how to access an E1550 wireless router's settings and configure it to connect to my wireless DSL router? The DSL phone line is not located anywhere near my TV/DVR/Roku and I'd like to connect them wirelessly to our DSL router. The E1550 is next to the TV/DVR/Roku.
View 6 RepliesHow do I configure my Linksys N Router for a Netgear Wireless N Access Point set in repeater mode? Linksys and Netgear are communicating, but no Internet access is available on Netgear which makes me think I need to configure Linksys to provide Internet connectivity to the Netgear access point repeater.
View 1 Replies View RelatedI would like to configure it as an access point on my LAN, similar to the way my WAP55AG works.My research on the Internet and on these forums indicate that I have to disable DHCP on the router as well as use the LAN ports to connect it to my network.I am able to turn off DHCP, but assigning it a static IP address is challenging.I can set the IP address, but I am unable to set the subnet mask to 255.255.254.0 as I am only getting a set of SM in a drop down list whick are all 255.255.255.x
View 9 Replies View RelatedI'm very dissatisfied with the range and signal strength of my new WRT610N dual band router compared to the WAP54G Access Point I used before.Can I configure the Access Point as a repeater for the 2.4 GHz band on the WRT610N if I use the WRT610N as a Wireless G router rather than wireless N?
View 5 Replies View RelatedI had previously posted about problems with the E1550 not being able to recognize NTFS formated hard drives. After multiple retries and reformats I was finally able to get it to work and was able to backup my system files to that NTFS hard drive.
Now, little more than a week later I setup to run my backup to run again and once again the E1550 is not accessing the hard drive. The same one it had previously acknowledged and allowed me to save to.
The E1550 sees that there is a hard drive out there but all it says is "Detecting..." this does not change.
I need this to be fixed and stay fixed. If it is going to do this every time I turn on the drive to do weekly backups, then I need to get a different wireless router.
I installed a Linksys E1550 wireless router at home and I moved an external storage drive from the old computer (soon to be gone) to the router via the USB port in the router.
I can see the drive and files on the router on both the old computer and the new laptop, but I can't do anything with them. When I look at permissions for any given file it says: "Everyone" has read and execute only. "root" has Full Control, but I can't gain access to the "root" userid. I have gone through the router setup and folder/file properties using the "admin" userid and the router acknowledges that it is there, but it won't allow me to add permissions for the "admin" with "Full Control" to any of the items.
It won't even allow me to add new files, even though I have setup sharing for the entire partition.
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI have a linksys wireless-N router model number is WRT120N and I need to use it as an access point. How i can do that?
View 1 Replies View RelatedIs it possible to configure WRT120n as an access point?
View 1 Replies View Relatedam trying to find the configuration code and steps to configure a router to a wireless access point.
View 2 Replies View RelatedHow can I configure my TP-Link router TD-W8950ND act as an access point? I'll be connecting it to a main router which is connected to the ISP.
View 1 Replies View Relatedi have just connected my linksys e2000 to the internet now i would like to set it up so other computers can connect to the internet through it wired/ wireless
View 1 Replies View RelatedI dont really have the RJ45 cable, how to configure it as an access point wirelessly? I mean,just by entering the main menu with the default ip address.
View 1 Replies View RelatedI'm trying to access the WAP200 for the first time. Instructions say Configure your PC to have the static IP address on the same subnet as the Access Point's default address (http://192.168.1.245). So I assumed i would go to TCP/IP properties and type in IP address and subnet mask and the Utility would open.
View 3 Replies View RelatedI have a wrt54gx2 with srx 200 technology recently purchased. I havetwo cabled computers attached. One at one end of the house attached tothe router by ehternet cable, the other attached about 100 ft by ethernet cable.The wireless does not reach to the other end of the house, most likley because that part of the house is an addition with masonary walls and a large masonary firplace. I bought a wap54g access point at the recommendation from someone at linksys to attach to the end of the ethernet run. Since my set up is macintosh, I can't use the wizard disk that came with the wap54g. Linksys support was not support( not expected), I need to know what to do to get this up and running. I am new to this stuff and Linksys get the wireless router with ethernet installed and up and running with my dsl. I thought the same for the wap54g.
View 2 Replies View RelatedI just took over a position where I had to reset a WAP54G because no one knew the encryption key. In working with some of the wireless access points in the past, I know that they came with setup or utility software to find and configure. where I can get a copy. I couldn't find it on Linksys' site.
View 3 Replies View Relatedi have 2 linksys modems wag120n and wag320n.i am using wag320n as my primary modem and i want to set up wag120n as an access point to provide internet access in another room. what should be the configuration of wag120n?and yes i have read all the post about this subject and tried it all but since there was no actual solution for this problem i decided to open a new post.
View 1 Replies View RelatedI've read the various threads on here and tried all the fixes suggested and I still cannot get my PS3 to "see" the USB drive I've attached to my router.I can see it and access the files from a connected computer, but not the PS3.I've tried creating a share with one directory and sharing the entire partition with no luck. I've enabled all the FTP options with no luck. UPNP is enabled. I've tried setting up the guest account with no luck.I've tried restarting, unplugging with no luck either. I also went into the USB drive and reformatted and started all over again.My PS3 can easily see the other computers on the network, but I would like to use the USB port on the router to not have to have a computer running to stream music.Is there another menu location on the PS3 I should be using to locate the USB? Currently I just look under music or video and the other computers are there. Just not the USB.
View 1 Replies View RelatedI have a Linksys E1550. I would like to extend its range by using an old Netgear N600 I have laying around. I know the Netgear can be used as a repeater. I do not know what settings I need to change in my Linksys router to be able to use a repeater.
View 5 Replies View Relatedi have a linksys e1550 router and ive been trying to look up a way to make it connect with my nintendo ds lite
View 3 Replies View RelatedI replaced a WRT54G2 V1 with a E1550 earlier this week. This router connects a sub-net of our office to the main network of our office. When the WRT54 was in place everything worked without a hitch, but the E1550 keeps dropping us from a server we have on the main network. The WRT54 is back in play until I can figure this out.
View 1 Replies View RelatedI have a Cisco linksys router e1550. My wireless network is working fine, but my wired (PC) is not working?
Removing the router and having the modem connected to my PC works but when I put on my router my wired connection only works for a few seconds to none
So I think the router may be causing it, could it be the settings? Even though there at default.
I have a E1550 with a corrupt config that is acting very wonky lately (shows wrong info in some of the settings and doesn't always save changes). Since it may be the config that is at issue, I don't want to do a backup/resote, rather I plan to do a full factory reset and manully type everything back in.What would be nice is, creating a text based, human readable printout of the config for reference so that I don't have to manually type it all twice (once to save it, once for reentry). PS3 ports, MAC filters, etc. have several entries, and they way the pages are designed it doesn't allow for easy, whole entry, cut and paste.
View 5 Replies View RelatedI reset my E1550 wireless router with the red button under it. Ever since then I can not connect to internet.
View 3 Replies View RelatedMy objective is to use the USB port on the E1550 to share an external hard drive for my family's shared media files.I have moved into a rental home with little cat5 wiring. Internet service is Uverse.Given the wiring situation, I bought a netgear universal dual band range extender which connects wirelessly to the uverse router in another room. My home office equipment (computer, printer) are wired into the netgear. All of that works fine. The netgear is 192.168.1.66. The computer is 192.168.1.128. So, I wanted to add the E1550 into my network. I can see it as an attached device on the Netgear's admin page, but cisco connect and a direct ip http://192.168.1.68 does not resolve. I have the e1550 connected via a lan port on the netgear extender (there is no other option). I have gone from that lan port to the internet port on the e1550. I have done so with a staight Cat5 cable and with what I believe should be a cross-over. In both situations, I see the router via the netgear admin page but can not connect to it. I'd prefer not the hang my usb drive off of my computer because it if gets turned off or reboots due to a MS Windows auto update, it leaves the rest of the house with no shared media during that process.
View 1 Replies View RelatedI have a Linksys E1550 Wireless Router that is fast as can be on the wired connection, getting 30mbs from the cable modem connection. If I switch to using wireless on the same PC, the max connection speed I'll get is 2mbs. I've changed all sorts of settings trying to get this working right, and it still stays at 2mbs.As an additional note, this router was previously working fine at 30mbs on wireless as well, then out of nowhere this weekend, it started running at 2mbs. I went and purchased another of the same model and it is doing the same thing as well.
What is the secret to having this run at it's correct speed, not this slow 2mbs that it is now? I have configured this the same as every other Linksys router I've had in the past, and it is running horribly slow..I'm on the newest firmware as well, have already verified that. The old router was updated to newest firmware as testing to resolve this, and the new router came with it installed already.
I tried to connect to my E1550 router admin page at 192.168.1.1 and I'm not seeing the login page. I'm getting an error. I've always been able to get to the admin page. I'm not sure what changed. I tried changing the IP# and subnet mask of my laptop and I still can't connect. I tried resetting the router to factory defaults.
View 1 Replies View RelatedE1550 not connecting to any Google related sites via Kindle Fire web application (Silk) in Kindle Fire. Other wireless devices working fine from E1550 and all apps in Fire connecting fine.
View 5 Replies View RelatedI have an E1550 less than 1 year old. Lately, I have been losing internet on the AT&T modem. I called AT&T but as part of their diagnostics, I have to plug the modem directly into the PC. I have loaded the latest firmware to the E1550.Lose Internet but wireless connectivity to router exists.Internet light on modem is out (modem is connected to router)Unplug modem and leave off plug in, internet light is still out.Unplug router, plug router back in - no internet connection but do have wireless connectivity to router.Take cable from modem to router and plug directly into PC internet light comes on in modem and I have internet from PC.Take cable from PC and plug back into router .I have internet via wireless.What I can't figure out is what could be happening in router that would impact modem internet connection. I have replicated this at least 3 times. Yes, the modem is a bit old, but since plugging it directly into the PC works, I'm thinking it has to be the router and I cannot figure out why unless there's some sort of electrical thing going on in the router.
View 4 Replies View RelatedSo, what I essentially want to do is share the device connected to the back of my router so that I can remotely access it over the internet. Much like the manual says you can do.
But I'm having trouble. I've currently got the port set at 38, but the website never loads.
I may be replacing my e1550 soon and am looking at both the N750 and N900 class devices. While the EA3500/4500 seem to be a really good deal with a lot of bang for buck, I do have one concern...
As I have zero intention of ever using Cisco Cloud Connect, I would need to stick with the Classic firmware. While Cisco did quickly push out a solution to get the routers back to Classic after the initial Cloud Connect deployment fiasco, I cannot seem to find any commitment from Cisco to continue to support the classic interface (other than "“Cisco will continue to support both local and cloud management options for our customers.”). Even more disconcerting is that the current evidence seems to indicate that they are not. [code]
So, while I do understand that many of the updates have been Cloud Connect specific, some of these changes are in fact global/driver updates. As an example, according to the release notes, on June 25, 2012 the EA3500 CCC firmware v.1.1.38 (Build 138143) updated the WiFi driver, apparently the Classic never received this update.
I want to know how to configure wireless access point because i got new internet connection in my home i want to share connection with my nighbour so we bring TP-Link wireless access point bought one cable wire connect with switch and another one connect with TP-LINK access point, but it is not working .now we dont know how it will be work.
View 2 Replies View Relatedi have a LAN network between several pc's connected with several switch's and connected to Thomson SpeedTouch 510 DSL Router its ip address is 10.0.0.100 subnet 255.0.0.0 and the router dont give auto ip to the PCs i have to issign it manually to the PCs "static ip".I bought the acer android recently so i bought a tp-link td-w8901g wireless router to act as an access point so i connected the 2 routers to each other by LAN and gave the tp-link an ip address 10.0.0.12 subnet mask 255.0.0.0 so it will be the same ip range of the speedtouch and setuped the tp-link router to fit my isp configeration it worked at first but i had to reset the router so i did the same configuration i did before but didnt work and i cant access the internet using the android or the wireless but when i connect the phone to the tp-link and unplug the speedtouch the wireless works so theres no any problem with the router?
View 1 Replies View Related