How To Configure Linksys E2000 As Access Point
Mar 25, 2011i have just connected my linksys e2000 to the internet now i would like to set it up so other computers can connect to the internet through it wired/ wireless
View 1 Replies
ADVERTISEMENT
Use Linksys E2000 Router As A Access Point?
Mar 13, 2012How can i use Linksys E2000 rounter as a Access point ?
View 1 Replies View RelatedLinksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedLinksys Access Point :: Add Repeater To E2000 System?
Mar 31, 2011I need to extend the wireless range over what I have using an E2000. Can I use a WAP610N in repeater mode? If not can I use a WAP54G knowing that there will be a performance loss? Is there another option to add additional coverage to the existing wireless network?
View 2 Replies View RelatedLinksys Wireless Router :: Using An E2000 As Repeater / Access Point?
Aug 3, 2011We have a wireless network and would like to extend the range for it and I was told that a E2000 could be setup to extend the range.If we say that our existing wireless network has the SSID network1, can the E2000 be setup so that it is connected to a LAN socket and then wok as a wireless runter with the same SSID (network1) so that pc's can connect easily ?Or must the two wireless routers be connected with a dedicated cable ?Or must I setup the new E2000 up as a new wireless network with a new SSID like network2 ?
View 3 Replies View RelatedLinksys Wireless Router :: E2000 Connected To RVS4000 As Access Point
Feb 26, 2012I use a E2000 as a wireless access point to the Internet, by connecting the LAN of the E2000 (set for x.x.x.5) to the LAN of an RVS4000 (Set for x.x.x.1). The E2000 is set for Automatic Configuration, and everything works fine..... Until a power failure occurs... Then, after everything boots up again.. I get the "NO INTERNET" prompt on the wireless....
Â
By using Ping Plotter, from a computer on wireless end, and another computer with Ping Plotter on the wired side of the x.x.x.1 LAN, I've determined that it's the E2000 that has disconnected from the RVS4000.Â
Â
I have found a work-around, though....No matter How the setting boots up, If I toggle away from and then BACK TO: NAT DISABLED in Advanced Routing, Everything is back operational..... Until the next Power Failure....
Â
Is there any way of making this Automatic.
Â
In another forum, there was a suggestion of putting the E2000 in Bridge mode in WAN settings... I can't find it....
Linksys Wireless Router :: E2000 - Configuring Second One As Repeater Access Point
May 28, 2011I just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.
View 2 Replies View RelatedLinksys Wireless Router :: Turning E2000 Into Access Point / Switch?
Dec 6, 2012we got a At&T Modem/Router upstairs, and then we got a long ethernet cable running from there to the basement. The problem is that this only allows for one LAN connection at a time (an issue for LAN parties and such). I do have an E2000 Linksys router however and I want to be able to use that as like a switch/access point.I am pretty sure this is possible but I have forgotten all of the steps to do it.The att modem/router is running on 192.168.1.254, and my Linksys which is now directly connected is on 192.168.1.1, so I have a different address in that regards.Do I need to edit my Linksys settings now, or do I have to edit the at&t settings?Also I will be using this for Xbox Live at points so will I need to re-open all those ports up on my Linksys, or at least set the DHCP to the Xbox's static IP to keep my NAT good?
View 2 Replies View RelatedLinksys Access Point :: Configure WRT120n As An Access Point?
May 1, 2012Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedLinksys Wrt54g V2 Configure As Access Point?
Nov 28, 2012I don´t really have the RJ45 cable, how to configure it as an access point wirelessly? I mean,just by entering the main menu with the default ip address.
View 1 Replies View RelatedHow To Configure Wireless Access Point To Linksys Router
Jan 18, 2011How do I configure my Linksys N Router for a Netgear Wireless N Access Point set in repeater mode? Linksys and Netgear are communicating, but no Internet access is available on Netgear which makes me think I need to configure Linksys to provide Internet connectivity to the Netgear access point repeater.
View 1 Replies View RelatedHow To Configure Linksys Router Wtr120n As An Access Point
Jan 14, 2012I have a linksys wireless-N router model number is WRT120N and I need to use it as an access point. How i can do that?
View 1 Replies View RelatedLinksys Access Point :: Unable To Configure WAP200
Sep 17, 2008I'm trying to access the WAP200 for the first time. Instructions say Configure your PC to have the static IP address on the same subnet as the Access Point's default address (http://192.168.1.245). So I assumed i would go to TCP/IP properties and type in IP address and subnet mask and the Utility would open.
View 3 Replies View RelatedLinksys Access Point :: Wrt54gx2 With Srx 200 - Configure WAP54G With A MAC?
Jan 8, 2007I have a wrt54gx2 with srx 200 technology recently purchased. I havetwo cabled computers attached. One at one end of the house attached tothe router by ehternet cable, the other attached about 100 ft by ethernet cable.The wireless does not reach to the other end of the house, most likley because that part of the house is an addition with masonary walls and a large masonary firplace. I bought a wap54g access point at the recommendation from someone at linksys to attach to the end of the ethernet run. Since my set up is macintosh, I can't use the wizard disk that came with the wap54g. Linksys support was not support( not expected), I need to know what to do to get this up and running. I am new to this stuff and Linksys get the wireless router with ethernet installed and up and running with my dsl. I thought the same for the wap54g.
View 2 Replies View RelatedLinksys Access Point :: Software To Configure A WAP54G?
Feb 12, 2007I just took over a position where I had to reset a WAP54G because no one knew the encryption key. In working with some of the wireless access points in the past, I know that they came with setup or utility software to find and configure. where I can get a copy. I couldn't find it on Linksys' site.
View 3 Replies View RelatedLinksys Cable / DSL :: Configure WAG120N As Access Point?
Feb 2, 2012i have 2 linksys modems wag120n and wag320n.i am using wag320n as my primary modem and i want to set up wag120n as an access point to provide internet access in another room. what should be the configuration of wag120n?and yes i have read all the post about this subject and tried it all but since there was no actual solution for this problem i decided to open a new post.
View 1 Replies View RelatedLinksys Wireless Router :: How To Configure WRT400n As An Access Point
Aug 13, 2009I would like to configure it as an access point on my LAN, similar to the way my WAP55AG works.My research on the Internet and on these forums indicate that I have to disable DHCP on the router as well as use the LAN ports to connect it to my network.I am able to turn off DHCP, but assigning it a static IP address is challenging.I can set the IP address, but I am unable to set the subnet mask to 255.255.254.0 as I am only getting a set of SM in a drop down list whick are all 255.255.255.x
View 9 Replies View RelatedLinksys Wireless Router :: Configure E1550 As An Access Point?
Nov 8, 2011how to access an E1550 wireless router's settings and configure it to connect to my wireless DSL router? The DSL phone line is not located anywhere near my TV/DVR/Roku and I'd like to connect them wirelessly to our DSL router. The E1550 is next to the TV/DVR/Roku.
View 6 Replies View RelatedLinksys Wireless Router :: Configure Access Point As Repeater For 2.4 GHz Band On WRT610N?
Jun 22, 2010I'm very dissatisfied with the range and signal strength of my new WRT610N dual band router compared to the WAP54G Access Point I used before.Can I configure the Access Point as a repeater for the 2.4 GHz band on the WRT610N if I use the WRT610N as a Wireless G router rather than wireless N?Â
View 5 Replies View RelatedLinksys Wireless Router :: How To Configure E2000 On Linux
Jan 11, 2012I'm a Linux user and just got a new Linksys E2000 router. I attached the router to the computer with the Ethernet cable, and switched the router on, expecting it to work as DHCP server by default, so I could access routers configuration and set it up as needed. This however failed right away. Obviously the router didn't start DHCP, even after I reset with the reset button on the back. Now there is no way to accesss the router to configure it, since web interface path relies on router's DHCP function to access it through 192.168.1.1 which is not working. What can be done to enable it?
View 2 Replies View RelatedLinksys Wireless Router :: How To Setup / Configure E2000
Sep 16, 2010I just bought a Linksys E2000 router and ever since I set it up the internet will cut in and out on my desktop and my laptop, but when I unplug the internet from the router and plug it directly into my desktop (that's how I have it right now) it works perfectly. I have already tried to reconfigure the router and that didn't work either.
View 4 Replies View RelatedLinksys Wireless Router :: Configure E2000 On Linux?
Dec 6, 2011I'm a Linux user and just got a new Linksys E2000 router. I attached the router to the computer with the ethernet cable, and switched the router on, expecting it to work as DHCP server by default, so I could access routers configuration and set it up as needed. This however failed right away. Obviously the router didn't start DHCP, even after I reset with the reset button on the back. Now there is no way to accesss the router to configure it, since web interface path relies on router's DHCP function to access it through 192.168.1.1 which is not working. What can be done to enable it?
View 2 Replies View RelatedCisco Wireless :: Configure E2000 Linksys As Client Device?
Jun 26, 2011I'm trying to configure my Linksys E2000 to be an ethernet attached wireless device to use on computers instead of dongles, etc. I don't want it to route, just act like a Wireless card.
View 1 Replies View RelatedLinksys Access Point :: WRT54G - Unable To Find Access Point In Home Network
Aug 29, 2009I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
Â
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
Â
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.Â
Linksys Access Point :: WAP54G Access Point Setup After A Reset?
Jul 9, 2006I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedLinksys Access Point :: WAP54G Possible To Downgrade Firmware From Access Point
Jan 17, 2013I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedLinksys Access Point :: WRT320N Access Point Vs Range Extender
Dec 14, 2011Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedLinksys Access Point :: WAP4410n MIBs Or OIDs For Access Point
Jul 3, 2012I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedLinksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?
Apr 25, 2011I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
Â
 The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
Â
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Â
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
How To Configure Wireless Access Point
Jun 13, 2011I want to know how to configure wireless access point because i got new internet connection in my home i want to share connection with my nighbour so we bring TP-Link wireless access point bought one cable wire connect with switch and another one connect with TP-LINK access point, but it is not working .now we dont know how it will be work.
View 2 Replies View RelatedHow To Configure A Router To A Wireless Access Point
Apr 17, 2011am trying to find the configuration code and steps to configure a router to a wireless access point.
View 2 Replies View RelatedCisco WAN :: 887 - Configure ISR Wireless Access Point?
May 21, 2011I am trying to configure Cisco 887-W ISR but have hit a stumbling block when trying to configure the wireless access point- or at least the advanced features of the access point using the URL referenced in from the cisco GUI configuration utility (Cisco Configuration Professional ). I do recall previously reading a post which referenced a different URL.
View 2 Replies View RelatedLinksys Wireless Router :: E2000 - Access Restriction Shuts Down Access To All Computer
Jan 1, 2013I have set up access restriction times for my son (we have wireless access for all systems).  I use the MAC address on his systems. Xbox, Kindle Fire and his Laptop. The MAC address are Correct. Here is the problem:
Â
I set the "allow" and times from 6pm - 11:00 pm (while on xmas vacation) - the system works for a while he is shut off as i would like but....
Â
After a period of time the entire house goes off line. I have to reboot the power on e2000 router and then disable the access restrictions. System then works. Problem is repeatable. What is the deal. I have updated firmware already. Otherwise the system works great. Never dies. Just when i set access restricions for a SPECIFIC time it kills entiore houese. BTW i can deny him outright 24/7 and the system idsables his access fine. Its just when i set specific times