my mother in law thought she forgot her wifi password so i tried to do a reseti reset it then no internet at all and could not access the router gateway page (192.168.1.1)I had to set the internet protocol to default and 2 power cycles later i can access the internet.Then i used the linksys disc to set up the security and now it doesn't work can't access nothing through ie.
View 1 RepliesRecently added a NookColor to my toys. Works fine except at home. The device shakes hands with the router but won't connect. Nook connects seamlessly with every other network I've tried. Had my Bro-in-law over with his Anfroid based mobile devices and they won't connect either. We currently are running 4 boxes (2 @ desktop and laptop) off this router with no problems.As near as I can figure the latest firmware update (2007) can't handle the Android OS protocol and while they recognize each other they won't speak or play nice.Any options y'all know of short of replacing the router with a shiny new one ?
View 5 Replies View RelatedI have a WRT54G wireless router that I haven't used in years because my old cable provider supplied me with a router. I recently switched cable providers & they don't provide a wireless routers. I would like to use my WRT54G router, but I don't have the cd. I figured it wasn't a problem because I can just do a manual setup using the ip address 192.168.1.1. I receive the pop up window to enter the user name & password. I follow the instructions & just type in the password field the word admin & l left the user name blank but it doesn't work.
View 4 Replies View RelatedI have a WRT54G router, and when I am in the security area, where you choose WPA, WEP, etc... I keep clicking the dropdown menu, and when I choose anything BUT disable, the security auto-sets back to disable. I have rebooted the router. I have rebooted the modem. I have changed my router's password.How do I turn my WEP back on without it just saying. Also, for additional notation, my US light on my modem is no longer green, it is orange since this issue has occured. Is there any connection that might be related to this?
View 8 Replies View RelatedI had my router settings in a file on my hard drive so I would not lose them. Just my luck, my hard drive took a giant dump and the restore did not restore 100% and guess which file was among the missing?So I've followed about 15 different "reset" instructions which includes holding the reset button for 10-60 seconds; unplugging the router afterwards for anywhere from immediate to 60 seconds. Obviously, none of those sets of "sage" advice had any influence whatsoever on my router. My "server" is of my own creation:
Core2 Quad Q9550;
8 GB PC28500;
Gigabyte GA-EP45-UD3R;
Windows 7 Ultimate 64 bit SP1.
Cable Modem RCA DCM425.
How do I find security code for my router. It is out of warranty and live chat will not supply it to me. Is there a default code ?
View 9 Replies View RelatedInstlling WPA2 on my router I had this router WRT54G ver 6 for several years and it works perfect only thing is I have no security on my n wireless
View 3 Replies View RelatedI'm trying to change the wireless security mode on my folks' WRT54G to see if I can get the wireless adapter on their new TIVO to talk to the router. It looks like TIVO only does WEP, not WPA. I get into the wireless page of the router and when I try selecting anything but "WPA Personal", the selected choice flips back to "WPA Personal" in less than a second. I've updated the firmware but no change.
View 9 Replies View RelatedMy WRT54G Router has been reset after severe weather conditions, the wireless in now unsecure. I am trying to change it back to secure mode under wireless / security wireless, but it does not allow me to do so. The security mode remains disabled and does not change to WEP or WPA.
View 2 Replies View RelatedI'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
View 1 Replies View RelatedI have a WRT54G router that I have not used for many years, but now I need to use it again. I have connected it between my modem and PC, and I am able to get an internet connection on the PC, but I am unable to connect to the router's configuration page. I have tried resetting the router numerous times (holding the reset button 5 seconds, 10 seconds, even longer) to reset the IP address to the default 192.168.1.1 address, but still cannot access the page. The power LED is on and the WLAN and Internet LEDs are on, and the LED for the port my PC is connected to is on. The hardware version of the router is v3. I tried downloading the latest firmware, but without being anble to communicate with the router at the IP address I cannot update the firmware. How can I go about connectiong to the router's setup page? When using ipconfig, the Default Gateway appears to still point to my ISP's IP address instead of the router's.
View 9 Replies View RelatedI have a Linksys Router that shows WRT54G Ver 3 on its base, but when I go in the settings I realized it says WRT54GL over there.
View 1 Replies View RelatedI have lost my installation disk for my WRT54G Version 8. Where I can download the drivers and installation.
View 9 Replies View RelatedI have wrt54gl setup with dd-wrt standard version running hotspotsystem. 3 wrt54g version 5 with dd-wrt micro setup as WDS client of wrt54gl. After the intial setup I can log into the main router wrt54gl (192.168.1.1)and all 3 WDS routers (192.168.1.2 ,3 and 4), but after couple of days of testing suddenly i can not login to 2 of the WDS routers,
I mean I can connect to it and it will get me to internet but I can no longer login, it just says the page take too long to load. I know if I do a hard reset and setup WDS again then it will work, but I dont want to keep doing that. Tried to power cycle the router but still wont work. Is it the load on the router made it inaccessible ?
I wanted to know if you can setup reserved wireless IP address on the WRT54G router. With all the kids devices, when I reset the router, getting all the devices online is a challage. Some end up with duplicate IP address causing conflicts. If I could reserve an IP address for a specific device. Let me know what option the router has?
View 3 Replies View RelatedWhen I had DSL, my WRT54G was my DHCP master for my home network. When I got AT&T U-Verse, their "gateway" became the DHCP master and also the wireless access point. But the signal was not strong enough where I wanted to use it, so I hooked up the WRT54G again. I discovered that if I connected the U-Verse gateway to the "Internet" port on the WRT54G Linksys, then my home network was split in two, which I did not want. The WRT54G access point is physically somewhat distant from my wired computer, so I wanted to keep the U-Verse gateway as the DHCP master. (The U-Verse gateway is a router with four "computer" ports but no "Internet" port.)
I followed instructions on the Linksys web site, and using my wi-fi connected computer I re-programmed the WRT54G to be "Disabled" as a DHCP server. Then I powered down and physically connected the U-Verse gateway to a "Computer" port on the WRT54G. This solved my problem: my distant wi-fi computer now has a good signal, and both computers "see" each other.
However, now I seem to have lost access to the WRT54G setup "web page." Is it possible to access the innards of the WRT54G when its DHCP service is disabled? Or would I have to reset the device to factory configuration and start all over if I wanted to make any tweaks?
Time Warner used remote access to get into my wrt54g system and create a new user id/password for security. As a result, my hp printer will no longer communicate with my computer. HP says to hook up a usb from router to printer, but there's no usb port on the wrt model I own. I hooked up a usb from computer to printer but it did nada...
View 5 Replies View RelatedI set up my daughter's Dell laptop last year to our WRT54G wireless router and I'm trying to connect to our wireless network now with another laptop (a new Dell) and can't find (or remember) my security code or pass phrase. Is there any place on the old laptop that I can access this info? How can I configure the new laptop without this info?
View 9 Replies View RelatedWhen I go to the router setup screen via 192.168.1.1 the screen does not load properly in MSIE or Firefox. Text does not load.The graphics load okay, and the dropdown boxes, checkboxes, etc. Since many of the links are from text, and all of the descriptions, it is impossible to navigate properly. I managed only by using Firefox's Page Info, Links tab and cutting & pasting. A couple of screen captures are available [URL] have downloaded the latest firmware, but while I can get to the Administration page, much less click on, the Upgrade Firmware sub-tab.
View 3 Replies View RelatedI have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed." I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it.
View 9 Replies View RelatedI'm trying to setup a Linksys wireless-g router model number WRT54G with my DSL connection. I followed the basic instructions that came with the router and towards the end of the process it says detecting network settings with a % bar. The bar fills to 100% and then asks for a password. I've tried the password my DSL company gave me along with various other things like admin etc. After I enter the password I hit enter and it just asks me for the password over and over again.
View 9 Replies View Relatedhow do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
I am finally duffing my WRT 610N (N=Never consistent in performance) main router and WRT54G that I am using up in my shop as an expander. Now I am going to a E4200 Main Router and E3000 for my secondary router (Truthfully a dual band expander).
Am I going to just simply Flash my 610 to default , disconnect it and pack it away , Setup my new E4200 , Plug in my E3000 into port 1 and go about giving it a separate IP Addy? Or can I expect a **bleep**? Any setup tips?
Wirelessly I am running 2 laptops , a PS3 , Xbox 360 , Epson printer , a picture frame and Samsung Blue Ray and TV, and on occasion 2 android phones. On the Wired side (Ethernet) I have a Sling Box , a Desktop , and the router up in the shop. This is the normal load and never everything all at once (Although it has been done).
I have two PCs hooked up to the same router, a BEFSR41. Both connect to the internet fine. One can access the router setup/admin page fine. On the other one, though, the router asks for a user name and p/w, but the setup screen never loads. I get the eternal "Loading" message but it never gets there.
[code]....
I've currently got a WRT54G and have an opportunity to buy a WRT54GS. The problem is that the seller of the WRT54GS has lost the Set-Up Wizard CD & Hard Copy Quick Installation Guide. Obviously I have these items already with my WRT54G. My question is this. Are these items different for the WRT54G or will the stuff I already have for the WRT54G "work" for the WRT54GS.
View 5 Replies View RelatedI assign private IP for each PC within LAN. And DHCP is in charge of wireless connection since 192.168.0.100 for 10 clients. ,Web setup access is also disable for wireless connection.When a notebook connect to WRT54G via wireless. Private IP is always out of range and it could accesses web setup.What happen to my WRT54G ?
View 3 Replies View Relatedjust set up my EA6500 in bridge mode, i have the Ethernet cable plugged into the EA6500's yellow WAN port, is that correct, Cisco Article ID: 24583 is not that clear, Cannot also seem to access the EA6500's settings to setup security?
View 2 Replies View RelatedI have a WRT54G V8 and everyone says the username to sign is is blank and the password is admin. I have tried this and it does not work. I have also reset the router several times and this also does not work.
View 2 Replies View Related[URL]I have a Linksys E4200, even if i put wireless on manual WPS is still working, any answer from Linksys?
View 5 Replies View RelatedHow to setup WRT54G in router mode
View 9 Replies View Relatedi have a Linksys modem BEFSR81 v.3 and am trying to reset my wifi password for secure connection. When i log into the the admin page, to my surprise, I could not find the security feature to create WPA or WEP password. i'm stumped. This has never occurred to me before on this modem.
View 6 Replies View RelatedI have a 4 year old Linksys WRT54G V8 I'd like to set up as an access point for an Xbox 360 or DirecTV box. I am using a Linksys E3000 as my wrieless router, atm, and was wondering if there was anyway to use the WRT54G as an access point before I go out and buy other network adapters to get these devices connected.
View 2 Replies View RelatedHow do I make my home network secure. I am with virgin media and have a Linksys Router
View 1 Replies View Related