D-Link DAP-1522 :: To Work As Wireless Access Point To DIR-825
Jun 4, 2011
So just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.
View 1 Replies
ADVERTISEMENT
Mar 3, 2013
i cant create dlink acess point password , if I am going 192.168.0.50 then showing error massages , I am check two three computer , then the same error coming
View 1 Replies
View Related
Apr 2, 2013
I would like to use the DAP-1522 as an Access Point (wired to my router). My two concerns are:Can the 3 remaining ethernet ports be used to wirely connect to local PCs (so the DAP-1522 also acts as a switch) ? In case answer to the previous is yes, would it affect the performances of the wifi ?
View 3 Replies
View Related
Jan 28, 2010
I want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
View 7 Replies
View Related
Dec 27, 2010
Here's the setup:
DGL-4100 (wired gigabit router)
-> Wii
-> X360
-> PS3
-> DGS-2205 (wired gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522 (wireless access point/bridge)
Now, we're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. I tried entering the SSID manually, and nothing can find it.
View 2 Replies
View Related
Jan 13, 2013
I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies
View Related
Sep 6, 2011
Is there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?
View 4 Replies
View Related
Jan 6, 2011
I have a DSL router Pirelli PDF A1000G.I have a Linksys e3000 and I have a dap-1522.When I bought a dap-1522 I thought it could do access point in fact i saw many videos in dlinktv before choosing an access point from DIY with mike etc to youtube there are 2 videos one showing bridged mode and another ap mode!Now what happens is this I have upgraded from firmware 1.11 that came as default to 1.21 i connect it wired to my linksys e3000 when it is connected with the ethernet cable wired I can connect to the internet and navigate and open sites and my ps3 can connect to it but my range is not very good only 40%!
Now I bring it downstairs remove the ethernet cable and connect it to the power and then you can connect to it but since it isn't connected to my router which is upstairs i can't access websites neither can I play on my ps3!I don't know does only ap mode works when it is connected to the router wired because what happens is if you don't put ethernet cables in the back of the dap-1522 and just connect it to power then here doewnstairs you can connect to the dap-1522 my signal is like 87% but while I'm connected with my laptop I can't access websites and in the ps3 I can't connect!
and choose access points there are (4) listed: dap-1522, dap-1160, dap-1353 and dap-2553, I thought of buying dap-1522 because it could support abgn while 1160 only supports g and 1353 only supports n to repeat to signal here downstairs and be a good access point!
View 3 Replies
View Related
Jan 9, 2012
I have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection. After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.
View 9 Replies
View Related
Jul 3, 2012
We have a task of setting up 2 new WAP in our office. We have connected them to the network ethernet port and we can all connect which is great! However I need to change the wifi name and add security! Our server has DHCP.Everything I have seen online only refers to home network where the address is 192.168 etc..
View 3 Replies
View Related
Jun 14, 2011
I needed the Guest access of wi-fi setup that LinkSysys routers provided. I don't need the router/modem i just want to have wi-fi access point. I'm an advanced user and i can work with manual setup etc.I tried to do a manual setup of the router, i changed the IP address to mask my network and enable wi-fi and worked BUT the guest access option is NOT available unless you use the stupid CISCO connect software.
Now the cisco connect software IS NOT working or complete the setup if you don't connect it through the router and gain Internet access which is IMPOSSIBLE for me to accomplish as my modem is connected to a firewall device and we are using static DSL options with PPPoE and usernameme/password. There is no way i can get cisco connect to load properly as it always "fixes my connection trying to gain Internet access".Is there any solution on manually properly setup this router and take full advantages of it capabilities or should i return it ?
View 7 Replies
View Related
Nov 29, 2010
I have a DIR-655 router with a DAP-1522 connected in bridge mode. The firmware on the router is 1.21 and the firmware on the bridge is 1.21. I have my SSID set to broadcast on the DIR-655 with WPA-Personal encryption. When I initially setup the DAP-1522, I was able to access the setup page and connect to the DIR-655. On the status page of the DAP-1522, wireless radio is enabled and status is connected. I connected my XBOX 360, Sony BR player and DirecTV DVR to the wireless bridge and none of them can connect to the internet.
I can wirelessly access the bridge's IP, 192.168.0.50, from any computer connected to the DIR-655 but when I attempt to access the internet on any device connected to the DAP-1522, I do not get a connection. On the XBOX 360 I cannot connect my live account. On the Sony BR player, I get a message that new firmware was found, but when it attempts to connect to the internet to download it, the connection times out. Same occurs when attempting to access the internet on the DirecTV DVR receiver.
View 14 Replies
View Related
May 25, 2012
More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:
IP = 192.168.0.x various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50
Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.
View 3 Replies
View Related
Apr 4, 2012
Does the Cisco 1262N Lightweight Access Point (AP) work's with Wireless LAN Controller 4402?
View 1 Replies
View Related
Dec 1, 2010
I would like to buy Cisco Aironet 1260 Access Points, i just want to use them independantly so i want to know do they work without the Wireless LAN Controller? or i have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.
View 9 Replies
View Related
Feb 24, 2011
I want to confirm if the access point (AIR-AP1141N-E-K9) can work with the Wireless LAN Controller (AIR-CT5508-25-k9)
View 2 Replies
View Related
Aug 29, 2012
I have a DIR-655 set up as follows: [code] Lost Internet Access on my DAP-1522 on only my wireless laptop connection, but not other wireless nodes on the DAP-1522.I have most of my wireless nodes attached to the DIR-655, which is upstairs. Downstairs is where the DAP-1522 is located. There is a wired connection between the DIR-655 and DAP-1522. The DAP-1522 is being used as a Access Point. On this I have only three nodes that are wireless. My Smartphone, iPad and my laptop. There are also three nodes that are using the wired ports with no issue accessing the internet. The setup above have being working for over two years with no issue. Then three days ago my laptop connects to the DAP-1522, but has "No Internet Access." If I change my wireless connection to the DIR-655 on my laptop, then I do have internet connection. My Smartphone and iPad still are able to access the DAP-1522 and get the internet.
I have deleted my DHCP Reservation for only my laptop on the DIR-655. Wireless connection to the DAP-1522, looked at the DIR-655 and see that DHCP Reservation show the MAC of the laptop and I Reserve it. Still "No Internet Access." On the DAP-1522 it does show that my laptop is associated to this device. I cannot ping my local LAN IP Addresses , a website or Public IP Address only from the laptop. The DIR-655 shows a "Do Not Enter: Wireless system with MAC address 4025C2B97110 disconnected for reason: Received Deauthentication" with a connection to the DAP-1522, but shows "Do Not Enter: Wireless system with MAC address 4025C2B97110 secured and linked" with a connection to the DIR-655.
View 6 Replies
View Related
Jun 15, 2012
i have cisco CAP 3602e series access point to work with 5500 series controller with code 7.0i did not find VCI option 60 for this type of APs to configure DHCP. How I can let these APs will join the controller, i mean through which process DNS discovery methode and what about if i need to configure option 60 and 43 in dhcp for ap joining process to controllers.
View 4 Replies
View Related
Dec 11, 2011
I have 4 DAP-1522's bridging to a WNDR3700v2. Any device plugged into any of the 1522's can access the internet and can access shared drives etc. on any other device plugged into any 1522. I can access the WNDR3700 admin website from a device connected to a 1522.
However, no device plugged into a 1522 can access a device plugged into the 3700's ethernet switch. Likewise, the devices plugged into the 3700 cannot access devices plugged into 1522s.
Devices plugged into the 3700's switch can access the internet and can access each other.
I have changed network cables, power cycled all devices (PCs, bridges, routers, etc) at least once. I am running latest firmware on 1522's and 3700. In short, I've tried just about all the basic stuff.
It almost appears that the 3700's switch is acting as an isolated network. I would say that were true, except that I can access the router admin page from anywhere (any 1522 and directly connected to the 3700).
All devices are within the 10.0.0.x address range with a subnet mask of 255.255.255.0. Again, I have no problems accessing the internet. Just the problem of devices plugged into a 1522 communicating with devices plugged into the 3700 and vice versa.
View 2 Replies
View Related
Nov 30, 2011
I have a Netgear WNDR3300 Dual-Band and is setup to use both 2.4Ghz and 5Ghz to achieve 300 Mbps connection.
On the DAP-1522, I use IE (not Firefox or Chrome) for configuration as follow:
- IP address: STATIC
- Wireless config: using Wizard
- Wireless security: WPA2 / AES
- Mac Cloning: disabled
I tested this by connecting a Windows 7 desktop AND laptop via Ethernet cable and both laptop can obtain IP address dynamically, so my DAP-1522 is talking to the WNDR3300 (it has DHCP). Both Win 7 machines can also access the Internet.The problem is, I can NO LONGER access DAP-1522 admin screen, even by typing the static IP address assigned to it. The ONLY way I can re-access it is:
a). Reset DAP-1522
b). Shutdown the WNDR3300 wireless router, assign a static IP to the laptop, connect via cable to DAP-1522
View 3 Replies
View Related
Feb 7, 2011
I've worked on it and read on it for almost 2 days and I'm stuck. I'm using a Win 7 Pro desktop that is hardwired and a Win 7 Home Premium laptop wireless. Both current on all updates.
My Comcast modem is hooked into a WRT160N that is hardwired to the desktop PC and to a WRT400N which is being used as an access point. Both routers have the latest firmware. Both routers have the same SSID, security and password but use different channels. (2 & 6) Internet works perfect both wired and wireless through both routers.
The homegroup has been set up through the desktop but I've removed and added homegroups on both machines multiple times. My problem doesn't go away. The homegroup works when the laptop is either wired or wireless using the WRT160N. It will not work at all through the WRT400N. I can be in the room with the WRT160N hooked to the homegroup, when I move to the other router so the wireless switches to the WRT400N, it drops the homegroup. The internet stays connected just fine as I move back in forth so the IDs and security has to be correct. Once the laptop drops the homegroup, it can't find it until I go back and connect to the main router.
Both machines have IPv6 addresses, auto discovery is on.
I also have an XP machine hooked to the main router. The desktop can see it but it also is invisible to anything using the WRT400N router. I also made sure all PCs are using the same Network ID with no password.
It seems to me that neither Homegroup or Home Network are passing between the two routers since everything works fine using just one router.
View 4 Replies
View Related
Feb 2, 2012
Currently have a sbs2003 with 2 nics want to install a wireless access point for the internal network. the wireless router is on the external wan how do i link the access point to this?
View 1 Replies
View Related
Jun 11, 2011
So, in an attempt to improve my signal in my house I relocated my router upstairs from downstairs by running a long cable to the modem downstairs, since I have read that the signal travels more efficiently down than up apparently. That has not been the case. Now, I have two routers. A D-link DIR-655 and a Netgear router provided by Comcast which is a WNR-1000v2.
possible to set one of these routers up as a wireless access point? Have a router upstairs be the access point, and have a router downstairs connected to the modem. This sounds like this may be a solution but let me know if I'm completely wrong. In my mind, what I'm after is more of a range extender or a repeater but at this point I don't know the difference anymore. It's been quite stressful dealing with my old man for the past week because he can't use his iPad.
View 3 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Nov 5, 2012
A friend of mine has a network with the following setup: D-Link DSL-2500U for ADSL, connected straight into a Telkom DG834GUv5 (locally rebadged Netgear) which has 2 PCs connected via cable, and 2 laptops via Wireless. A cable runs from the Telkom into a standard IPLink switch, which merely extends a cable into a D-Link DIR-615 running DD-WRT that has 2 computers connected, and shares wireless to a couple laptops.
At the moment the network is somewhat unstable, and recently the Telkom router has been giving serious problems, even after resetting to default. I want to try make the network a bit simpler and more stable. Firstly, I want to remove the IPLink switch, which merely extends the cable. Is an Ethernet Coupler what I need? Both cables are definitely under 100m combined (probably under 50m).
Now the big thing is a replacement for the Telkom (rebadged NetGear). Should I get another D-Link DIR-615 or is there a better solution? Their budget is between $40 and $60 US. Is it best to stick to the same brand, considering both devices are D-Link at present?
View 1 Replies
View Related
Mar 15, 2009
i'm facing a big problem with my access point WAG54G ver 2.0 ,i just bought it from 2 days but i find alot of problems when i start using it ,i have read all the user guide and the quick install to see how to setup the access point and make it work with my adsl.i have configured all things right using PPPOE and putting my user name and password and then save settings then go to the status and press on connect , but it don't connect with me just i find connecting and adsl link : Down and still making connecting and nothing after that and my adsl led is off haven't any colors ,and when i get again to basic setup i found the password that i put it in the ppoe login is too long , not my password i tried to see what is this password and recover the hidden i found it " d6nw5vlx2pc7st9m ".i don't know what is the problem i tried alot of times to change setting and also the same problem.i think that it's a frim ware problem and i tried install a new updated frimware but everytime trying to install it get installing and suddenly stoped and white page appeard and all the access point is stopping and when restart it the ac power.
View 3 Replies
View Related
Dec 13, 2011
I have two DIR-655s. One is my main router, connected to my modem. The other, on the other side of the house, is set up as an access point. I followed this guide to set up my AP: [URL]
Both are are hard wired. I have both of them using the same SSID. Both are 802.11g only, have the same security mode, and key. The only wireless difference is the channel. One uses 6, while the other uses 11.
On initial setup, everything is fine, but after a few hours, the AP just seems to stop broadcasting a signal. I'm using "Wifi Analyzer" on Android to monitor it. When I look at the AP, the wifi indicator light is still on. If I log into it, change the channel, and press save on the "Wireless Settings" screen, it will broadcast for a few more hours before stopping again. The wired connect of this AP always seems to work (Xbox is hard wired to it).
AP Hardware Version: B1 / Firmware Version: 2.03NA
View 14 Replies
View Related
Aug 31, 2011
So I've decided to use a different router to resolve some VPN issues, and want to use my DIR-655 as a pure wireless access point. I need the access point to use the same range of IP addresses as the rest of the network (maintain access to networked printers, file shares, etc). However, I can't establish a wireless connection to the access point.
- Defined a IP address for the DIR-655 within the DHCP range of the primary router
- Defined the proper subnet
- Disabled the DHCP server on the DIR-655
- Connect a LAN port of the DIR-655 to a LAN port on a switch (note that it's not connected directly to a router).
When I connect a device WIRED to a LAN port on the DIR-655, everything works fine. The device gets assigned a DHCP address (which I know is being assigned by the main router since the DIR-655 DHCP server is disabled), and I can connect to the LAN and I can access the internet with no problem. So I know the DIR-655 is acting correctly to pass thru traffic. Also, I can access the DIR-655 web configuration page from any LAN device (even a device not directly connected to the DIR-655), so I know the DIR-655 is on that LAN correctly.
But when I try to connect WIRELESS to the DIR-655, it doesn't work at all. Although the wireless NIC is connecting to the DIR-655 (e.g. it asks me for the WPA key), it can't pull an IP address, so there is no connection to the LAN or internet.
View 5 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Mar 12, 2012
I have a WAP54G v3.1 running firmware version 3.05.01 and a WRT54G v3 running Tomato v1.28. The WAP54G is configured client mode and works perfectly. However, I was not able to get the two to communicate with WPA2 security - maybe, I just didn't try hard enough? Both devices are capable of doing WPA2 with AES but client mode doesn't seem to work with WPA2? I had to drop back to WPA-AES to make it work. Why is this?
View 4 Replies
View Related
Jun 25, 2012
I can't figure out how to get the config right for the 802.11n channel to work.
View 4 Replies
View Related
Nov 20, 2011
How can I configure my TP-Link router TD-W8950ND act as an access point? I'll be connecting it to a main router which is connected to the ISP.
View 1 Replies
View Related
Apr 12, 2011
I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
View 1 Replies
View Related
