D-Link DIR-655 :: Access Point Stops Broadcasting Wireless?
Dec 13, 2011
I have two DIR-655s. One is my main router, connected to my modem. The other, on the other side of the house, is set up as an access point. I followed this guide to set up my AP: [URL]
Both are are hard wired. I have both of them using the same SSID. Both are 802.11g only, have the same security mode, and key. The only wireless difference is the channel. One uses 6, while the other uses 11.
On initial setup, everything is fine, but after a few hours, the AP just seems to stop broadcasting a signal. I'm using "Wifi Analyzer" on Android to monitor it. When I look at the AP, the wifi indicator light is still on. If I log into it, change the channel, and press save on the "Wireless Settings" screen, it will broadcast for a few more hours before stopping again. The wired connect of this AP always seems to work (Xbox is hard wired to it).
AP Hardware Version: B1 / Firmware Version: 2.03NA
View 14 Replies
ADVERTISEMENT
Oct 1, 2011
i have 2 DIR 615 routers which both stop broadcasting SSIDS. Ive had only one connected at a time, thinking it was a bad router, but both behave the same way. Is this a known issue or something ? What happens is, after some time (it varies..sometimes 3hours..sometimes longer), the router stops broadcasting the ssid, and I can no longer connect any of my wireless devices to it. The hardwired connection does work (I have a server connected to it, and it appears to work).The only settings I have changed is my SSID name, and wpa2 password. I've set up one virtual server to port forward requests to the server. Thats it. Nothing complex or anything. And both routers behave the exact same way, meaing they stop broadcasting the SSID.
View 8 Replies
View Related
Jun 20, 2011
I bought a DIR-655 (F/W v. 2.00NA) about 6 months ago. It worked well until a couple of weeks ago. Then it started to stop broadcasting WIFI signal without apparent reason. When it did so, I could still connect to it and internet with wired connection, but the WIFI scan does not show my SSID. If I reboot it (either through the admin interface, or just disconnect and reconnect the power), I would be able to reconnect to WIFI, but then WIFI will stop working again in about 8-10 hours. I am rebooting this thing 2-3 times a days and it is very frustrating. Curiously, I borrowed a N300 router to try out
View 10 Replies
View Related
Mar 30, 2011
I just bought a dlink 655 from amazon and for some reason the router stops broadcasting on wifi. I cannot connect to it through my laptop or ps3. The only thing that fixes this is removing the plug from the back of it and putting it back in, once i do this, the SSID shows up once again and all is well until the next day (or 2 days after)
View 2 Replies
View Related
Mar 12, 2008
I the only one who's WRT160N occasionally just stops broadcasting WiFi and have to reset the router to get it back?
View 9 Replies
View Related
Nov 10, 2011
The wireless drops specifically from my laptop constantly at random times. When the wireless drops in order for me to be able to reconnect i have to restart the router itself. There are also random times where the Wi-Fi stops broadcasting altogether. I have a computer connected via Ethernet and it does not lose connection during these times. All the computers are running Windows 7 and the Router is up to date on firmware.
View 5 Replies
View Related
Sep 30, 2011
I have a linksys WRT54G that has been bugging out a lot. It stops broadcasting the SSID briefly and won't start again until it reboots. Annoying enough problem on it's own, but not my primary concern.My concern now is that when I tried to upgrade the firmware to the latest version (which I presume was causing the problems) the router now is essentiallyunresponsive. The upgrade was successful according to the control panel site, but ever since the required reboot as part of the upgrade process the router hasn't worked properly. 1) The power light blinks constantly rather than staying lit.2) When I plug directly into it sometimes I get access to local networks and other times I don't (limited connectivity). But I never get access to the internet if it's plugged into it as well.3) When I try to go to the control panel site (through the 192.168.1.1) the site wont loadGranted this router is old, but it was working fine other than dropping the broadcast every once in a while. It did need a firmware upgrade, but the upgrade seems to have been a bad choice
View 3 Replies
View Related
Mar 19, 2013
My F5D8231-4 (N1 Wireless Router) keeps shutting down its wireless broadcast. If I reset back to factory settings it comes back on but then I have to setup again.
View 1 Replies
View Related
Feb 2, 2012
Currently have a sbs2003 with 2 nics want to install a wireless access point for the internal network. the wireless router is on the external wan how do i link the access point to this?
View 1 Replies
View Related
Jun 11, 2011
So, in an attempt to improve my signal in my house I relocated my router upstairs from downstairs by running a long cable to the modem downstairs, since I have read that the signal travels more efficiently down than up apparently. That has not been the case. Now, I have two routers. A D-link DIR-655 and a Netgear router provided by Comcast which is a WNR-1000v2.
possible to set one of these routers up as a wireless access point? Have a router upstairs be the access point, and have a router downstairs connected to the modem. This sounds like this may be a solution but let me know if I'm completely wrong. In my mind, what I'm after is more of a range extender or a repeater but at this point I don't know the difference anymore. It's been quite stressful dealing with my old man for the past week because he can't use his iPad.
View 3 Replies
View Related
Mar 14, 2013
I'm using Windows 7 with a TP Link router and an RCA cable modem. I only have a laptop and I had it set up so I had wireless on it, and was able to get wireless on my smartphone as well. All of a sudden the wireless stopped working and now I can only connect to the internet with the router plugged in to my laptop. I just updated my wireless driver and have tried the 192.168.0.1 thing so many times and nothing seems to work. I also exchanged my router for a new one and that worked for about a week and then stopped working again. This happened once before and it didn't work for a couple days and then I woke up one morning and it worked again.
View 14 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Nov 5, 2012
A friend of mine has a network with the following setup: D-Link DSL-2500U for ADSL, connected straight into a Telkom DG834GUv5 (locally rebadged Netgear) which has 2 PCs connected via cable, and 2 laptops via Wireless. A cable runs from the Telkom into a standard IPLink switch, which merely extends a cable into a D-Link DIR-615 running DD-WRT that has 2 computers connected, and shares wireless to a couple laptops.
At the moment the network is somewhat unstable, and recently the Telkom router has been giving serious problems, even after resetting to default. I want to try make the network a bit simpler and more stable. Firstly, I want to remove the IPLink switch, which merely extends the cable. Is an Ethernet Coupler what I need? Both cables are definitely under 100m combined (probably under 50m).
Now the big thing is a replacement for the Telkom (rebadged NetGear). Should I get another D-Link DIR-615 or is there a better solution? Their budget is between $40 and $60 US. Is it best to stick to the same brand, considering both devices are D-Link at present?
View 1 Replies
View Related
Oct 25, 2011
I bought a DIR-655 about 8 months ago. I had no problems connecting to the internet for the first couple of months. Then I would get a random connection problem where I would reset my modem or the router and all would be fine for a while. Then about a month and a half ago it started getting worse and worse and about 3 weeks ago it got to a point that I was resetting the router or modem daily to get a initial connection to the internet. And that would last until the next day when we would try to access the internet. Ocassionally, if I had a good initial connection, I would get a random loss of the connections a minute or two after I started surfing the web. Initially a modem or router reset would clear this up too. This happening both over wireless and through the hard wired connection. So it doesn't matter how I am using the Router. AND, most recently resets may not even get me a solid connection to the internet. So, I have bypassed the router for now.
The router was set up with changes to only passwords, network name, a changed router IP address and not broadcasting the wireless it has worked fine. After the reset, I left the router IP address as the default but changed the above security settings. Nothing else was changed. I have never had any issues logging into the router menus through the default or my defined IP addresses.
In doing some troubleshooting, I performed a reset on the modem several times, none of which resolved the problem, I was still losing the connection. Then I bypassed the router and did a direct connection to the modem and all is good and I have not had a connection issue since. I even tried changing the Ethernet connection on the back of the home computer to a different computer port but that changed nothing. I am currently trying a different cable. I am using the standard connection scheme:Cable from outside to modem, modem to router via Ethernet into the proper router port, Router to static computer via Ethernet. And a laptop accesses through the wireless. All cables have been working fine and are home built CAT 5e cables
It is really frustrating and I am not sure where to start now. Currently, I am running without the router for internet but I need it for the wireless to a laptop in another room. I use Time Warner Cable and have a Atlantic Scientific DPC2100 cable modem.
View 5 Replies
View Related
Aug 31, 2011
So I've decided to use a different router to resolve some VPN issues, and want to use my DIR-655 as a pure wireless access point. I need the access point to use the same range of IP addresses as the rest of the network (maintain access to networked printers, file shares, etc). However, I can't establish a wireless connection to the access point.
- Defined a IP address for the DIR-655 within the DHCP range of the primary router
- Defined the proper subnet
- Disabled the DHCP server on the DIR-655
- Connect a LAN port of the DIR-655 to a LAN port on a switch (note that it's not connected directly to a router).
When I connect a device WIRED to a LAN port on the DIR-655, everything works fine. The device gets assigned a DHCP address (which I know is being assigned by the main router since the DIR-655 DHCP server is disabled), and I can connect to the LAN and I can access the internet with no problem. So I know the DIR-655 is acting correctly to pass thru traffic. Also, I can access the DIR-655 web configuration page from any LAN device (even a device not directly connected to the DIR-655), so I know the DIR-655 is on that LAN correctly.
But when I try to connect WIRELESS to the DIR-655, it doesn't work at all. Although the wireless NIC is connecting to the DIR-655 (e.g. it asks me for the WPA key), it can't pull an IP address, so there is no connection to the LAN or internet.
View 5 Replies
View Related
Jun 4, 2011
So just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.
View 1 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Nov 20, 2011
How can I configure my TP-Link router TD-W8950ND act as an access point? I'll be connecting it to a main router which is connected to the ISP.
View 1 Replies
View Related
Mar 3, 2013
i cant create dlink acess point password , if I am going 192.168.0.50 then showing error massages , I am check two three computer , then the same error coming
View 1 Replies
View Related
Apr 12, 2011
I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
View 1 Replies
View Related
Jul 7, 2013
At my office we have a wireless modem(D-Link DSL-2750U) and all the clients are connect to it wirelessly with a wireless lan card. at the next floor we have two pc(without wireless lan card) that I want to connect them to this network, I have a switch and a wireless access point(TP-Link TL-WA701ND). my Question is that how can I connect the WAP to Modem? I set the operation mode of WAP to client and add the MAC address of it in the table of wireless modem but the clients cant connect to the network.
View 1 Replies
View Related
Dec 5, 2012
Region : UnitedStatesModel : TL-WDR4300Hardware Version : V1Firmware Version : 3.13.23 Build 120810 Rel 44064nHow do I configure the TP-Link N750 wireless router model TL-WDR4300 as an access point so that computers/nodes on the WAN, LAN and wifi connections of this device are all on the same network/subnet?From the admin browser page, disabling DHCP and NAT does not provide the desired results.
View 10 Replies
View Related
Mar 5, 2013
Region : United Kingdom
Model : TL-WR702N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Using a TL-WR702N router as a wireless access point on a narrow-boat. How to print from my i Pad and iPhone to a printer on my narrow-boat, on the UK inland waterways. The Apple store geniuses seem to contradict each other on how it can be done, if at all. I have an i Pad and iPhone and would like to print photos, documents and the occasional web page to my Canon MG4250 printer, which has Air print capability, while I am cruising. I don't have a PC on the boat and of course there is no telephone or broadband connection (other than via 3G on my iPhone). In other words, I want to link my printer to a router, then when required, wireless connect to the router to print from my Apple devices.
Will the TP Link TL-WR702N 150Mbps Wireless N Nano Router allow me to do this? Reading the product information, this nano router looks very flexible, but all five modes mentioned seem to utilize an internet connection. I only have an internet connection via 3G on my iPhone, and can also tether the i Pad to the iPhone's WiFi hotspot to give internet connection on the i Pad. Would I have to use this internet connection somehow, or can I just connect the Apple devices to the printer via the WiFi on the nano router?
In effect I want to create a wireless access point for printing, without any, or at least a regular, internet connection.
View 4 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Jan 2, 2013
Got 1 Linksys WRT54G Router on the ground floor which uses PTCL DSL Internet and 1 D-Link Wireless N Gigabit Router on the first floor which uses World Call Cable Internet of my house. So yeah we have two internet connections.Getting weak signals from both of the routers in my room on the far left side of the house and little to no signals in the basementSo what I want to ask is that should I purchase better routers or should I go with a signal booster of some sorts like an Access Point or a Range Extender?Also is there such a device which would catch signals from both of these differently configured routers ( different internets, different wireless security keys etc ) and then boost them throughout the house if placed in an area where both the router signals are strong?
View 5 Replies
View Related
Jul 2, 2012
I am connected to my TP-Link Wireless N AP via wireless on my laptop. The AP is set to the Wireless AP config but I have forgotten the wireless key i defined when i configured Wireless AP, so therefor cannot successfully connect any other device to the network. The key has been saved on the computer its connected to via wireless (my laptop) and I was wodering if i could use this fact or any other method of recovering the key? I am using Win Vista on this system.
View 3 Replies
View Related
Oct 21, 2012
I have just moved into a new apartment that has a free wifi connection the problem is that my apartment is in the basement at the completly opposite side of the office and i cant get a strong enough signal to connect to the internet and im not very good with computers. the first time i tride setting up the repeater i was able to connect everything and get online but it had changed the ssid and when i tride to change it bacck to its origanil name i lost my internet connection and have not been able to get access the internet again.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: AMD Duron(tm) processor, x86 Family 6 Model 8 Stepping 1
Processor Count: 1
RAM: 479 Mb
Graphics Card: S3 Graphics ProSavageDDR (Microsoft Corporation), 32 Mb
Hard Drives: C: Total - 24385 MB, Free - 3678 MB; D: Total - 13776 MB, Free - 13649 MB;
Motherboard: , KM266-8235
Antivirus: None
View 3 Replies
View Related
Apr 22, 2013
I've been following those instructions to set a dir-615 as a wifi access point connected to a switch : [URL]. I am now able to connect to the 615 either by wifi or by typing it's ip address with another computer connected to the LAN. Connecting to the 615 by wifi, i can do a ping request to urls or receive and send mail with my e-mail client but i can't access websites using my browser.s it possible to get it working without installing some kind of modified firmware? I tried plugging the Internet ethernet cable in the LAN and Internet ports of the 615, none works.
View 3 Replies
View Related
Jun 6, 2011
I have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.
Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.
View 9 Replies
View Related
Jul 3, 2011
I have have my Dir-655 set up as an access point for awhile and would like to change the wireless access code. I can't seem to figure out how to access the setup menu while it is an access point to do this. How I access the router when it is set up as an access point?
View 4 Replies
View Related
Jan 2, 2013
Im trying to use my DIR 655 as an access point from my new router, which is a TP-Link TL-R860. I've read about every post and blog I can find about this and still cant get it to work. Currently I have a cable running from the TP main router to LAN port 1 on the 655. I then plugged my computer in to LAN port 2 to configure the router.
View 14 Replies
View Related
Nov 13, 2011
I have a DIR-615 Wireless N D-Link router. Simple setup, comcast cable modem ---> router ---> wireless signal to house. For some reason, kinda out of nowhere (can't recall precisely when it began doing this) the router is broadcasting 2 SSID's, one is my configured network, and another network named: D-Link_Wireless. Whats strange thou, is that some devices detect the D-Link_Wireless SSID and others do not. When I go into the router config, all I see is the one configured network, PanzerNet. I wouldn't care so much but I think it's causing some conflictions with my DNS address, making me have to constantly reset my router..
View 14 Replies
View Related
Jun 12, 2011
I changed the router IP of 192.168.1.1 to 192.168.1.2, and disabled the DHCP. But I cannot access the DIR655 at the above new address by a browser. Note that the existing router's IP is 192.168.1.1 which the DIR655 is going to be cascaded with.
View 6 Replies
View Related
