I have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection. After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.
View 9 RepliesI'm connecting to the internet via ADSL. The modem is in our living room and has a DIR-655 connected to it. Also connected are an IPTV set-top box and an Xbox 360. In our office room we have 2 computers and a Buffalo LinkStation hard drive connected by wire to a DAP-1522 which is working as a bridge for the wireless network created by the DIR-655. The reason for this configuration is that the set-top box refused to work with IPTV through the wireless bridge. Before we got IPTV, the bridge was in the living room and was primarily used for Xbox, while the modem was in the office and allowed all desktop PCs to connect by wire.
Ever since we've had the desktop PCs connected via the bridge, surfing has been difficult. Download speeds are good, but very often webpages simply refuse to load. The browser just says "Connecting to [internet address here]. For example, I might log on to Facebook, have the front page load and then I try to open a picture someone has uploaded, but nothing happens. Clicking links, nothing happens. Clicking anywhere, nothing happens. Put a new address in the address bar, nothing happens. It just tries to connect the addresses, but won't.After waiting a while, or restarting the browser, it might work again for a while.
Is it my new modem, the DIR-655 or the DAP-1522? All devices get their IPs from the ADSL modem to ensure proper networking between the devices. Streaming from the NAS to the Xbox is flawless.
By now, I'm sure E4200 and other Router users that have twonky have noticed they cannot access the twonky configuration pages, as you have chosen to block them. Please give advanced users a work around to this, because if Twonky does not recognize our newer TV/devices, then we cannot play certain file formats without manually configuring the service.
View 3 Replies View RelatedJust bought myself an 825. I've got it set up and working, but how do I prevent wireless users from accessing the setup pages for the router?
I only wish wired access to the setup pages. I'm used to doing this on my old linksys, but can't find the setting on the new router.
So just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.
i cant create dlink acess point password , if I am going 192.168.0.50 then showing error massages , I am check two three computer , then the same error coming
View 1 Replies View RelatedI would like to be able to access my DSL Modem's http setup screens from my networked computers via my DIR-655 (rev B) router - but I do not know how to get the router to route to the WAN port.
At first, I had my DSL Modem's LAN IP at 192.168.0.1 and my DIR-655 at 192.168.1.1 and the rest of my home network at 192.168.1.xxx; because I had read on a forum that having the modem on a different subnet prevented potential routing problems. When I pointed my web browser to 192.168.0.1 - it would just timeout (I kind of expected that).
Now (willing to try anything), I have my DSL Modem's LAN IP at 192.168.0.2 and my DIR-655 at 192.168.0.1 and the rest of my home network at 192.168.0.xxx (DHCP range is set to assign hosts from 64 to 254). When I point my web browser to 192.168.0.2 - it still just times out.
The DSL Modem is setup in transparent bridge mode. And everything else is working well with the home network.
How can I get the DIR-655 to pass/route my http connection to the DSL modem?
I have a DIR-655 router with a DAP-1522 connected in bridge mode. The firmware on the router is 1.21 and the firmware on the bridge is 1.21. I have my SSID set to broadcast on the DIR-655 with WPA-Personal encryption. When I initially setup the DAP-1522, I was able to access the setup page and connect to the DIR-655. On the status page of the DAP-1522, wireless radio is enabled and status is connected. I connected my XBOX 360, Sony BR player and DirecTV DVR to the wireless bridge and none of them can connect to the internet.
I can wirelessly access the bridge's IP, 192.168.0.50, from any computer connected to the DIR-655 but when I attempt to access the internet on any device connected to the DAP-1522, I do not get a connection. On the XBOX 360 I cannot connect my live account. On the Sony BR player, I get a message that new firmware was found, but when it attempts to connect to the internet to download it, the connection times out. Same occurs when attempting to access the internet on the DirecTV DVR receiver.
More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:
IP = 192.168.0.x various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50
Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.
I have a DIR-655 set up as follows: [code] Lost Internet Access on my DAP-1522 on only my wireless laptop connection, but not other wireless nodes on the DAP-1522.I have most of my wireless nodes attached to the DIR-655, which is upstairs. Downstairs is where the DAP-1522 is located. There is a wired connection between the DIR-655 and DAP-1522. The DAP-1522 is being used as a Access Point. On this I have only three nodes that are wireless. My Smartphone, iPad and my laptop. There are also three nodes that are using the wired ports with no issue accessing the internet. The setup above have being working for over two years with no issue. Then three days ago my laptop connects to the DAP-1522, but has "No Internet Access." If I change my wireless connection to the DIR-655 on my laptop, then I do have internet connection. My Smartphone and iPad still are able to access the DAP-1522 and get the internet.
I have deleted my DHCP Reservation for only my laptop on the DIR-655. Wireless connection to the DAP-1522, looked at the DIR-655 and see that DHCP Reservation show the MAC of the laptop and I Reserve it. Still "No Internet Access." On the DAP-1522 it does show that my laptop is associated to this device. I cannot ping my local LAN IP Addresses , a website or Public IP Address only from the laptop. The DIR-655 shows a "Do Not Enter: Wireless system with MAC address 4025C2B97110 disconnected for reason: Received Deauthentication" with a connection to the DAP-1522, but shows "Do Not Enter: Wireless system with MAC address 4025C2B97110 secured and linked" with a connection to the DIR-655.
I have 4 DAP-1522's bridging to a WNDR3700v2. Any device plugged into any of the 1522's can access the internet and can access shared drives etc. on any other device plugged into any 1522. I can access the WNDR3700 admin website from a device connected to a 1522.
However, no device plugged into a 1522 can access a device plugged into the 3700's ethernet switch. Likewise, the devices plugged into the 3700 cannot access devices plugged into 1522s.
Devices plugged into the 3700's switch can access the internet and can access each other.
I have changed network cables, power cycled all devices (PCs, bridges, routers, etc) at least once. I am running latest firmware on 1522's and 3700. In short, I've tried just about all the basic stuff.
It almost appears that the 3700's switch is acting as an isolated network. I would say that were true, except that I can access the router admin page from anywhere (any 1522 and directly connected to the 3700).
All devices are within the 10.0.0.x address range with a subnet mask of 255.255.255.0. Again, I have no problems accessing the internet. Just the problem of devices plugged into a 1522 communicating with devices plugged into the 3700 and vice versa.
I have a Netgear WNDR3300 Dual-Band and is setup to use both 2.4Ghz and 5Ghz to achieve 300 Mbps connection.
On the DAP-1522, I use IE (not Firefox or Chrome) for configuration as follow:
- IP address: STATIC
- Wireless config: using Wizard
- Wireless security: WPA2 / AES
- Mac Cloning: disabled
I tested this by connecting a Windows 7 desktop AND laptop via Ethernet cable and both laptop can obtain IP address dynamically, so my DAP-1522 is talking to the WNDR3300 (it has DHCP). Both Win 7 machines can also access the Internet.The problem is, I can NO LONGER access DAP-1522 admin screen, even by typing the static IP address assigned to it. The ONLY way I can re-access it is:
a). Reset DAP-1522
b). Shutdown the WNDR3300 wireless router, assign a static IP to the laptop, connect via cable to DAP-1522
I would like to use the DAP-1522 as an Access Point (wired to my router). My two concerns are:Can the 3 remaining ethernet ports be used to wirely connect to local PCs (so the DAP-1522 also acts as a switch) ? In case answer to the previous is yes, would it affect the performances of the wifi ?
View 3 Replies View RelatedI am am having all kinds of problems with setting up my router. I finally got the LAN stuff to work but the wireless will not work its like something is blocking it but I don't see anything. I can ping from wireless to any IP address but I cannot open up web pages. You would think this is DNS issue but I my DNS l looks to be fine and the same DNS works on the 8 port switches on LAN side without issue. I also thought maybe its something to do with ACL but I don't see anything there either.
I built this using a couple of other web posts: [URL]
The first one gets my LAN up and running, and the second one will let me get my wireless up and working and show my SSID but for some reason I am blocked from the internet as far as web pages, and perhaps blocked is not the correct term at this point as it could well be settings but in any case I cannot get there. My level of knowledge is around the CCENT 1, and part of the CCENT 2. I was studying for the first test with my home lab two routers and two older switches when I decided to buy this and since working on this my actual experience has pushed past the first test and pushing me to learn a lot of new things. Many of the things in the AP I still don't understand from IOS perspective. all that bridging is a bit confusing and its not in my videos I study for the test.
(I did find a bug with the 891W model: if you use the GUI and enable the wireless using CCP then you go into the command line and put in guest mode to show the ssid it bugs out and it will not show the SSID. You fix by going back into CCP and turning off SSID and then the command line will work and it shows up, weird huh, but anyway I just put that in here in case some other person is looking for 891W and runs across the error)
Edited: OK I am adding a piece of information. I can ping Google at 74.125.227.51 "from a my PC connected to the wireless AP" but when I Put that same IP into the browser it will not go through. So seems like ICMP is getting through but maybe HTTP and HTTPS are not? I may be on wrong track but seems related.
Note: When connected to the Ethernet switch port 0 of the same router (its 8 port switch built in as well) I can get to all websites via browser without any issues. Its only with the wireless that I cannot.
show runBuilding configuration...
Current configuration : 5658 bytes!! Last configuration change at 06:08:06 UTC Wed Jun 20 2012 by brian!version 15.0service timestamps debug [ code]...
With firmware 1.0.4.17 I am have issues with configuration pages not loading and needing to restart the web interface and login again. This is a new problem that started after updating to 1.0.4.17
How many months until we can expect a fix?
I got a DAP-1522 and here is my situation. I have a wireless router connected to the internet downstairs. I want to extend the range by creating a new wireless network upstairs. So I want the DAP-1522 to connect to the wireless router, and then become another access point upstairs.
I was able to connect to the wireless router in the DAP-1522 setup wizard, but nowhere was I able to configure that actual DAP-1522 WIRELESS setup. Nothing ever showed up on the "Wireless Settings". Just "Save Settings" "Do Not Save Settings" and the rest of the screen empty. On the status page it does show it is connected.
Am I doing something wrong or will the DAP-1522 not do this?
I want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
View 7 Replies View RelatedI have a defective DAP-1522, or what. First off, I have never been able to access the unit at http://DLINKAP when my computer is connected directly to the 1522 via ethernet, only 192.168.0.50 works to bring up the web interface.
Second, I have more than one AP at my house, but the DAP-1522 is the only networking device I have have problems with (I am using the unit in AP mode). Basically, the problem is the wireless connection usually is much slower than my other APs (both N and G), even when the computer is physically right next to the DAP-1522. And that's when the unit is at it's best. At it's worst, I can't connect to the internet at all, even though my laptop shows full signal strength. The 1522 just seems really finicky. The problem doesn't seem to be a networking issue, because a 2nd AP that is connected through the wired portion of the DAP-1522 works perfectly, implying the 1522 is having no networking issues when using the ethernet ports. But since the problems persist with full signal strength and with the computer right next to the 1522, it doesn't seem to be a wireless connection issue either. And I have no problems connecting to any other wireless APs I own (and I own about 5 others, not that I use them all at the same time).
If I could, I would return my 1522, but I've been tinkering with it for too long now to return it. It has caused me a ton of frustration. I had a wired-only router for a long time (hence the purchase of the 1522), but just bought a new wireless-N router that is performing perfectly (as a router, and as an N AP). I hoped the old router might have not been playing nice with the 1522, but have seen no improvement with the 1522 wired to the new router (on opposite ends of my home).
Note that I use Macs only, no Windows machines. I started with the 1.02 firmware for the 1522, now have 1.20 firmware, but have noticed no improvements with my issues.
Using as AP. Last Tuesday in the middle of a Netflix movie the video stopped. Now the wireless portion of the DAP-1522 refuses to pass any type of video. Everything else works (email, Google, Facebook, etc.). I can get to Netflix, Youtube, Yahoo, etc. .....but none of them will pass video.
Using a direct wired connection to the DAP-1522 everything works. Netflix, Youtube, etc.
Download speed checks at 17.74mbps.
I'm setting up A DAP-1522 in bridge mode. Network setup went fine. When I went to wireless setup I got a blank page, all white no letters, nothing. I've logged out and back in again with the same results.
View 8 Replies View RelatedI'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
I am thinking of getting the DAP-1522 access point but I wondered. Can I set it to broadcast on 5GHz for my laptop and ipad, so they can stream video. Then set the guest zone to broadcast on 2.4GHz just for my lame printer, my printer does not have LAN and only wireless b & g. If I do put the printer on the guest zone and I enable routing between zones, will my laptop be able to print to my printer?
View 1 Replies View RelatedIf I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies View RelatedI upgraded the firmware on my newly acquired DAP-1522 from v1.02 to v1.21 (the hardware ver is A1). But weird thing happened after the upgrade--the Setup->wireless network settings portion of the set up menu disappeared! I re-flashed the upgrade once more and it's still not showing. Reboot the AP--same thing!
[url]...
With firmware version 1.31, the Wireless settings page is blank when a browser other than Internet Explorer is used to access it - for instance, Firefox or Chrome.All other pages appear and seem to work properly, only the Wireless settings page is empty. Luckily, the Wizard still works and can be used to set the Wireless settings for general purpose use. Older versions of the firmware worked fine with other browsers, including the Wireless settings page.
View 6 Replies View RelatedWe currently use the DIR 655 in our home. I has a great range, and we've never had any problems. Our house is a very tall Victorian, so some areas don't get as strong a signal as others. I'd like to set up a few addition devices to extend the coverage of our network.
I installed a DAP 1522 as a bridge to our entertainment PC. After a while of trying to sort out how to configure it everything is working there. The 1522 is connected to the PC via cable.
I still want to extend the overall wireless range to better cover the lower floors and back porch.
From reading the manual on the 1522 I am a bit confused. I understand how it works as a bridge, connecting devices via cable. Will it also extend the range is set as an Access Point without needing the devices to connect via cable?
I got a new laptop for Christmas that came with the Intel(R) Centrino(R) Wireless-N 2230 card that supports 802.11N. I am only seeing connection speeds of 1500mbps rather than the 300mbps that he DAP-1522 advertises.I found this on the d-link site but from what read on the Intel site about the card it supports the 40Mhz band. url...
View 3 Replies View RelatedI have a brand new DAP-1522 A1 connected to an 802.11n wireless LAN in bridge mode. Running in the 2.4GHz band with WPK-2 and AES security/encryption.Everything runs fine 99% of the time, but once a day or so the wireless LAN connection on the DAP-1522 drops and then takes about two minutes to re-connect. It re-connects and then everything is fine for a day or so until the next dropped wireless connection episode on the DAP-1522. I know my 802.11n wireless network is 100% fine as during the dropped connection to the DAP-1522 I can connect directly to the 802.11n wireless network (running from my gateway/router) using my other computer, no issues.I've seen some posts on this forum that the A1 version of the DAP-1522 hardware is not 100% compatible with the 802.11n network standard and there will be intermittent wireless drops. If this is true, it's just insane. All I can say is I can't believe DLink would allow a product to be sold that won't work properly on 802.11n networks.I check the logs each time I see the dropped wireless connection and all that shows is the following.1) Negotiating connection 2) 4-way handshake success [mac address]There's no message in the logs about why the wireless connection dropped, but I assume it has something to do with re-newing a key for the wireless network as the successful key renewal messages are the only other messages in the log. When the wireless network dropped I don't see the successful key renewal message at the time I should see it.I thought this DAP-1522 would take 15 minutes to configure in bridge mode and then I'd forget about it. Spend too much time on this already, so a bit disappointed with this DAP-1522 and DLink tech support....though when it's connected to the 802.11n wireless LAN it works fine.
View 14 Replies View RelatedI cannot access the WRT610n setup/management pages wirelessly from my Macbook using safari. I can access the router via wireless from iPhone and PC and I can access it from the Macbook via ethernet cable.
When I try to access the router from the Macbook I just get "Contacting..." in the Safari status line and eventually it times out.
I can access the internet using Safari via WRT610n wireless. The only page I can't access is the router's management page.
how to configure AP1522 in my possession.
I have 2 AP1522 and I have to configure them so that clients can connect either 2.4 GHz or 5.0 GHz. Each of the two AP1522 must be autonomous, but has to bear in mind that are close together.
To do this I have:
- Defined the two AP1522 as RAP mode
- Set the flag on the "client access on backhault link", but I have not enabled the sub-flag "Extended backhaul Client Access" (what is this sub-flag?)
- Set 2 BGN different (but this is indispensible or I can put the same BGN? what is the difference?)
- Set the two AP1522 on two different channels (but this is necessary? or is importan only if I set the same BGN?)
- The two AP1522 appear on the WLC as a way bidge (is correct?)
How can I check if my laptop will connect using the 5.0 GHz?!? It's just turn off the antenna of 2.4 GHz?!? On my laptop I haven't found a way to force it to connect in 5.0 GHz.
Here's the setup:
DGL-4100 (wired gigabit router)
-> Wii
-> X360
-> PS3
-> DGS-2205 (wired gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522 (wireless access point/bridge)
Now, we're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. I tried entering the SSID manually, and nothing can find it.
I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies View RelatedI'm using a Dell computer CPU i7 8 gig of ram. It is wired in to the router. Why does it take so long to log into the router and bring up the different pages in the settings. I have never seen a router take so long. I have not updated the firmware version 2.02NA. I have not upgraded it yet. oh I have a cable connection. When I surf the web the pages come-up fast.
View 13 Replies View Related