Wireless :: Configure TP-Link Router TD-W8950ND Act As An Access Point?
Nov 20, 2011How can I configure my TP-Link router TD-W8950ND act as an access point? I'll be connecting it to a main router which is connected to the ISP.
View 1 Replies
ADVERTISEMENT
TP-Link Dual-Band Wireless :: How To Configure N750 As Access Point
Dec 5, 2012Region : UnitedStatesModel : TL-WDR4300Hardware Version : V1Firmware Version : 3.13.23 Build 120810 Rel 44064nHow do I configure the TP-Link N750 wireless router model TL-WDR4300 as an access point so that computers/nodes on the WAN, LAN and wifi connections of this device are all on the same network/subnet?From the admin browser page, disabling DHCP and NAT does not provide the desired results.
View 10 Replies View RelatedTP-Link ADSL2+ Wireless :: TD-W8950ND Modem Router To Stop Dhcp / Dns Provided By Device
Apr 9, 2013Region : Australia
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.2.9 build 110212 Rel.22296n
I made some changes on my wireless modem router to stop dhcp and dns provided by my device. A server is now doing it, but at the same time I appear to have connection issues where I didn't before. In an attempt to resolve the issues I looked at the System Log and a number of things were coming up that concerned me. These are as follows:
-user: tr69c: Unable to retrieve attributes in scratch PAD
-user: Stored Parameter Attribute data is corrupt or missing
Additionally I'm getting a lot of kernel: Intrusion alerts which I can't determine how serious they are. Where to start tracking down these issues (if they even warrant investigation).
D-Link DIR-601 :: Configure In Bridge Mode As An Access Point?
Aug 23, 2011My apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies View RelatedCreate A Static Route On The TP-Link TD-W8950ND Router?
Jan 26, 2011I am trying to create a static route on the TP-Link TD-W8950ND router, however am a little confused about the interface I should use. The default gateway on the route is another router on the LAN. I have a choice to use interface pppoe (telstra), LAN/br01 (bridge) or no interface. I was assuming I didn't need to use any interface as this is not a bridge setup and is on the LAN, but when I select "no interface" it doesn't save the static route settings.Also, when I select LAN/br01, the routing saves but doesn't actually work (tracert shows not going through the right router).
View 1 Replies View RelatedHow To Configure A Router To A Wireless Access Point
Apr 17, 2011am trying to find the configuration code and steps to configure a router to a wireless access point.
View 2 Replies View RelatedHow To Configure Wireless Access Point To Linksys Router
Jan 18, 2011How do I configure my Linksys N Router for a Netgear Wireless N Access Point set in repeater mode? Linksys and Netgear are communicating, but no Internet access is available on Netgear which makes me think I need to configure Linksys to provide Internet connectivity to the Netgear access point repeater.
View 1 Replies View RelatedLinksys Wireless Router :: How To Configure WRT400n As An Access Point
Aug 13, 2009I would like to configure it as an access point on my LAN, similar to the way my WAP55AG works.My research on the Internet and on these forums indicate that I have to disable DHCP on the router as well as use the LAN ports to connect it to my network.I am able to turn off DHCP, but assigning it a static IP address is challenging.I can set the IP address, but I am unable to set the subnet mask to 255.255.254.0 as I am only getting a set of SM in a drop down list whick are all 255.255.255.x
View 9 Replies View RelatedLinksys Wireless Router :: Configure E1550 As An Access Point?
Nov 8, 2011how to access an E1550 wireless router's settings and configure it to connect to my wireless DSL router? The DSL phone line is not located anywhere near my TV/DVR/Roku and I'd like to connect them wirelessly to our DSL router. The E1550 is next to the TV/DVR/Roku.
View 6 Replies View RelatedTP-Link ADSL2+ Wireless :: IPSec VPN Tunnel Between TD-W8950ND And RV082?
Dec 21, 2012Region : Others
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.3.1 build 120406 Rel.32903n
ISP : PTCL
I am trying to establish IPSec VPN Tunnel between Linsys RV082 and TP-Link TD-W8950ND but failed.
Linksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedLinksys Wireless Router :: Configure Access Point As Repeater For 2.4 GHz Band On WRT610N?
Jun 22, 2010I'm very dissatisfied with the range and signal strength of my new WRT610N dual band router compared to the WAP54G Access Point I used before.Can I configure the Access Point as a repeater for the 2.4 GHz band on the WRT610N if I use the WRT610N as a Wireless G router rather than wireless N?
View 5 Replies View RelatedRouting On TP-Link TD-W8950ND?
Jan 26, 2011I am trying to create a static route on the TP-Link TD-W8950ND router, however am a little confused about the interface I should use. The default gateway on the route is another router on the LAN. I have a choice to use interface pppoe (telstra), LAN/br01 (bridge) or no interface. I was assuming I didn't need to use any interface as this is not a bridge setup and is on the LAN, but when I select "no interface" it doesn't save the static route settings.Also, when I select LAN/br01, the routing saves but doesn't actually work (tracert shows not going through the right router).
View 4 Replies View RelatedCisco WAN :: 3845 / How To Configure Vrf For Point To Point Link
Mar 11, 2013i have cisco 3845 router,how to configure vrf for point to point link .
View 1 Replies View RelatedD-Link DIR-615 :: New Wireless Router / Access Point
Nov 5, 2012A friend of mine has a network with the following setup: D-Link DSL-2500U for ADSL, connected straight into a Telkom DG834GUv5 (locally rebadged Netgear) which has 2 PCs connected via cable, and 2 laptops via Wireless. A cable runs from the Telkom into a standard IPLink switch, which merely extends a cable into a D-Link DIR-615 running DD-WRT that has 2 computers connected, and shares wireless to a couple laptops.
At the moment the network is somewhat unstable, and recently the Telkom router has been giving serious problems, even after resetting to default. I want to try make the network a bit simpler and more stable. Firstly, I want to remove the IPLink switch, which merely extends the cable. Is an Ethernet Coupler what I need? Both cables are definitely under 100m combined (probably under 50m).
Now the big thing is a replacement for the Telkom (rebadged NetGear). Should I get another D-Link DIR-615 or is there a better solution? Their budget is between $40 and $60 US. Is it best to stick to the same brand, considering both devices are D-Link at present?
Linksys Access Point :: Configure WRT120n As An Access Point?
May 1, 2012Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedHow To Configure Linksys Router Wtr120n As An Access Point
Jan 14, 2012I have a linksys wireless-N router model number is WRT120N and I need to use it as an access point. How i can do that?
View 1 Replies View RelatedHow To Configure Wireless Access Point
Jun 13, 2011I want to know how to configure wireless access point because i got new internet connection in my home i want to share connection with my nighbour so we bring TP-Link wireless access point bought one cable wire connect with switch and another one connect with TP-LINK access point, but it is not working .now we dont know how it will be work.
View 2 Replies View RelatedRouters / Switches :: Configure SpeedTouch Router As Access Point?
Nov 5, 2011i have a LAN network between several pc's connected with several switch's and connected to Thomson SpeedTouch 510 DSL Router its ip address is 10.0.0.100 subnet 255.0.0.0 and the router dont give auto ip to the PCs i have to issign it manually to the PCs "static ip".I bought the acer android recently so i bought a tp-link td-w8901g wireless router to act as an access point so i connected the 2 routers to each other by LAN and gave the tp-link an ip address 10.0.0.12 subnet mask 255.0.0.0 so it will be the same ip range of the speedtouch and setuped the tp-link router to fit my isp configeration it worked at first but i had to reset the router so i did the same configuration i did before but didnt work and i cant access the internet using the android or the wireless but when i connect the phone to the tp-link and unplug the speedtouch the wireless works so theres no any problem with the router?
View 1 Replies View RelatedCisco WAN :: 887 - Configure ISR Wireless Access Point?
May 21, 2011I am trying to configure Cisco 887-W ISR but have hit a stumbling block when trying to configure the wireless access point- or at least the advanced features of the access point using the URL referenced in from the cisco GUI configuration utility (Cisco Configuration Professional ). I do recall previously reading a post which referenced a different URL.
View 2 Replies View RelatedCisco Wireless :: 1024N To Configure Access Point
Oct 25, 2012I am attempting to configure a Aironet 1042N AP From my understanding it does not have an IP out the box. I attempted to access the console which I can view it booting up but then it hangs on.
View 1 Replies View RelatedAccess Point Or Wifi Signal Booster / D-link Wireless N Gigabit Router
Jan 2, 2013Got 1 Linksys WRT54G Router on the ground floor which uses PTCL DSL Internet and 1 D-Link Wireless N Gigabit Router on the first floor which uses World Call Cable Internet of my house. So yeah we have two internet connections.Getting weak signals from both of the routers in my room on the far left side of the house and little to no signals in the basementSo what I want to ask is that should I purchase better routers or should I go with a signal booster of some sorts like an Access Point or a Range Extender?Also is there such a device which would catch signals from both of these differently configured routers ( different internets, different wireless security keys etc ) and then boost them throughout the house if placed in an area where both the router signals are strong?
View 5 Replies View RelatedConnecting Tp-link Wa901nd Access Point As Repeater Without Access To Router
Oct 21, 2012I have just moved into a new apartment that has a free wifi connection the problem is that my apartment is in the basement at the completly opposite side of the office and i cant get a strong enough signal to connect to the internet and im not very good with computers. the first time i tride setting up the repeater i was able to connect everything and get online but it had changed the ssid and when i tride to change it bacck to its origanil name i lost my internet connection and have not been able to get access the internet again.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: AMD Duron(tm) processor, x86 Family 6 Model 8 Stepping 1
Processor Count: 1
RAM: 479 Mb
Graphics Card: S3 Graphics ProSavageDDR (Microsoft Corporation), 32 Mb
Hard Drives: C: Total - 24385 MB, Free - 3678 MB; D: Total - 13776 MB, Free - 13649 MB;
Motherboard: , KM266-8235
Antivirus: None
Cisco Wireless :: WAP 4410N Network - Configure One As Access Point And Rest As WDS Bridge / Repeater
Sep 5, 2011I have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies View RelatedD-Link DIR-655 :: Set Router As Access Point?
Apr 24, 2012I want to set D-Link DIR 655 as Access Point. For your information , I'm using D-Link 2750U (modem + router) as primary wireless router. how do I set D-Link DIR 655 as Access Point ?
View 5 Replies View RelatedD-Link DIR-655 :: Use Old Router As An Access Point?
May 28, 2011I have a D-Link DIR-655 with an usb dongle DWA-140. I used to work with a Sitecom WL-341 router.I want to use the Sitecom WL-341 as an acces point to improve my wireless range at the top floors of my house.
What I want to create:
- The modem connects to the D-Link router;
- The D-Link router makes a wireless connection with the Sitecom router;
- The Sitecom router is now an acces point;
- I connect the Sitecom router with a cable or wireless to my desktop PC.
I don't want a cable in my house that connects the D-Link with the Sitecom. If I do this, not only will people get hurt getting up the stairs because of the cable lying there, it also isn't a pretty sight...
D-Link DIR-655 :: Using Router As Pure Access Point?
Apr 4, 2012I have a DIR 655 which I am trying to use as a pure access point for a network based on a Comcast SMC Modem/Router On the DIR 655 I have the DHCP turned off and on the Internet Connection I have given the DIR 655 a static address of 10.1.10.2 with Gateway and Primary DNs 10.1.10.1 (The SMC is 10.1.10.1) I have the DIR 655 connect to the SMC Lan to Lan. DIR 655 is G only to deal with and IPAD issue....
The wireless devices get an internet connection BUT... I can only contact the DIR 655 wirelessly the SMC does not show the DIR 655 as connected I can not ping the DIR-655 from the SMC. I can " see" the static addresses I have given to two network cameras but they don't not respond to Port Forwarding I have assigned at the SMC (that is more for info as I realize that might be a SMC issue) . How to make the DLIK visable to the wired network.
Setting Up TP Link TL-WR941D Router And Access Point?
Oct 1, 2011setting up wifi network in my office. my complete set up right now. the main problem is how to setup my access points . Okay so here it is.
I have 3 - 4 PCS in my office out of which My machine is the main machine and everything is setup on this. so for networking what i have done is i am using a TP link router model TL-WR941D. i had got it configured from an engineer. A cable from my internet modem goes into the blue port of this router(WAN) and my PCs are connected via the LAN port of the router . so everything is working fine right now the local network and internet on all PCS and my laptop also connects through the wifi and is able to access other pcs and also the internet.
To have better signal strength on other floors of the building my engineer had installed 2 access points. They are TP link model Tl-WA901ND. yesterday i updated the firmware of my main router and the settings were some how lost but i managed to set it back to working state using the quick setup utility. so my router and wifi is working fine. But now my access points have stopped sworking . i mean i am not able to get better signal strengths thorugh them. i am assuming theirs ettings /ip etc are lost. now i have no idea how to setup these access points to be used again as part of my wifi network. I looked on the internet but nowhere the thing has been explained in detail. how can i configure my access points/repeaters agaain? i am stuck and engineer is not available for nest few days and my officee internet is suffering.
Turn Tp-link Wifi Router Into An Access Point
Mar 3, 2013I wish to turn my TP-Link wireless router into an access point but can't figure out how to do it. I have tried several times but without any success. Below are my information about my main router and the router I want to turn into an access point:
1- Main Router: TP-LINK 3G/4G Wireless N Router 300Mbps - Model No. TL-MR3420. url..
2- Router I wish to turn into an access point:TP-LINK Wireless N Router 150Mbps - Model No. TL-WR740N. url...
D-Link DIR-655 :: Connecting Linksys Router As Access Point?
Mar 21, 2011My home network currently has a Linksys router (essentially acting as a wireless access point) in a distant part of the house connected to my main router, a Netgear WNR2000, and this configuration is working fine.
I want to replace the main router with a new D-Link DIR-655 (better parental controls). When I swap in the new router and get the cables plugged in in the same manner as they are in the Netgear router, computers connecting wirelessly to the Linksys router can no longer access the Internet.
The Netgear router is set up with an IP address of 192.168.4.1. The Linksys is 192.168.2.1, and the D-Link is at the default 192.168.0.1.
D-Link DIR-655 :: Use Linksys WRT54GL Router As Access Point With It?
Jan 3, 2013I just recently picked up a DIR-655 to replace my WRT54GL, hoping that I could get a better stream in my house. The house is 100 years old with plaster and lathe, and I can't relocate the modem and router. So I figured I could use my old WRT54GL as a signal booster/access point on the second level of the house. I read through a couple of guides, and I could get the router to broadcast the signal with full bars, and I could attach to it, but I didn't get any internet. The D-Link is a DIR-655 with firmware 2.10NA. The Linksys is a WRT54GL with Tomato 1.25. Here are a couple screenshots for the DIR-655
View 1 Replies View RelatedCisco Wireless :: Configure 1310 Point-to-point Bridge (AIR-BRI1310G-A-K9-R)
Apr 24, 2011Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)
View 3 Replies View RelatedWireless :: How To Link Access Point
Feb 2, 2012Currently have a sbs2003 with 2 nics want to install a wireless access point for the internal network. the wireless router is on the external wan how do i link the access point to this?
View 1 Replies View Related