D-Link DAP-1522 :: ADSL Web Pages Not Loading Properly
Feb 17, 2012
I'm connecting to the internet via ADSL. The modem is in our living room and has a DIR-655 connected to it. Also connected are an IPTV set-top box and an Xbox 360. In our office room we have 2 computers and a Buffalo LinkStation hard drive connected by wire to a DAP-1522 which is working as a bridge for the wireless network created by the DIR-655. The reason for this configuration is that the set-top box refused to work with IPTV through the wireless bridge. Before we got IPTV, the bridge was in the living room and was primarily used for Xbox, while the modem was in the office and allowed all desktop PCs to connect by wire.
Ever since we've had the desktop PCs connected via the bridge, surfing has been difficult. Download speeds are good, but very often webpages simply refuse to load. The browser just says "Connecting to [internet address here]. For example, I might log on to Facebook, have the front page load and then I try to open a picture someone has uploaded, but nothing happens. Clicking links, nothing happens. Clicking anywhere, nothing happens. Put a new address in the address bar, nothing happens. It just tries to connect the addresses, but won't.After waiting a while, or restarting the browser, it might work again for a while.
Is it my new modem, the DIR-655 or the DAP-1522? All devices get their IPs from the ADSL modem to ensure proper networking between the devices. Streaming from the NAS to the Xbox is flawless.
View 4 Replies
ADVERTISEMENT
Jan 9, 2012
I have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection. After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.
View 9 Replies
View Related
Apr 26, 2011
My problem is two-fold:
1. the DAP-1522 will not connect to the 5GHz network of the DIR-815. Although, this doesn't surprise me as none of my 5GHz-capable devices see it, other than intermittently and at low signal. It is most likely an issue with the 815's 5GHz radio/network.
2. OTOH, the 1522 does appear to connect to the 815's 2.4GHz network just fine. However, there is no Internet access for any of the devices connected to the 1522's ports.
I know the 1522 can work correctly on 2.4GHz, as it previously did fine with my prior 2Wire router from AT&T. (I've just switched to Comcast, using the DIR-815 connected to their SMC modem.)
Also, I know the router and modem work fine (at least with 2.4GHz), as all of my wireless devices connect easily and with screaming bandwidth to the router and Internet.
View 4 Replies
View Related
Apr 8, 2013
I am using a Netgear DG834N modem/router that we moved onto our second phoneline (homeline) that was previously installed on our (now closed down) home office phoneline. We are using the same equipment, provider and provider plan but now we are having major connecting issues. About every second web page will not open. If you refresh, sometimes it will load other times you get the "IE cannot connect to.." This is becoming increasingly frustrating. We run both wireless and hardwired PCs and laptops and use IE, firefox and/or Safari. We run Kaspersky or bitdefender, windows 7 and XP. We can watch re-runs of Tv shows and you-tube no worries. It is the connecting in the first place.
View 5 Replies
View Related
Sep 11, 2012
I have Imac 21.5 inch 2011 Oct series. with 2.5 GHZ , 8 gig ram.My problem is that for some reasons sometimes I cannot load into simple web pages, I get error message like " Server not found "Firefox can't find the server at [URL]But this website and the others work fine on my laptop which runs vista. I assume it is sort of network problem or a router problem, I've connected Ethernet cable directly to my Imac but still, same situation either with FireFox or Safari.
View 1 Replies
View Related
Mar 5, 2012
I'm having problems loading web pages. It's inky on one laptop as other devices and pcs work. The laptop in question is running windows 7 and I haven't made any substantial changes to it as of late. The network centre says I'm connected to the router with full bars. When I use chrome it comes up with a dns lookup failed error, IE7 just says cannot display, when I click diagnose nothing comes up. So far I have changed the dns server addresses to 8.8.8.8 and 8.8.4.4 under internet protocol version 4. This worked until restarting the laptop. I've also typed, under advice, something in the cmd box for dns flush
View 1 Replies
View Related
Dec 4, 2012
MSI netbook. It used to be very loading pages but now is is very very slow and has been for a month or so.
View 4 Replies
View Related
Feb 3, 2013
Since yesterday, nearly every time I load a web page it either doesn't stop loading or sometimes doesn't even load at all. At first I thought that the problem was just with Chrome, but I've since tried Firefox and Explorer and get the same issue. I've tried scanning for viruses, malware and even ran Boostspeed to see if it will solve the problem, but nothing has worked.
I don't know why this has happened all of a sudden, I've not made any significant changes or installed anything new so I'm stumped. I have the fastest fiber optic package my ISP has, so it isn't down to not having enough bandwidth.Can I try resetting my router with the pinhole at the back, or will that cause me to lose settings, which I won't be able to restore ,and not be able to connect to the internet at all? (I know the routers password)
View 1 Replies
View Related
Sep 19, 2012
I'm on a wired business network. Some of the machines are Windows 7 and some are XP Pro, but all of us are having issues connecting to web pages, especially pages with lots of pictures. If you refresh it a few times, it may pop up. Some don't ever come up, like weather.com. The server has the same issue, even if you connect it directly to the router.
View 10 Replies
View Related
Jul 17, 2012
My computer surfs the internet great for about 5-20 minutes, then it will stop loading pages. I have to restart my computer to get it to start up again. I usually use Google Chrome and when it stops I have checked Internet Explorer to see if it works but it won't load any pages either. I also have checked the connection and it says I'm online. I did the trouble shooting guide for Internet Explorer and that got me no where. I did the ping thing and it checked out that I'm online. It still won't load any pages unless I keep restarting my computer. I have Windows XP and don't know what to do?
View 14 Replies
View Related
Nov 18, 2011
I am working on setting up a Linksys router for my Dad. I am moderately competent with networking. Anyway, a glaring, and obnoxious problem I am having is everytime I load a page for the router(192.168.1.1), it does not completely load and I have to hit refresh.Now when I try to change the router settings from DHCP to PPPoE, it reloads the page, for whatever reason, and because this router wants to be irritating, it only half loads the page, so I cannot click the "save settings" button.This is what has been done to the router after being reset(red button on the back held in for 10 sec):I turned on the modem, and plugged directly in to make sure I had internet connection.I plugged the modem's ethernet into the "Internet" port on the wireless router.And finally, I plug an ethernet cable from my computer to the 1st port on the wireless router.Nothing else has been changed. I have not turned on any ridiculous settings. This half-loading router pages is driving me up the wall though. I cannot even troubleshoot the wireless connectivity because I cannot make any changes.
View 7 Replies
View Related
Mar 29, 2012
I just bought a XPS 8300, I use Google Chrome for a browser, cable modem internet connection, and quite often, web pages will not load quickly, or will take a couple of reloads to load properly. Any advice on how to cure this annoying trend of mine?
View 1 Replies
View Related
Aug 25, 2012
With firmware 1.0.4.17 I am have issues with configuration pages not loading and needing to restart the web interface and login again. This is a new problem that started after updating to 1.0.4.17
How many months until we can expect a fix?
View 3 Replies
View Related
Feb 1, 2013
i have a really simple home network setup using the Cisco 871W 4-Port 10/100 Wireless G Router (CISCO871W-G-A-K9). I can't figure out for the life of me what is going on. Web pages seem to "half load" sometimes (netflix, facebook, bank of america doesn't load at all, etc). It doesn't always happen. Sometimes the pages will load fine. I have tested with multiple computers so I know that it is the router itself. Below is my configuration. Ignore anything regarding the wifi. I know that isn't set up correctly. I'll deal with that later. I wanted to see if i was missing anything. Config is really basic. Attached is what one of the "half loading" web pages looks like
!
version 12.4
no service pad
service timestamps debug datetime msec
[Code].....
View 3 Replies
View Related
Jun 28, 2012
I can log in my facebook account, check notifications, but that's it. Images won't load, the page won't render properly, can't check messages or use games or apps. Another thing worth nothing is that the page loads extremely slowly. Most other websites work normally. This has been going on for 3 days now.
I've done lots of troubleshooting already. I normally use Google Chrome so I tried IE and Mozilla but the page looks the same. The default font (Times New Roman) and white background are the symptoms of something (what?). I've only got a wireless connection and I'm suspecting there could be a problem there because my wife has the same problem on her laptop. We share the wifi connection.We've tried a lot of things: clear browsing data (cache, cookies, etc.) flush dns, restart computers, browsers, update anti-virus software, but no success, so far.
This looks normal:
C:>ping facebook.com
Pinging facebook.com [69.171.224.37] with 32 bytes of data:
Reply from 69.171.224.37: bytes=32 time=317ms TTL=230
Reply from 69.171.224.37: bytes=32 time=314ms TTL=230[code]....
So something must've happened around 3 days ago when everything still worked fine. One thing I haven't investigated is this wifi device: Huawei E585. I have no idea how to do any troubleshooting with it. one more thing I tried: proxy servers. I thought our ISP might have changed something somewhere (although all our friends have no problems) so I tried to log in through a few different proxy servers. The login page looked normal so I logged in. The page kept loading forever but it never showed any content. I didn't even get to see that Times New Roman font. But then again, it couldn't be an issue with my facebook account because I can use it normally on my cell phone. Well, as normally as you can use it on a cell phone.
View 8 Replies
View Related
Apr 27, 2007
When I go to the router setup screen via 192.168.1.1 the screen does not load properly in MSIE or Firefox. Text does not load.The graphics load okay, and the dropdown boxes, checkboxes, etc. Since many of the links are from text, and all of the descriptions, it is impossible to navigate properly. I managed only by using Firefox's Page Info, Links tab and cutting & pasting. A couple of screen captures are available [URL] have downloaded the latest firmware, but while I can get to the Administration page, much less click on, the Upgrade Firmware sub-tab.
View 3 Replies
View Related
Mar 27, 2013
Region : Malaysia
Model : TL-MR3040
Hardware Version : V1
Firmware Version : TL-MR3040_V1_120822
ISP : Celcom
There is a website that does not load when the router is in a certain setting. The website I tried to access was url...I have tried the different firmwares and settings and have narrowed it down to the AES encryption.Have tried the original 120328 firmware, works perfectly with all different settings.With the 120822 firmware, it works with all settings EXCEPT when AES is chosen as the encryption method, be it using WPA or WPA2 Personal.
I therefore pinpoint the AES encryption mode in the 120822 firmware to have a bug. I need to use 802.1n with AES, rather than TKIP.Can someone else using 120822, with AES encryption for wireless, verify that this is happening for them too?
View 2 Replies
View Related
Apr 16, 2011
I would like to be able to access my DSL Modem's http setup screens from my networked computers via my DIR-655 (rev B) router - but I do not know how to get the router to route to the WAN port.
At first, I had my DSL Modem's LAN IP at 192.168.0.1 and my DIR-655 at 192.168.1.1 and the rest of my home network at 192.168.1.xxx; because I had read on a forum that having the modem on a different subnet prevented potential routing problems. When I pointed my web browser to 192.168.0.1 - it would just timeout (I kind of expected that).
Now (willing to try anything), I have my DSL Modem's LAN IP at 192.168.0.2 and my DIR-655 at 192.168.0.1 and the rest of my home network at 192.168.0.xxx (DHCP range is set to assign hosts from 64 to 254). When I point my web browser to 192.168.0.2 - it still just times out.
The DSL Modem is setup in transparent bridge mode. And everything else is working well with the home network.
How can I get the DIR-655 to pass/route my http connection to the DSL modem?
View 10 Replies
View Related
Dec 26, 2011
I'm using a Dell computer CPU i7 8 gig of ram. It is wired in to the router. Why does it take so long to log into the router and bring up the different pages in the settings. I have never seen a router take so long. I have not updated the firmware version 2.02NA. I have not upgraded it yet. oh I have a cable connection. When I surf the web the pages come-up fast.
View 13 Replies
View Related
Jun 26, 2011
I needed to immediately set a schedule and block IPs, these pages are built into the router.It took forever for the pages to load it took 30 minutes to navigae 5 pages. Every time I try it.Router is good and signal is excellent but the admin router pages to configure are frustratingly slow.As a techie it is anoying, as a customer getting support by the hour spend more on a faster better quillity router were the work can be done in 1/20th of the time it takes on this router.I'd say I have a dud but once setup the router is a great performer if you do not need to admin the router further?
View 3 Replies
View Related
Dec 7, 2009
I am having issues with my freinds new DIR-825 Rev:B1 Firmware:2.02NA, The admin pages are intermittently slow to load and sometimes wont load until I power cycle the device. I am using IE8 on vista x64, and have the issue on all pc's on the network. Is there a work around for this?
View 7 Replies
View Related
Mar 10, 2013
My D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.
View 6 Replies
View Related
Jan 16, 2012
Just bought myself an 825. I've got it set up and working, but how do I prevent wireless users from accessing the setup pages for the router?
I only wish wired access to the setup pages. I'm used to doing this on my old linksys, but can't find the setting on the new router.
View 3 Replies
View Related
Jan 3, 2012
I`m new here I recently purchased the dir-615. I started configuring with cd but i couldn`t get past the step where it should verify if cables are plugged in , so I did it manually. Some pages won`t load , internet speed is slow ( Both wireless and lan speed ) . I am using a PPPOE connection , I even got my ISP to check my settings, and he said it was alright but it reduces my speed by a lot. Usually I download with 1 MB/s with the router on wi-fi I hardly get 50 kb/s and on lan max is 100 kb/s.
View 1 Replies
View Related
Sep 30, 2011
I recently had a networking guy set up a VPN for me, but for it to work properly he had to change all my IP addresses to 192.168.10.xx from 192.168.0.xx. My DAP-1522 (in bridge mode) continued to work but I am unable to log on to it, I think because it's address is 192.168.0.0. I have run into some other issues which makes me think I may need to upgrade the DAP-1522 firmware and/or assign it an address beginning with 192.168.10.xx, however I can't log on to the bridge. (Nor do I know how to change or possible reassign the DAP-1522's address through my router, a DIR-615).
View 5 Replies
View Related
Mar 12, 2012
I have a WIN XP desktop which I successfully connected to the 1522 AP - as evidence of the GUI to program it. I have the 1522 set to Bridge Mode via the switch on the unit. The 1522 has hardware version B1 and Firmware version 2.000. I joined my wireless network successfully as evidence of the Status page showing it's successfully connected and bridged to my network. I then disabled my USB wifi NIC in hopes of using my hardwired connection to the 1522 to get on the internet.
Wireless Radio : Enabled
Bridge State : Connected
MAC Address : fc:75:xxxxxx
802.11 Mode : Mixed 802.11a, 802.11g and 802.11n
Band Width : 40
Channel : 6
Network Name
(SSID) : cleveland
Wi-Fi Protected Setup : Enabled
Security : WPA2-PSK
View 3 Replies
View Related
Dec 7, 2011
I have dap-1522 version A Browser IE8 with lestest updates.
I downloaded the DAP1522_FW_1.31zip went I try to upload via the 1522 admin error not correct file.
I try three different way to download it, could the file be bad on dlinks web site?
View 4 Replies
View Related
Aug 27, 2010
I have just discovered after three weeks of testing that DAP-1522 wireless bridges are not compatible with all the new Pioneer AVR's that support internet radio and Iphone control. Anytime a DAP-1522 is powered on and on the same subnet mask as a Pioneer receiver it will cause the Pioneer to loose it's connection every 30 minutes. The receiver is then not able to connect unless it is powered off and on again. The DAP-1522 will cause this even if the Pioneer is hardwired to a router and nothing is plugged into the DAP-1522. This affects all new models of Pioneer receivers including the Elite line like I have.
I have tested this with 3 differnet Pioneer receivers and 2 DAP-1522's and always got the same results no matter what the settings were and with the 1522 in AP or bridge mode. Other Pioneer receiver owners experiencing constant disconnect problems on another forum have now also confirmed they have DAP-1522's.....and they are also pissed after spending countless hours troubleshooting.
I talked to Dlink support today and they will not admit to a problem so I can't wait to contact Pioneer tech support on Monday to let them know I have found the reason they are seeing returns on their new receivers (some cost as much as $7K) since many of the new owners like myself are exchanging them thinking they got a bad one. I'm sure Pioneer will test this immediately and force a Dlink fix or turn it over to the FCC.At this point I just wish I could get my money back since I have also already confirmed that a netgear bridge works just fine. Come to think of it, I know Dlink has a new refund policy, but I will check with my state district attorney to see if they can legally keep my money even if the product doesn't work. I don't see anything on the outside of the box with this policy so therfore I wasn't given fair warning of the policy before purchase and would not be expected to know it since it is not industry standard. Let the games begin.
View 14 Replies
View Related
Mar 14, 2012
I just purchased a DAP-1522. The sticker on the bottom says it's a version B1, with firmware 2.0.In the web interface, it says: "Firmware Version : 1.21 , Fri 26 Jun 2009"I downloaded the 2.01 firmware from the D-Link site and when I try to upload it, it says it's not an image file.
View 11 Replies
View Related
Jan 20, 2011
I have bought 1 Dlink Dwl 2100 Access Point about 1 week, it working with ( Default Gateaway 192.168.1.1) but I want connect with 2100Ap But I get Ip from my Livebox Orange.Can I get Ip From 2100Ap (Default Gateway 192.168.0.50), not by LiveBox Orange (Default Gateway 192.168.1.1).My brother live upstair (with LiveBox) I Live ground Floor and connect to Cable Utp cat5 form upstair to ground Floor. In my room I have a Switch connect to 2100Ap.
LiveBox Orange Default gateway is 192.168.1.1
Dlink dwL 2100Ap Default Gateway is 192.168.0.50
My os is windows Xp sp2
View 2 Replies
View Related
Nov 29, 2010
I have a DIR-655 router with a DAP-1522 connected in bridge mode. The firmware on the router is 1.21 and the firmware on the bridge is 1.21. I have my SSID set to broadcast on the DIR-655 with WPA-Personal encryption. When I initially setup the DAP-1522, I was able to access the setup page and connect to the DIR-655. On the status page of the DAP-1522, wireless radio is enabled and status is connected. I connected my XBOX 360, Sony BR player and DirecTV DVR to the wireless bridge and none of them can connect to the internet.
I can wirelessly access the bridge's IP, 192.168.0.50, from any computer connected to the DIR-655 but when I attempt to access the internet on any device connected to the DAP-1522, I do not get a connection. On the XBOX 360 I cannot connect my live account. On the Sony BR player, I get a message that new firmware was found, but when it attempts to connect to the internet to download it, the connection times out. Same occurs when attempting to access the internet on the DirecTV DVR receiver.
View 14 Replies
View Related
May 25, 2012
More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:
IP = 192.168.0.x various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50
Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.
View 3 Replies
View Related
Feb 14, 2012
My DIR 655 router quit working and so I called D link. She had me reset the ip to 192.168.5.x. So now my dap1522 is not connecting to the 655. I connected the dap1522 to my laptop via ether-net and typed in dink, and got nothing, then put in default ip for the 1522 and still nothing. I also tried ip scanner and it would not come up.
View 1 Replies
View Related
