72-84 ms which I continue to get if I hook up the cable modem directly to the PC. As soon as I utilize the Linksys router, I start getting higher ping times anywhere from 72-300 ms. Firmware version is 1.5.01 which I recently upgraded to. I tried resetting and so on. Is there an older firmware version that works better? I'm currently running Windows 7 Ultimate 64-bit.
View 1 Replies View RelatedIf I send video file(overall bit rate is 17.5Mbps) to client with 2.4Ghz band, it always freezes and go repeatedly around 1 second interval. the distance around 10m away without any wall, open space actually.
But same condition with above, cheaper wireless router no problem at all. It happens only with EA4500. And there are no any parameters setting menu actually.
I recently replaced my old WRT54G router with a E3200 router.
Unfortunately, ever since my wireless network is a lot more unstable than before. I very often experience serious lag spikes and drops in speed. Very often I experience serious lag for a couple of seconds after which everything returns to normal. I notice this the most in online gaming, but it is also noticeable while browsing the web. When downloading large files (e.g. steam games), the download speed also seems to suffer from this by dropping every now and then.
There are no connection drops however. And it only seems to affect the wireless network.
I have configured the E3200 router manually using the Web UI and is has been configured exactly the same as my WRT54G: i.e. only 2.4GHz band enabled with b/g/n, WPA2 security, MAC filtering on, no throtling/parental control/port forwarding, UPnP disabled. The E3200 is in the exact same place as the the WRT54G was.
Things I have done so far for troubleshooting: I used inSSIDer to monitor the wireless network and it's signal strength seems about the same as the WRT54G. I changed channels for best signal strength (there is only one other wifi network that seems to be configured as a dual channel N network; 3 other networks with very low signal strength) and have tried every channel.
I updated the fimware to the latest version (Ver.1.0.04 (Build 1)) and did a factory reset and power cycle afterwards.
I noticed that switching channels can account for 5-10Mbps differences in internet speed. Something I never noticed with the WRT54G. The lag spikes occur more often on some channels than on others. This seems not related to the speeds I get on the channel.
I really can't imagine that a router marketed as High Peformance router with superior speed and superior range is less stable than my old WRT54G router.
Is there something I can do to improve stability of this router?
I have had my EA2700 for about 6 months now. Have had no problems until about a month ago. One night I could not get the router to connect to the internet. First thoughts were that the cable connection had gone down. When I finally started to trouble shoot I was able to confirm the cable connection is fine by connecting to the modem directly.
Out of the modem I am getting 14+ Mbps. (I only Pay for 10 So a plus there)
I could not get the router to connect to the internet. I ended up resetting the router and reconfiguring it. Ever since then I have been getting really unstable connection to the internet.
When I connect directly to the modem (cabled) I am getting a nice steady connection . When I add the router and hardware in I get a good connection only a Mbps or 2 drop off and a pretty steady connection. Then when I connect over WIFI I get a much larger drop off depending on if the device is a 2.4 or a 5
The connection is extremely unstable. The curve on the graph {URL} is very peaky and has extreme highs and lows. This is multiplied when running on the GHz (as my laptop runs on). My Iphone running on GHz. I can pull down 9 Mbps but the curve is still up and down. Iphone on GHz I barely get Mbps and it is extremely choppy on the graph.
I am able to back this up with my I PAD. I can only confirm the 2.4 number with the laptop as it does not have GHz radio in it. So every thing that us running on the 2.4 is getting poor connections.
I also suspect that the through put on the wired side is poor as well. I am unable to prove it as every test I run shows a good connection but netflix has been locking up and I have to restart what ever I am watching 2 to even 10 times a show. I need to do more testing to be sure the network or the devices are to blame.
Just installed a refurb EA4500 this past weekend after testing it for a week. The regular wireless network is very stable, but not much faster than my single-band DLink DIR655. Guest network seems to drop out from two connected iPhones, and when the connection drops, you have to re-login and type in the guest password everytime. The linksys firmware is up-to-date( Linksys smart wifi)and so are the iOS on the 2 iPhones. Just to add, on my old DLink, the guest network comes up secured also, so when you type in the passcode, it remembers it next it comes in range unlike the Cisco, which requires login at a web interface.
View 3 Replies View RelatedI have an NTFS formatted USB disk drive (Western Digital My Passport Essential Black 320 GB WDBAAA3200ABK) attached to the WRT160NL wireless router (Firmware Version 1.0.02), and I have video, picture and music files on the USB disk drive in three folders: Videos, Music, Pictures. Auto-scan is disabled, I scan the media files manually by clicking on the 'Scan All' button.
PROBLEM 1 The worst problem is that the router is very sensitive to files that can't be recognized by the router as media files. For example if there are subtitle files (*.str) between the media files, then strange and nondeterministic things happen: some valid media files are skipped and not included in the media database; some files included but the file names are mixed. The most irritating in the bug is that there is no log file, where you could find the problem, and so you never know which file cause the problem, and you have to browse through all the files hunting for the cause.
PROBLEM 2 When the router is in the process of scanning the media files, then the internet (WAN) connection often can't be used, although the router can be accessed and the status says it is connected to the internet.
i have a little annoying problem with my E4200. V1 with the latest 04 fw. It seems, that after many hours of downloading at full speed (only one torrent at a time) the speed goes down, and up again, and becoming unstable. My max download speed is 1.5 Mb/s, and it can drop from that, to 50 kb/s, and then up again. and i have no internet access when that happens, but it only last 10-20 seconds and then its back again. Sometimes i get that yellow warning sign on the taskbar which says "No Internet Access" but not always.
Seems like its happening after many hours of downloading at full speed. im on the latest firmware, have tried different channels, 20 Mhz only on Channel Width, different names on the 2.4Ghz and 5Ghz channels.. i use the 2.4Ghz channel btw. Otherwise its stable, and i have had no problems while gaming online.
I have a 4 year old Linksys WRT54G V8 I'd like to set up as an access point for an Xbox 360 or DirecTV box. I am using a Linksys E3000 as my wrieless router, atm, and was wondering if there was anyway to use the WRT54G as an access point before I go out and buy other network adapters to get these devices connected.
View 2 Replies View RelatedI noticed some serious random ping spikes in online games and found that the connection between my Laptop and the E4200 is very very unstable. Sometimes it works perfectly fine but at other times my ping will spike each 5 seconds to three or even four digits and back to normal. I never get disconnected but playing is obviously not possible.
I ran several pingtests through pingtest.net and got everything from 15ms ping 3ms jitter to like 400 ping 300 jitter.
Eventually, I pinged the router (192.168.1.1) and got delays between 2ms and 300ms for both the 2.4 ghz and the 5ghz network. The 2.4ghz channels are fairly crowded but the signal is perfectly fine and stable. The 5ghz band is totally free therefore interference shouldn't be a problem i guess.
I am using a Linksys Wireless-G Broadband Router(Model WRT54G). I am trying to set up a desktop computer to have a wireless usb adapter running so I can connect to the Wireless-G Broadband Router. When I run the setup CD for the wireless usb adapter it asks me to push the Wi-Fi Protected Setup Button on the Linksys Wireless-G Broadband Router.
I have looked at the Linksys router found an obscure button on the front with the Cisco Systems Copyright logo on it. I pushed this but the wireless usb adapter failed to locate the wireless network. There is also another button on the back of the Linksys Router that is a Reset button.
How to setup WRT54G in router mode
View 9 Replies View RelatedI have a Linksys WRT110 wireless router for my desktop via a D-link DWA-125 wireless adapter. The OS is Windows 7 64 bit and I mainly go online to play games. This has been a while and every time I play games, which requires stable connection, I will get this lag (the ping goes as high as 600ms for every few seconds then goes back to normal).I tried many ways to troubleshoot and find no solutions. I updated firmware for USB adapter, power cycling the router and reset the router many times.
View 3 Replies View RelatedI bought the WMP600N because Linksys and Microsoft listed it as 'compatible' for Windows 7 x64. My experience:
- unstable and weak connection
- pings to websites like google.com drops, average: 1 out of 3
- low signal, on the same spot my three years old HP-laptop with 'a build in wireless card' has full signal strength in Windows 7
- it works well under Windows XP (32 bit)
I am convinced that drivers for the WMP600N are not ready for Window 7 x64. Linksys (or Ralink, which developed the chipset), release a proper driver for the WMP600N.
wrt54g v1.1 After setting up the wireless router, I can use the internet on the pc as well as a wireless device. However after putting my pc in standby mode then back on, I can no longer connect to either. I have to restore factory defaults each time and re-enter all passwords and settings.
View 9 Replies View RelatedI have a WRT54G router V6, and I am wondering how many wireless connections it supports? Because, I have one wired connection and whenever I try to connect more than 4 wireless devices a device will get booted.
View 9 Replies View Related