D-Link DIR-655 - Set Up Wireless Access Point?

Jun 11, 2011

So, in an attempt to improve my signal in my house I relocated my router upstairs from downstairs by running a long cable to the modem downstairs, since I have read that the signal travels more efficiently down than up apparently. That has not been the case. Now, I have two routers. A D-link DIR-655 and a Netgear router provided by Comcast which is a WNR-1000v2.

possible to set one of these routers up as a wireless access point? Have a router upstairs be the access point, and have a router downstairs connected to the modem. This sounds like this may be a solution but let me know if I'm completely wrong. In my mind, what I'm after is more of a range extender or a repeater but at this point I don't know the difference anymore. It's been quite stressful dealing with my old man for the past week because he can't use his iPad.

View 3 Replies


ADVERTISEMENT

Wireless :: How To Link Access Point

Feb 2, 2012

Currently have a sbs2003 with 2 nics want to install a wireless access point for the internal network. the wireless router is on the external wan how do i link the access point to this?

View 1 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related

D-Link DIR-615 :: New Wireless Router / Access Point

Nov 5, 2012

A friend of mine has a network with the following setup: D-Link DSL-2500U for ADSL, connected straight into a Telkom DG834GUv5 (locally rebadged Netgear) which has 2 PCs connected via cable, and 2 laptops via Wireless. A cable runs from the Telkom into a standard IPLink switch, which merely extends a cable into a D-Link DIR-615 running DD-WRT that has 2 computers connected, and shares wireless to a couple laptops.

At the moment the network is somewhat unstable, and recently the Telkom router has been giving serious problems, even after resetting to default. I want to try make the network a bit simpler and more stable. Firstly, I want to remove the IPLink switch, which merely extends the cable. Is an Ethernet Coupler what I need? Both cables are definitely under 100m combined (probably under 50m).

Now the big thing is a replacement for the Telkom (rebadged NetGear). Should I get another D-Link DIR-615 or is there a better solution? Their budget is between $40 and $60 US. Is it best to stick to the same brand, considering both devices are D-Link at present?

View 1 Replies View Related

D-Link DIR-655 :: Access Point Stops Broadcasting Wireless?

Dec 13, 2011

I have two DIR-655s. One is my main router, connected to my modem. The other, on the other side of the house, is set up as an access point. I followed this guide to set up my AP: [URL]

Both are are hard wired. I have both of them using the same SSID. Both are 802.11g only, have the same security mode, and key. The only wireless difference is the channel. One uses 6, while the other uses 11.

On initial setup, everything is fine, but after a few hours, the AP just seems to stop broadcasting a signal. I'm using "Wifi Analyzer" on Android to monitor it. When I look at the AP, the wifi indicator light is still on. If I log into it, change the channel, and press save on the "Wireless Settings" screen, it will broadcast for a few more hours before stopping again. The wired connect of this AP always seems to work (Xbox is hard wired to it).

AP Hardware Version: B1 / Firmware Version: 2.03NA

View 14 Replies View Related

D-Link DIR-655 :: Can't Establish A Wireless Connection To Access Point

Aug 31, 2011

So I've decided to use a different router to resolve some VPN issues, and want to use my DIR-655 as a pure wireless access point.  I need the access point to use the same range of IP addresses as the rest of the network (maintain access to networked printers, file shares, etc).  However, I can't establish a wireless connection to the access point.

- Defined a IP address for the DIR-655 within the DHCP range of the primary router
- Defined the proper subnet
- Disabled the DHCP server on the DIR-655
- Connect a LAN port of the DIR-655 to a LAN port on a switch (note that it's not connected directly to a router).

When I connect a device WIRED to a LAN port on the DIR-655, everything works fine.  The device gets assigned a DHCP address (which I know is being assigned by the main router since the DIR-655 DHCP server is disabled), and I can connect to the LAN and I can access the internet with no problem.  So I know the DIR-655 is acting correctly to pass thru traffic.  Also, I can access the DIR-655 web configuration page from any LAN device (even a device not directly connected to the DIR-655), so I know the DIR-655 is on that LAN correctly.

But when I try to connect WIRELESS to the DIR-655, it doesn't work at all.  Although the wireless NIC is connecting to the DIR-655 (e.g. it asks me for the WPA key), it can't pull an IP address, so there is no connection to the LAN or internet.

View 5 Replies View Related

D-Link DAP-1522 :: To Work As Wireless Access Point To DIR-825

Jun 4, 2011

So just recently purchased the DIR-825 and DAP-1522.  At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825.  So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router.  Pretty basic I guess.  I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.

I've been working on this since last night and got frustrated and went to bed.  I woke up fresh and decided to try again and I'm not having making any headway.

DIR-825 is connected to my DSL modem and has no problem accessing the internet.  I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet.  Encryption is disabled.  It worked with encryption but I turned it off to troubleshoot this AP problem.

It should be simple but I must be doing something wrong.  BTW is there a way to scan for network devices from the router or the access point?  I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.

So the DAP has access point enabled and 802.11 is running in mixed mode.  I've tried different variations but nothing has worked.  I've tried 20 mhz and 20-40 auto mhz channels but same problem.  Wireless security is off for troubleshooting at the moment.

DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range.  I can connect to the DAP both wirelessly and hard wired.  The problem is that it can't seem to connect to the router.  So my laptop can connect to the router and ha internet access.  And it can also connect to the DAP but does not have internet access.  The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip.  Is the router supposed to assign the ip to my laptop through the DAP?  But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.

View 1 Replies View Related

Cisco Wireless :: Point To Point Access Point 1262 Bridging

Feb 27, 2013

How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.

View 12 Replies View Related

Wireless :: Configure TP-Link Router TD-W8950ND Act As An Access Point?

Nov 20, 2011

How can I configure my TP-Link router TD-W8950ND act as an access point? I'll be connecting it to a main router which is connected to the ISP.

View 1 Replies View Related

D-Link DAP-1522 Wireless - Create Access Point Password?

Mar 3, 2013

i cant create dlink acess point password , if I am going 192.168.0.50 then showing error massages , I am check two three computer , then the same error coming

View 1 Replies View Related

D-Link DIR-655 :: Using As Wireless Repeater / Access Point / Bridge To Connect

Apr 12, 2011

I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?

View 1 Replies View Related

D-Link DSL-2750U - Connect Wireless Access Point To Modem

Jul 7, 2013

At my office we have a wireless modem(D-Link DSL-2750U) and all the clients are connect to it wirelessly with a wireless lan card. at the next floor we have two pc(without wireless lan card) that I want to connect them to this network, I have a switch and a wireless access point(TP-Link TL-WA701ND). my Question is that how can I connect the WAP to Modem? I set the operation mode of WAP to client and add the MAC address of it in the table of wireless modem but the clients cant connect to the network.

View 1 Replies View Related

TP-Link Dual-Band Wireless :: How To Configure N750 As Access Point

Dec 5, 2012

Region : UnitedStatesModel : TL-WDR4300Hardware Version : V1Firmware Version : 3.13.23 Build 120810 Rel 44064nHow do I configure the TP-Link N750 wireless router model TL-WDR4300 as an access point so that computers/nodes on the WAN, LAN and wifi connections of this device are all on the same network/subnet?From the admin browser page, disabling DHCP and NAT does not provide the desired results.

View 10 Replies View Related

TP-Link 150Mbps Wireless :: WR702N - How To Create Access Point For Printing

Mar 5, 2013

Region : United Kingdom
Model : TL-WR702N
Hardware Version : V4.20.0
Firmware Version :
ISP :

Using a TL-WR702N router as a wireless access point on a narrow-boat. How to print from my i Pad and iPhone to a printer on my narrow-boat, on the UK inland waterways. The Apple store geniuses seem to contradict each other on how it can be done, if at all. I have an i Pad and iPhone and would like to print photos, documents and the occasional web page to my Canon MG4250 printer, which has Air print capability, while I am cruising. I don't have a PC on the boat and of course there is no telephone or broadband connection (other than via 3G on my iPhone). In other words, I want to link my printer to a router, then when required, wireless connect to the router to print from my Apple devices.

Will the TP Link TL-WR702N 150Mbps Wireless N Nano Router allow me to do this? Reading the product information, this nano router looks very flexible, but all five modes mentioned seem to utilize an internet connection. I only have an internet connection via 3G on my iPhone, and can also tether the i Pad to the iPhone's WiFi hotspot to give internet connection on the i Pad. Would I have to use this internet connection somehow, or can I just connect the Apple devices to the printer via the WiFi on the nano router?

In effect I want to create a wireless access point for printing, without any, or at least a regular, internet connection.

View 4 Replies View Related

Cisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point

Apr 20, 2012

I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.

View 4 Replies View Related

Access Point Or Wifi Signal Booster / D-link Wireless N Gigabit Router

Jan 2, 2013

Got 1 Linksys WRT54G Router on the ground floor which uses PTCL DSL Internet and 1 D-Link Wireless N Gigabit Router on the first floor which uses World Call Cable Internet of my house. So yeah we have two internet connections.Getting weak signals from both of the routers in my room on the far left side of the house and little to no signals in the basementSo what I want to ask is that should I purchase better routers or should I go with a signal booster of some sorts like an Access Point or a Range Extender?Also is there such a device which would catch signals from both of these differently configured routers ( different internets, different wireless security keys etc ) and then boost them throughout the house if placed in an area where both the router signals are strong?

View 5 Replies View Related

TP-Link 300Mbps Wireless N Access Point Wireless Key Recovery?

Jul 2, 2012

I am connected to my TP-Link Wireless N AP via wireless on my laptop. The AP is set to the Wireless AP config but I have forgotten the wireless key i defined when i configured Wireless AP, so therefor cannot successfully connect any other device to the network. The key has been saved on the computer its connected to via wireless (my laptop) and I was wodering if i could use this fact or any other method of recovering the key? I am using Win Vista on this system.

View 3 Replies View Related

Connecting Tp-link Wa901nd Access Point As Repeater Without Access To Router

Oct 21, 2012

I have just moved into a new apartment that has a free wifi connection the problem is that my apartment is in the basement at the completly opposite side of the office and i cant get a strong enough signal to connect to the internet and im not very good with computers. the first time i tride setting up the repeater i was able to connect everything and get online but it had changed the ssid and when i tride to change it bacck to its origanil name i lost my internet connection and have not been able to get access the internet again.

Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: AMD Duron(tm) processor, x86 Family 6 Model 8 Stepping 1
Processor Count: 1
RAM: 479 Mb
Graphics Card: S3 Graphics ProSavageDDR (Microsoft Corporation), 32 Mb
Hard Drives: C: Total - 24385 MB, Free - 3678 MB; D: Total - 13776 MB, Free - 13649 MB;
Motherboard: , KM266-8235
Antivirus: None

View 3 Replies View Related

D-link Dir-615 :: Wifi Access Point - Getting No Browser Internet Access

Apr 22, 2013

I've been following those instructions to set a dir-615 as a wifi access point connected to a switch : [URL]. I am now able to connect to the 615 either by wifi or by typing it's ip address with another computer connected to the LAN. Connecting to the 615 by wifi, i can do a ping request to urls or receive and send mail with my e-mail client but i can't access websites using my browser.s it possible to get it working without installing some kind of modified firmware? I tried plugging the Internet ethernet cable in the LAN and Internet ports of the 615, none works.

View 3 Replies View Related

Home Network :: TP-Link Wireless Access Point / Ethernet Switcher (TL-SF2005D) Fails To Connect?

Jun 6, 2011

I have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.

Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.

View 9 Replies View Related

D-Link DIR-655 :: How To Access Setup Window When Used As Access Point

Jul 3, 2011

I have have my Dir-655 set up as an access point for awhile and would like to change the wireless access code. I can't seem to figure out how to access the setup menu while it is an access point to do this. How I access the router when it is set up as an access point?

View 4 Replies View Related

D-Link DIR-655 :: Using As Access Point From TP-Link TL-R860?

Jan 2, 2013

Im trying to use my DIR 655 as an access point from my new router, which is a TP-Link TL-R860. I've read about every post and blog I can find about this and still cant get it to work. Currently I have a cable running from the TP main router to LAN port 1 on the 655. I then plugged my computer in to LAN port 2 to configure the router.

View 14 Replies View Related

D-Link DIR-655 :: How Can It Be Used As Access Point

Jun 12, 2011

I changed the router IP of 192.168.1.1 to 192.168.1.2, and disabled the DHCP.  But I cannot access the DIR655 at the above new address by a browser. Note that the existing router's IP is 192.168.1.1 which the DIR655 is going to be cascaded with.

View 6 Replies View Related

D-Link DIR-655 :: Use Only As An Access Point

Mar 23, 2011

Using dir655 model for access point alone? I want to take the routing part out of this device since it is not needed at this point.

View 3 Replies View Related

D-Link DIR-655 :: Set Router As Access Point?

Apr 24, 2012

I  want to  set D-Link DIR 655  as  Access Point. For your information , I'm using D-Link 2750U (modem + router) as primary wireless router. how do I set D-Link DIR 655  as  Access Point ?

View 5 Replies View Related

D-Link DIR-655 :: Set As Access Point Or Bridge?

May 8, 2011

I like the ease and price of the 655 as well as the range and speed.  I was wondering if you can use them as a bridge to connect another building or just add a second as an access point? It does not seem straightforward from the control panel.

View 14 Replies View Related

D-Link DIR-601 :: Using It As Access Point For Xbox 360

Jan 7, 2012

I've moved into a new apartment with a couple of people who already have wifi set up.  They are adament about me not running a ethernet cable across the apartment to my room for my xbox 360.  I have a DIR-601 from my last apartment, and I am wondering if there is a way to set up the router as an access point that allows me to connect to the existing wifi network and then wire my xbox 360 in. 

View 4 Replies View Related

D-Link DIR-655 :: Optimizing As Access Point?

Nov 14, 2011

I just moved into a new appartment and my buddy next door and I are sharing a connexion using a 2wire router (comes with the internet connexion by the company, with their own firmware).

Now, since the 2wire router signal doesn't perform well, I set up my DIR-655 as an Access point.

Now I would like to know what are the optimal settings for a better signal, and also speed. I rather have stability by wifi g/n mixed (maybe will go n only soon).

Some extra questions;

- Should I deactivate the firewall on my DIR655 to gain speed? I imagine it isn't really usefull since there is already another main router.

- Should I check or uncheck "Short GI", "WMM Enable" and "Extra Wireless Protection"?

- Should I activate or deactivate QoS engine and WISH since it is an acess point to gain speed?

- The firmware on the DIR655 is actualy 1.21, is their a newer and stable firmware I should upgrade to?

View 4 Replies View Related

D-Link DIR-655 :: Use Old Router As An Access Point?

May 28, 2011

I have a D-Link DIR-655 with an usb dongle DWA-140. I used to work with a Sitecom WL-341 router.I want to use the Sitecom WL-341 as an acces point to improve my wireless range at the top floors of my house.

What I want to create:

- The modem connects to the D-Link router;

- The D-Link router makes a wireless connection with the Sitecom router;

- The Sitecom router is now an acces point;

- I connect the Sitecom router with a cable or wireless to my desktop PC.

I don't want a cable in my house that connects the D-Link with the Sitecom. If I do this, not only will people get hurt getting up the stairs because of the cable lying there, it also isn't a pretty sight...

View 1 Replies View Related

D-Link DIR-615 :: Useable As Access Point?

Nov 18, 2012

I want to use my DIR-615 as an access point. But i dont find the button "activate as access point". This button is shown in this Dlink DIR-300 manual url....Is this for spezial hardware only?

View 1 Replies View Related

D-Link DIR-601 :: Remote Connect Through Access Point?

Oct 8, 2011

I have set up an access point as per the instructions I found on this site. It works perfectly, holds a wireless signal fine.  Now, I have the challenge of trying to remote connect to the home computer that is connected to this access point.  I have absolutely no clue as to what changes in settings have to be made.

View 4 Replies View Related

D-Link DIR-655 :: Using Router As Pure Access Point?

Apr 4, 2012

I have a DIR 655 which I am trying to use as a pure access point for a network based on a Comcast SMC  Modem/Router   On the DIR 655 I have the DHCP turned off and on the Internet Connection I have given the DIR 655 a static  address of 10.1.10.2  with Gateway and Primary DNs 10.1.10.1 (The SMC is 10.1.10.1)  I have the DIR 655 connect to the SMC Lan  to Lan.   DIR 655 is G only to deal with and IPAD issue....

The wireless devices get an internet connection BUT...  I can only contact the DIR 655 wirelessly   the SMC does not show the DIR 655 as connected I can not ping the DIR-655 from the SMC.   I can " see" the static addresses I have given to two network cameras  but they don't not respond to Port Forwarding I have assigned at the SMC  (that is more for info as I realize that might be a SMC issue) . How to make the DLIK visable to the wired network.

View 14 Replies View Related

D-Link DIR-655 :: Configuring It As Secondary Access Point?

Sep 15, 2009

I have a DLG-4500 router as my primary router and want to connect a second router (DIR-655) to it as an extention of the LAN to the second floor of my home. I have found instructions on doing this with most other routers, but not DLINK.  In fact when doing the initial configuration and trying to disable the WAN link on the second router by using a bogus IP address string (127.0.0.1) The router won't let me save the change?  What are the steps for configuring a secondary router cascaded to the primary (both wireless) to extend network coverage.

View 13 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved