Linksys Wireless Router :: WRT54G V6 Setup Screen Not Loading Properly

Apr 27, 2007

When I go to the router setup screen via 192.168.1.1 the screen does not load properly in MSIE or Firefox. Text does not load.The graphics load okay, and the dropdown boxes, checkboxes, etc. Since many of the links are from text, and all of the descriptions, it is impossible to navigate properly. I managed only by using Firefox's Page Info, Links tab and cutting & pasting. A couple of screen captures are available [URL] have downloaded the latest firmware, but while I can get to the Administration page, much less click on, the Upgrade Firmware sub-tab.

View 3 Replies


ADVERTISEMENT

Linksys Wireless Router :: WRT54G No Access After Loading Configuration

May 22, 2012

I have a WRT54G with updated firmware.  Today I saved my configuration to a config.bin file.  When I tried loading the file, the admin screen went blank.  Now I am no longer able to access either the internet or the router's admin page.   Is a hard reset my only option?

View 6 Replies View Related

Linksys Wireless Router :: WRT54G V8 Browser Firmware Update Screen

Jan 9, 2012

I have a wrt54G v8 wireless router and I was trying to install a firmware update a while ago and got impatient, stopped the upgrade in the middle of it and I think I may have bricked my router. I've since tried the 30/30/30 reset a number of times and have noticed that I don't get a blinking power light which I guess means it's ok.
 
Now when I go to 192.168.1.1 and log in, I can see most menus but when I click the firmware update menu (there's another screen that's also all white, I forget which one), it's all white (or blank). I've searched for a solution on the web and no luck so far.
 
I've been trying to do this on a mac and no luck. I then booted into windows 7 and used IE 9 to log into 192.168.1.1 and still the same thing, the firmware update screen is blank.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Notebook Screen Closed / Went To Standby Mode / Stopped Upgrade Process

Jan 18, 2012

I was upgrading the firmware of the WRT54G router when the notebook´ screen closed and it went to standby mode. It was stoped the upgrade process.Now only the ports and Internet LEDs light up, but the power LED is off.I also cannot connect to thenavigator for show the administrator´s window. Any procedure to recover the operation of the router in a situation like this?

View 1 Replies View Related

Linksys Wireless Router :: WRT54GS V5 Incomplete Setup Screen

Mar 23, 2013

I've just discovered that my wireless router is not secure (WRT54GS v5). In trying to set up the propoer security, the set up screen appears as incomplete (after entering 192.168.1.1). It only shows 3 tabs at the top - Basic Setup, MAC Address Clone, and Advanced Routing. No tab to deal with the settings. I have tried resetting the router and plug/unplug several times. Triued entering thru IE and Firefox.Is there another way to set up the security on my router or at least get the proper screen?

View 4 Replies View Related

Connecting To Linksys Router 192.168.1.1 - No Login Setup Screen

Dec 8, 2012

Cannot connect to Linksys Router 192.168.1.1 Webpage, do not get login setup screen.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Setup Without CD?

Oct 1, 2012

I have a WRT54G wireless router that I haven't used in years because my old cable provider supplied me with a router.  I recently switched cable providers & they don't provide a wireless routers.  I would like to use my WRT54G router, but I don't have the cd.  I figured it wasn't a problem because I can just do a manual setup using the ip address 192.168.1.1.  I receive the pop up window to enter the user name & password.  I follow the instructions & just type in the password field the word admin & l left the user name blank but it doesn't work. 

View 4 Replies View Related

Linksys Wireless Router :: WRT54G V8.2 Cannot Access Setup

Apr 13, 2012

I had my router settings in a file on my hard drive so I would not lose them. Just my luck, my hard drive took a giant dump and the restore did not restore 100% and guess which file was among the missing?So I've followed about 15 different "reset" instructions which includes holding the reset button for 10-60 seconds; unplugging the router afterwards for anywhere from immediate to 60 seconds. Obviously, none of those sets of "sage" advice had any influence whatsoever on my router. My "server" is of my own creation:

Core2 Quad Q9550;
8 GB PC28500;
Gigabyte GA-EP45-UD3R;
Windows 7 Ultimate 64 bit SP1.
Cable Modem RCA DCM425.

View 5 Replies View Related

Websites (facebook) Not Loading Properly?

Jun 28, 2012

I can log in my facebook account, check notifications, but that's it. Images won't load, the page won't render properly, can't check messages or use games or apps. Another thing worth nothing is that the page loads extremely slowly. Most other websites work normally. This has been going on for 3 days now.

I've done lots of troubleshooting already. I normally use Google Chrome so I tried IE and Mozilla but the page looks the same. The default font (Times New Roman) and white background are the symptoms of something (what?). I've only got a wireless connection and I'm suspecting there could be a problem there because my wife has the same problem on her laptop. We share the wifi connection.We've tried a lot of things: clear browsing data (cache, cookies, etc.) flush dns, restart computers, browsers, update anti-virus software, but no success, so far.

This looks normal:
C:>ping facebook.com

Pinging facebook.com [69.171.224.37] with 32 bytes of data:

Reply from 69.171.224.37: bytes=32 time=317ms TTL=230
Reply from 69.171.224.37: bytes=32 time=314ms TTL=230[code]....

So something must've happened around 3 days ago when everything still worked fine. One thing I haven't investigated is this wifi device: Huawei E585. I have no idea how to do any troubleshooting with it. one more thing I tried: proxy servers. I thought our ISP might have changed something somewhere (although all our friends have no problems) so I tried to log in through a few different proxy servers. The login page looked normal so I logged in. The page kept loading forever but it never showed any content. I didn't even get to see that Times New Roman font. But then again, it couldn't be an issue with my facebook account because I can use it normally on my cell phone. Well, as normally as you can use it on a cell phone.

View 8 Replies View Related

Linksys Wireless Router :: WRT54G - Port Forwarding Setup

Feb 12, 2012

I'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?

View 1 Replies View Related

Linksys Wireless Router :: Wrt54g Nothing Works After Security Setup

Jun 7, 2012

my mother in law thought she forgot her wifi password so i tried to do a reseti reset it then no internet at all and could not access the router gateway page (192.168.1.1)I had to set the internet protocol to default and 2 power cycles later i can access the internet.Then i used the linksys disc to set up the security and now it doesn't work can't access nothing through ie.

View 1 Replies View Related

Linksys Wireless Router :: Cannot Access WRT54G Setup Page

Jan 19, 2013

I have a WRT54G router that I have not used for many years, but now I need to use it again. I have connected it between my modem and PC, and I am able to get an internet connection on the PC, but I am unable to connect to the router's configuration page. I have tried resetting the router numerous times (holding the reset button 5 seconds, 10 seconds, even longer) to reset the IP address to the default 192.168.1.1 address, but still cannot access the page. The power LED is on and the WLAN and Internet LEDs are on, and the LED for the port my PC is connected to is on. The hardware version of the router is v3. I tried downloading the latest firmware, but without being anble to communicate with the router at the IP address I cannot update the firmware. How can I go about connectiong to the router's setup page? When using ipconfig, the Default Gateway appears to still point to my ISP's IP address instead of the router's.

View 9 Replies View Related

Linksys Wireless Router :: WRT54G Showing As WRT54GL In Setup

Dec 4, 2011

I have a Linksys Router that shows WRT54G Ver 3 on its base, but when I go in the settings I realized it says WRT54GL over there.

View 1 Replies View Related

Linksys Wireless Router :: Download Setup For WRT54G V8 - Lost CD

Feb 27, 2009

I have lost my installation disk for my WRT54G Version 8.  Where I can download the drivers and installation.

View 9 Replies View Related

Linksys Wireless Router :: Wrt54gl And Wrt54g Setup WDS But Can't Login

Jul 18, 2011

I have wrt54gl setup with dd-wrt standard version running hotspotsystem.  3 wrt54g version 5 with dd-wrt micro setup as WDS client of wrt54gl.  After the intial setup I can log into the main router wrt54gl (192.168.1.1)and all 3 WDS routers (192.168.1.2 ,3 and 4), but after couple of days of testing suddenly i can not login to 2 of the WDS routers,
 
I mean I can connect to it and it will get me to internet but I can no longer login, it just says the page take too long to load.  I know if I do a hard reset and setup WDS again then it will work, but I dont want to keep doing that. Tried to power cycle the router but still wont work.  Is it the load on the router made it inaccessible ? 

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - Possible To Setup Reserved IP Address?

Sep 8, 2012

I wanted to know if you can setup reserved wireless IP address on the WRT54G router. With all the kids devices, when I reset the router, getting all the devices online is a challage. Some end up with duplicate IP address causing conflicts. If I could reserve an IP address for a specific device. Let me know what option the router has?

View 3 Replies View Related

Linksys Wireless Router :: WRT54G - How To Access Setup Page

Apr 27, 2012

When I had DSL, my WRT54G was my DHCP master for my home network.  When I got AT&T U-Verse, their "gateway" became the DHCP master and also the wireless access point.  But the signal was not strong enough where I wanted to use it, so I hooked up the WRT54G again.  I discovered that if I connected the U-Verse gateway to the "Internet" port on the WRT54G Linksys, then my home network was split in two, which I did not want.  The WRT54G access point is physically somewhat distant from my wired computer, so I wanted to keep the U-Verse gateway as the DHCP master. (The U-Verse gateway is a router with four "computer" ports but no "Internet" port.)
 
I followed instructions on the Linksys web site, and using my wi-fi connected computer I re-programmed the WRT54G to be "Disabled" as a DHCP server.  Then I powered down and physically connected the U-Verse gateway to a "Computer" port on the WRT54G.  This solved my problem:  my distant wi-fi computer now has a good signal, and both computers "see" each other.
 
However, now I seem to have lost access to the WRT54G setup "web page."  Is it possible to access the innards of the WRT54G when its DHCP service is disabled?  Or would I have to reset the device to factory configuration and start all over if I wanted to make any tweaks?

View 3 Replies View Related

D-Link DAP-1522 :: ADSL Web Pages Not Loading Properly

Feb 17, 2012

I'm connecting to the internet via ADSL. The modem is in our living room and has a DIR-655 connected to it. Also connected are an IPTV set-top box and an Xbox 360. In our office room we have 2 computers and a Buffalo LinkStation hard drive connected by wire to a DAP-1522 which is working as a bridge for the wireless network created by the DIR-655. The reason for this configuration is that the set-top box refused to work with IPTV through the wireless bridge. Before we got IPTV, the bridge was in the living room and was primarily used for Xbox, while the modem was in the office and allowed all desktop PCs to connect by wire.

Ever since we've had the desktop PCs connected via the bridge, surfing has been difficult. Download speeds are good, but very often webpages simply refuse to load. The browser just says "Connecting to [internet address here]. For example, I might log on to Facebook, have the front page load and then I try to open a picture someone has uploaded, but nothing happens. Clicking links, nothing happens. Clicking anywhere, nothing happens. Put a new address in the address bar, nothing happens. It just tries to connect the addresses, but won't.After waiting a while, or restarting the browser, it might work again for a while.

Is it my new modem, the DIR-655 or the DAP-1522? All devices get their IPs from the ADSL modem to ensure proper networking between the devices. Streaming from the NAS to the Xbox is flawless.

View 4 Replies View Related

Linksys Wireless Router :: WRT54G V8 / Unable To Navigate The Basic Setup Page

Jan 14, 2008

I have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed."  I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it. 

View 9 Replies View Related

Linksys Wireless Router :: Setup WRT54G With DSL Connection / Unable To Enter Password

Feb 2, 2007

I'm trying to setup a Linksys wireless-g router model number WRT54G with my DSL connection. I followed the basic instructions that came with the router and towards the end of the process it says detecting network settings with a % bar. The bar fills to 100% and then asks for a password. I've tried the password my DSL company gave me along with various other things like admin etc. After I enter the password I hit enter and it just asks me for the password over and over again.

View 9 Replies View Related

Linksys Wireless Router :: Setup Wrt54g As Access Point To Extend Signal?

Aug 17, 2011

how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
 
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?

View 1 Replies View Related

Linksys Wireless Router :: WRT610N / WRT54G / E4200 / E3000 - Setup Tips

Aug 5, 2011

I am finally duffing my WRT 610N (N=Never consistent in performance) main router and WRT54G that I am using up in my shop as an expander. Now I am going to a E4200 Main Router and E3000 for my secondary router (Truthfully a dual band expander).
 
Am I going to just simply Flash my 610 to default , disconnect it and pack it away , Setup my new E4200 , Plug in my E3000 into port 1 and go about giving it a separate IP Addy? Or can I expect a **bleep**? Any setup tips?
 
Wirelessly I am running 2 laptops , a PS3 , Xbox 360 , Epson printer , a picture frame and Samsung Blue Ray and TV, and on occasion 2 android phones. On the Wired side (Ethernet) I have a Sling Box , a Desktop , and the router up in the shop. This is the normal load and never everything all at once (Although it has been done).

View 5 Replies View Related

Linksys Wireless Router :: WRT54G Setup Wizard CD And Hard Copy Quick Installation

Jun 17, 2007

I've currently got a WRT54G and have an opportunity to buy a WRT54GS. The problem is that the seller of the WRT54GS has lost the Set-Up Wizard CD & Hard Copy Quick Installation Guide. Obviously I have these items already with my WRT54G. My question is this. Are these items different for the WRT54G or will the stuff I already have for the WRT54G "work" for the WRT54GS.

View 5 Replies View Related

Linksys Wireless Router :: WRT54G Getting Unstable Wireless Setup

Dec 25, 2011

I assign private IP for each PC within LAN. And  DHCP is in charge of wireless connection since 192.168.0.100 for 10 clients. ,Web setup access is also disable for wireless connection.When a notebook connect to WRT54G via wireless. Private IP is always out of range and it could accesses web setup.What happen to my WRT54G ?

View 3 Replies View Related

Linksys Wireless Router :: WRT54G V8 - Wireless Router Setup Password?

Jan 3, 2013

I have a WRT54G V8 and everyone says the username to sign is is blank and the password is admin. I have tried this and it does not work. I have also reset the router several times and this also does not work.

View 2 Replies View Related

Linksys Access Point :: How To Setup WRT54G In Router Mode

Jan 20, 2007

How to setup WRT54G in router mode

View 9 Replies View Related

Linksys WRT54G Setup As Access Point On Wireless Network?

Jun 28, 2011

I have a 4 year old Linksys WRT54G V8 I'd like to set up as an access point for an Xbox 360 or DirecTV box. I am using a Linksys E3000 as my wrieless router, atm, and was wondering if there was anyway to use the WRT54G as an access point before I go out and buy other network adapters to get these devices connected.

View 2 Replies View Related

Cisco Routers :: Linksys Wireless-g Broadband Wrt54g Wifi Protected Setup

Apr 10, 2012

I am using a Linksys Wireless-G Broadband Router(Model WRT54G). I am trying to set up a desktop computer to have a wireless usb adapter running so I can connect to the Wireless-G Broadband Router. When I run the setup CD for the wireless usb adapter it asks me to push the Wi-Fi Protected Setup Button on the Linksys Wireless-G Broadband Router.

I have looked at the Linksys router found an obscure button on the front with the Cisco Systems Copyright logo on it.  I pushed this but the wireless usb adapter failed to locate the wireless network.  There is also another button on the back of the Linksys Router that is a Reset button.

View 1 Replies View Related

Linksys Wireless Router :: E1200 Loading Videos And Images?

Apr 21, 2012

Having problems with the E1200 when it comes to loading images and vidoes.  Text loads fast, but images take several minutes, and for videos - forget about it, takes at least 15 minutes to load even a 2 minute video.  I've changed MHz settings and several other settings, but nothing seems to have worked.

View 1 Replies View Related

Linksys Wireless Router :: E2500 - Page Not Fully Loading

Mar 24, 2013

It's' my first router (E 2500) one desk top and two laptop and also a Ipad connected, every thing look fine exept for the Ipad.Lots of page not fully loading, I have to reload couples of time to get it full load. and lots of Youtube video said not presently availale but work fine with laptop or desktop.Did not change any seting on the router, I just plug it and used it

View 9 Replies View Related

Linksys Wireless Router :: WRT160NV2 - Get Screen To Pop Up To Change Settings?

Sep 11, 2012

I have a computer that is connected to a linksys wireless router model WRT160NV2. I also have a laptop. I have never set up a lock or anything on my wireless connection and I think other people are using it. When I type the IP address 192.168.1.1 on my laptop, I do not get the screen to pop up to change my settings. Do I need to do this from the computer?

View 1 Replies View Related

Linksys Wireless Router :: WRT160Nv2 How To Access Config Screen

Jan 7, 2011

how i can change WRT160Nv2 settings if i cannot find it with default 192.168.1.1;i'm using it as secondary router connected to FIOS actiontec primary, which has the 192.168.1.1; factory default reset linksys to that same IP, can't get it.cannot get internet without actiontec as its coax connected, and linksys doesn't have coax port.can'ty open configure page without internet connection, i believe.tried to use a neighbor's wireless but that's using 192.168.1.1 as well, can't log in to that.this started with firmware upgrade of linksys which left it invisible; didn't complete the upgrade, i don't think. but i've reset it and still nothing.

View 9 Replies View Related

Linksys Wireless Router :: E2500 Makes Websites Loading Slow

Mar 14, 2012

I have on Desktop wired to the router which is my main pc. When I access internet the website load really slow, but when I connect the pc directly to Comcast modem, it's blitz fast. My internet speed is 15 Mbps. I have another desktop and laptop. None of them have the problem. What settings I have to change to get back to speed I used to have before.I messed up some settings on the Cisco Connect and accidentally reset the router. After re-installing the router the problem started.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved